Open access peer-reviewed chapter

Co-Design Block PA (Power Amplifier)-Antenna for 5G Application at 28 GHz Frequency Band

Written By

Ange Joel Nounga Njanda and Paul Samuel Mandeng

Reviewed: 31 May 2021 Published: 07 December 2021

DOI: 10.5772/intechopen.98653

From the Edited Volume

Antenna Systems

Edited by Hussain Al-Rizzo and Said Abushamleh

Chapter metrics overview

466 Chapter Downloads

View Full Metrics


This subject addresses the issue related to Transmitters for the new communication standard, namely 5G. Indeed to respond to the problems of radio coverage, the speed of services as well as the rise in user demand, transmitters must have ideal characteristics to be able to meet these requirements. This chapter proposes in order to answer such a problem a block made up of a linear array of antennas has 4 elements and a transistor amplifier operating at the 28 GHz frequency band. The Design of the Block is done first by the design of the antenna then the design of the amplifier and finally the junction of the two devices with a matching network to therefore form the block of transmitters Speaking of the design of the antenna, the prepared antenna is a patch antenna with a patch shape excluding the classic shapes which is printed on a Rogers-Duriod 5880 substrate so the thickness is 0.127 mm, the linear antenna array proposed has a gain greater than 15 dB and a Good Bandwidth, the transistor amplifier is in turn printed on the same substrate has the same thickness to minimize the losses during the junction of this one with the antenna, this amplifier offers a higher gain than device 15 dB and therefore the Bandwidth is greater than 2 GHz, each transmitter has an input and output reflection coefficient of less than −10 db. The simulation of each transmitter is made with the CST-microwave software for the Antenna and the ADS (Advanced Design System) software for the amplifier and the Block PA-Antenna. It is important to note that the Block output impedance is 50 ohms making our device more practical and easily commercial.


  • 5G
  • Antenna
  • PA (Power Amplifier)

1. Introduction

In recent years, wireless communication systems have had a significant impact on the daily life of human beings, therefore nowadays more and more users are connecting their devices to existing networks causing a constant increase in data traffic and the need for high speed networks will continue to increase over the years [1, 2, 3]. To cope with this rise the new 5G communication systems would have to dramatically improve the communication capacity by exploiting enormous unlicensed bandwidth in particular, in the millimeter waveband. It should also be prepared to provide and support very high data rates which in turn therefore requires the design of antennas and amplifiers satisfying the expected data rate [4, 5, 6]. Research in 5G Millimeter Band wireless communication shows that as mobile industries developed to use the millimeter wave spectrum, carriers are likely to use the 28, 38 and 73GHz bands which will become available in future technologies [7]. The requirements imposed by 5G technology on the antennas are: lightweight antenna, low profile, low cost mass production, ease of installation, Despite its narrow band the microstrip patch antenna may prove to be an ideal candidate to meet these requirements and the design of a microwave amplifier becomes very interesting in view of the operation of 5G technology in millimeter band. This chapter proposes the design of a microstrip patch antenna and an amplifier for 5G application then a PA-Antenna Unit operating in the 28 GHz band. In the following lines we will respectively present the architecture of our Co-Design then the mathematical model of the antenna and the amplifier as well as their modeling then the interpretation and analysis of the results and finally the conclusion.


2. PA-antenna Co-design architecture

The principle of the Co-Design of a PA-Antenna block is based on the fact that the junction of the antenna and the amplifier must be done with as little loss as possible, which is why it is very objective for us to work on each one. Equipment with a reference impedance which will facilitate the junction of the two because the option of designing a matching network no longer becomes a necessity. So let us say the stages of Co-design illustrated in the figure below (Figure 1).

Figure 1.

PA-antenna block Co-design principle.

In the chain of transmission of wireless communication systems, the proposed Co-Design Block is of capital importance because the amplifier will have the role of taking a weak signal as input and producing a high intensity signal at the output. This signal will be recovered at the output by the antenna and radiates by it in the free space.


