Open access peer-reviewed chapter - ONLINE FIRST

Preparation, Characterization, and Swelling Behavior of PEGylated Guar Gum @ Ag Nanoparticles

By Selcan Karakus, Ezgi Tan, Merve Ilgar, Ibrahim Mizan Kahyaoglu, Yeşim Müge Şahin, Demet Sezgin Mansuroglu, Deniz Ismik, Nevin Tasaltin and Ayben Kilislioglu

Submitted: September 6th 2019Reviewed: October 21st 2019Published: November 21st 2019

DOI: 10.5772/intechopen.90227

Downloaded: 25

Abstract

In this study, polyethylene glycol/guar gum @ silver nanoparticles (PEG/GG@AgNPs) were synthesized by using simple sonication method. The nanoparticles were characterized using Fourier-transform infrared spectroscopy (FTIR) and scanning transmission electron microscopy (STEM). The swelling behaviors of nanoparticles were studied in different pHs (5.5 and 7.4). The experimental results were calculated by Fickian diffusion and Schott kinetic models to understand the swelling mechanism and coefficients of the nanoparticles. The results showed that the linear equation of the Fickian diffusion kinetic model was best fit to explain the water diffusion mechanism of the nanoparticle with high correlation coefficient (R2 = 0.982–0.987). The results confirmed that the swelling degree of nanoparticles were 9.71 g/g at pH 5.5. Also, the results confirmed that PEG/GG@AgNPs can be a good candidate for drug delivery systems in pharmaceutical applications.

Keywords

  • swelling behavior
  • guar gum
  • Ag nanoparticles

1. Introduction

Nanotechnology focuses on many fundamental disciplines such as physics, chemistry, materials science, and biology [1]. Recently, the synthesis of the nanostructures has gained a great attention due to superior properties (mechanical, optical, thermal, biological, physical, and chemical) as compared to conventional materials [2, 3, 4, 5].These superior properties depend on the size, composition, shape, and origin of nanostructures [6, 7]. As a general definition, nanostructures are 1–100 nanometers in size in which case they have a high surface area-to-volume ratios and their reactivities are effected mostly depending on their different shapes such as spherical, conical, spiral, cylindrical, tubular, and hollow [8, 9].

Many researchers have reported that iron [10], copper [11], gold [2], and silver [12] were used often for the preparation of stable dispersions of nanoparticles due to their biocompatibility and biodegradability and less reactivity in the biomedical applications. Silver nanoparticles (AgNPs) with desired morphologies, well-known for their antimicrobial activity, are used in both ionic and metallic forms which are incorporated inside the polymer matrix, with excellent biocompatibility [13]. It was known that bare silver nanoparticles were prone to oxidation and tarnishing. Thus, we used PEG/GG polymer blends to improve the dispersion stability and prevent agglomeration of silver nanoparticles in aqueous environment [14].

During the preparation of hydrogels, mostly preferred biopolymers are alginate, chitosan, gum arabic, agar, carrageenans, and guar gum [15, 16, 17, 18, 19]. Among these biopolymers, GG is used in the fields of food industry and pharmaceutical and cosmetic applications [20, 21, 22]. It is not desirable to prepare silver nanoparticles by chemical methods using toxicological chemicals such as reducing agents [23]. For this purpose, we chose a dual biopolymer blend (GG and PEG) which will carry out the green synthesis and improve the distribution. GG is a nonionic water-soluble polysaccharide and consists of galactomannan which has a linear chain of (1-4)-β-D-mannopyranosyl units interposed with (1-6)-α-D-galactopyranosyl units distributed as side branches [24]. PEG is a stabilizer effective for the control of size and shape of nanoparticles and also has role on the reduction of silver ions [25].

The key points of the chapter were (i) the green synthesis and (ii) swelling of nanoparticles. The aim of this study was to obtain NPs consisting of PEG/GG and zero valent Ag by using the simple sonication method. We prepared nanoparticles in the presence of silver nitrate in GG/PEG (2:1 mixing ratio) polymer blends. In particular, we performed a green synthesis sonochemical process to reduce Ag ions to form AgNPs by using ultrasonic method without the use of dangerous stabilizing agents such as any reducing agent and surfactant [26]. The breaking of cavitation bubbles under high temperature and pressure and the hydrogen radicals (H*) and hydroxyl radicals (OH*) in the water formed by the ultrasonic effect play an important role in the reduction of Ag ions and the formation of AgNPs [27].

All samples were characterized by using FTIR and STEM techniques. SEM images revealed good compatibility and homogeneous distribution between the PEG/GG matrix and Ag. AgNPs were found to be <500 nm in size. Moreover, we have also demonstrated the swelling behavior of the prepared nanoparticles in finding out the potential of the nanoparticles for drug delivery systems. The swelling uptake (%) of PEG/GG@AgNPs was found to be % 670.5 at pH 5.5.We determined the swelling behavior such as the maximum swelling and gel fraction of samples to interpret the water absorption results. All results showed that one could control the size and the shape of zero valent Ag nanoparticles by polymer blend under the sonication effect.

2. Materials and methods

2.1 Materials

Guar gum (99% purity, average molecular weight of 2.8 × 105 g mol−1) and polyethylene glycol (PEG 400) were obtained from Fluka (Switzerland). Silver nitrate (AgNO3), sodium hydroxide (NaOH), and dimethyl sulfoxide (DMSO) were obtained from Merck (Pvt.) Ltd. Mumbai, India. Polyethylene glycol 400 (PEG) (molecular weight of 400 g/mol) was purchased from Sigma-Aldrich, Chemie GmbH, USA.

2.2 Preparation of nanoparticles

2.2.1 Preparation of PEG/GG@AgNPs

GG solution (0.5 g GG in 100 mL of deionized water) and PEG (5 mL) were mixed by stirring with a magnetic stirrer at 25°C for 10 min. 5 mL of AgNO3 (0.1 M) solution was added into GG/PEG solutions and then was sonicated for 15 min. 0.1 M NaOH was added into the solutions until pH 8.4.

2.3 Characterization

Samples were ground with KBr powder and analyzed from 4000 to 600 cm−1 with a resolution of 4 cm−1 using eight scans by using a PerkinElmer FTIR emission spectrometer (Spectrum Two). Samples were scanned in the dark-field area with the wet STEM detector by using FEI QUANTA S50 (A copper grid, Ted Pella, support films, carbon type A, 300 meshes was utilized). STEM holder was cooled to 2°C and the pressure was set between 700 and 1300 Pa.

2.4 Swelling studies

2.4.1 Measurement of the water absorbency

The swelling degree (St, g/g) was calculated from Eq. (2):

St=WtWdWdE1

where SW is the swelling degree per gram dried sample (g g−1), Wd is the mass of dried samples at time t (g), and Wt is the mass of swollen samples at time t (g) [28].

2.4.2 Calculations of the swelling behavior

The swelling behavior was explained by applying different kinetic models such as Fickian diffusion and Schott second-order dynamic model given in Eqs. (2)(7) [29, 30]. To identify the swelling kinetic mechanisms of the prepared samples, the swelling kinetic parameters were evaluated according to models:

Fickian diffusion swelling kinetic models:

St=Sx1ekWtE2

When Eq. (2) was linearized

LnStS=Lnk+nLntE3

where t is time (min), k is the rate constant (min−1), St is the water absorption capacity at time t, and Sis the water absorption capacity at equilibrium. The plots of LnSt/Sversus Ln t were drawn to calculate the parameter (k) of kinetic model and the linear correlation coefficient.

Schott proposed the second-order kinetic model to elucidate the swelling mechanism of the system, and this model was related to the swelling rate at any time and was proportional to the quadratic of the swelling capacity before the equilibrium state [30, 31]:

dSdt=ksStS2E4

When the initial condition was t = 0 and S = 0

tS=A+BtE5
A=1ksS2E6

where t is time (min), S is the swelling capacity at time t (g g−1), A is the reciprocal of initial swelling rate, and B is the reciprocal ofS. The plots of t/W versus t were drawn to calculate the parameters (A and B) of kinetic model and the linear correlation coefficient.

To explain the water diffusion mechanism, fractional solution capacity (F: St/S) less than 0.60 was analyzed using the following equation (Eq. (7)):

StS=ktnorF=ktnE7

where t is time (min), Wt is the uptake capacity of the sample at time t, Sis the capacity of the sample at swelling equilibrium (g), k is the gel characteristic constant, and n is the swelling index (n < 0.5 for Fickian diffusion and 0.5 < n < 1 for non-Fickian; n = 1 for relaxation controlled transport and n > 1 for II diffusion) [30].

The Fickian diffusion model had another expression shown as Eq. (8):

StS=4Dπl21π2+2n=1x1nierfcnl2DtE8

Diffusion coefficient D (cm2/s) was calculated using Eq. (9). For short times, Eq. (9) was used at the early-stage diffusion coefficient of water by

StS=4Dπl2E9

where l was the diffusional distance [32, 33].

3. Results and discussions

3.1 Swelling kinetics

Swelling ability is known to be associated with free hydrophilic groups and surface properties [34]. The sonication method, which is associated with various factors such as ultrasound power, ultrasound frequency, modification time, and temperature, changes the surface properties [35]. In this study, the swelling kinetics was investigated to determine the surface properties of the novel PEG/GG@AgNPs obtained by using sonication method. To analyze the effect of sonication on the swelling kinetic mechanism of the synthesized nanoparticles, swelling kinetic results were observed gravimetrically and performed in pH 5.5 and 7.4 at 25°C. The equilibrium swelling degrees, Fickian and Schott kinetic models of PEG/GG@AgNPs were given in Figures 1, 2, 3, respectively and the swelling behavior followed a similar behavior due the high surface area.

Figure 1.

Effect of two different pH mediums on the swelling kinetics of PEG/GG@AgNPs.

Figure 2.

Plots of Fickian kinetic model for PEG/GG@AgNPs.

Figure 3.

Plots of Schott kinetic model for PEG/GG@AgNPs.

The O-H groups of the PEG/GG@AgNPs formed hydrogen bonds with water molecules and absorbed water [36]. The equilibrium swelling degrees of PEG/GG@AgNPs were 9.71 gg−1 (pH 5.5) and 3.82 gg−1 (pH 7.4). According to the experimental swelling results, the swelling degree of the PEG/GG@AgNPs increased within the first 10 minutes and then slowed down until reaching equilibrium after 15 min in two different pH mediums. In this case, the results showed that the nanoparticle had shown greater interest in the water molecules and was proof that it binds with O▬H groups in the structure which allowed it to swell in a short time in pH 5.5. In order to explain swelling behavior of the nanoparticle, the swelling parameters were calculated by using the Fickian diffusion and Schott’s second-order kinetic models. The calculated swelling kinetic parameters and the correlation coefficients (R2) for all the models for the nanoparticles were given in Table 1.

SampleFickian kinetic modelSchott kinetic model
nkR2S(exp)k2 (g/g min−1)R2
pH 5.50.512.500.9871.391.0520.978
pH 7.40.532.720.98252.630.0010.070

Table 1.

Values of various parameters associated with swelling kinetic models.

The results showed that the linear equation of the Fickian diffusion kinetic model was best fit to explain the water diffusion mechanism of the nanoparticles with high correlation coefficient (R2 = 0.982–0.987). According to the Fickian kinetic model, n is known to explain the diffusion mechanism of the solvent. The n values of the nanoparticles were calculated to be in the range of 0.5–1, which was explained by a non-Fickian diffusion behavior of the water transport mechanism [36].

3.2 STEM analysis

To investigate the effect of ultrasonic irradiation on the surface properties of the nanoparticle, the STEM images of PEG/GG@AgNPs were presented in Figure 4. It could be clearly seen that the surface of PEG was a homogeneous surface in spherical nanoform with the uniform dispersion of AgNPs. It was concluded that the ultrasonic irradiation may play a role in obtaining homogeneous distribution of the nanoparticles.

Figure 4.

STEM image of PEG/GG@AgNPs.

With this structural feature, nanoparticles have been used in different applications such as sensor, drug delivery system, and pharmaceutical applications [37, 38, 39, 40, 41].

3.3 FTIR analysis

The FTIR spectrums of pure GG and PEG/GG@AgNPs were given in Figure 5. The FTIR spectrum of pure GG showed peaks at 3499 (▬OH stretching), 2989 (C▬H stretching), and 1030 (▬OH bending) cm−1. The FTIR spectrum of PEG/GG@AgNPs showed peaks at 2980 (C▬H stretching), 1540 (COOH), 1470 (C▬H stretching), and 1370 (▬C=O) cm−1. The peaks recorded at 3499 cm−1 of GG expressed in AgNPs indicated that -OH groups were utilized for the stabilization of AgNPs. From the results of the FTIR, we found that reduction and stabilization occurred in AgNPs. Singh et al. observed similar results [42].

Figure 5.

The FTIR spectrums of pure GG and PEG/GG@AgNPs.

4. Conclusions

In this study, PEG/GG@AgNPs were prepared by using sonochemical method. The swelling ability of nanoparticle was investigated in two different pHs. The mechanism of swelling kinetics was explained, and it has been found that the mechanism follows the Fickian diffusion model. In summary, this study was focused on the green, low-cost novel method for producing Ag nanoparticles. The NPs could be served as a promising candidate nanocarrier for drug delivery systems due to its the swelling degrees.

Acknowledgments

The authors acknowledge the STEM and FTIR analysis support from ArelPOTKAM, Istanbul, and Zeynep Akça.

Download

chapter PDF

© 2019 The Author(s). Licensee IntechOpen. This chapter is distributed under the terms of the Creative Commons Attribution 3.0 License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

How to cite and reference

Link to this chapter Copy to clipboard

Cite this chapter Copy to clipboard

Selcan Karakus, Ezgi Tan, Merve Ilgar, Ibrahim Mizan Kahyaoglu, Yeşim Müge Şahin, Demet Sezgin Mansuroglu, Deniz Ismik, Nevin Tasaltin and Ayben Kilislioglu (November 21st 2019). Preparation, Characterization, and Swelling Behavior of PEGylated Guar Gum @ Ag Nanoparticles [Online First], IntechOpen, DOI: 10.5772/intechopen.90227. Available from:

chapter statistics

25total chapter downloads

More statistics for editors and authors

Login to your personal dashboard for more detailed statistics on your publications.

Access personal reporting

We are IntechOpen, the world's leading publisher of Open Access books. Built by scientists, for scientists. Our readership spans scientists, professors, researchers, librarians, and students, as well as business professionals. We share our knowledge and peer-reveiwed research papers with libraries, scientific and engineering societies, and also work with corporate R&D departments and government entities.

More About Us