3. Mathematical model and modeling of the antenna and the amplifier

3.1 Mathematical model of the antenna

In this section we will notify the different formulas used to obtain the dimensions of the rectangular patch:

3.1.1 The width of the WP patch is expressed as follows


where C is the speed and εr the dielectric constant of the substrate.

3.1.2 The length of the patch is expressed by the formula


where the effective dielectric constant is expressed by the formula


Where h is the height of the dielectric substrate, the extension of length ΔL is expressed by the following formula:


3.1.3 Dimension of the ground plan

The dimensions of the ground plane are expressed by the following formulas:


Wg: Ground plane width in mm, Lg: Ground plane length in mm.

The feeding technique used for our antennas is the microstrip feeding technique because of its ease of manufacture and its better reliability according to [8].

3.1.4 Adaptation technique

The choice of the feeding technique chosen therefore imposes a choice of adaptation technique in our work we have chosen the insed feed adaptation technique. This technique involves inserting notches to bring the impedance of the antenna down to that of the power line [9]. Each notch is equivalent to a parallel admittance Y with a conductance G and a subceptance B. The following formulas on the conductance of a slot, the mutual conductance and the resistance of the antenna are expressed as follows


The mutual conductance is expressed as follows:


Wherej0: represents the Bessel function of order 0. The resistance of the antenna is


After having developed all the theoretical analysis which allows us to find, using mathematical formulas, the various parameters important for the design of the antenna, we will now proceed to the modeling of the antenna.

3.1.5 Antenna modeling

The previous section allowed us to show how to obtain the different antenna dimensions of a rectangular patch antenna. Table 1 below illustrates these dimensions.

DimensionValue (mm)

Table 1.

Antenna dimension.

When modeling the antenna several initiatives were taken first with the proposal of several antenna shapes departing from the known classical shape. The Figures 2 and 3 below represent the different forms of modeled antennas.

Figure 2.

Rectangular patch modeled: a) with dimension, b) without dimension.

Figure 3.

Proposed patch antenna shape.

The Other forms of antennas modeled in terms of contribution are illustrated below.

3.2 Mathematical model of the amplifier

An Amplifier is an electronic device whose role is to increase the power of a signal introduced at its input. To simplify our study we will admit that our amplifier is a quadrupole whose matrix is [S] and connected to a voltage source E with an internal impedance and it is loaded by an impedance (Figure 4).

Figure 4.

Distribution waves and reflection coefficients at the entry and exit of the quadrupole.

The matrix [S] of distribution of this linear quadrupole is such that [9]:


Z2: is the output impedance of the quadrupole fed by the Zs impedance source.

a1: is the incident wave at port 1;

b1: is the wave reflected at the access;

a2: is the incident wave at port 2;

b2: is the wave reflected at port 2.

When making the amplifier, we try to have maximum gain. In other words, it is necessary to perform the adaptation at the input of the transistor and the source simultaneously with the adaptation between the transistor output and the load.

3.2.1 Presentation du transistor

The transistor amplifier are very recurrent microwave amplifiers their characteristics depend on the properties of the Transistor for the design in our work we looked at the FET transistor sp_aiiAF035P1_00–19941209 manufactured by Alpha Industries so we will first illustrate the characteristics of our transistor namely the input and output reflection coefficients S11, S22 the transmission coefficient S21 which represents the transmission from the input to the output or the own gain of the transistor and of the future amplifier S12, represents the isolation or the reverse transmission from the output to the input the drain source voltage Vds = 5 V and the current Ids = 70 mA. We will therefore present and illustrate the S-parameters listed below in Figure 5.

Figure 5.

Schematic of the transistor and simulation of S-parameters.

The S-parameters of the transistor obtained are as follows: S11 = −1.067 dB, S22 = −0.219 dB, S21 = −11.164 dB, S12 = − 35.289 dB. We realize that the inherent gain of the transistor is very low, it is imperative for us to improve this gain as well as the characteristics of the amplifier in order to produce an amplifier that meets the constraints imposed by 5G technology.

3.2.2 Study of the stability of the transistor

Considering K as the stability factor, the expression of the stability factor is given by the following formula:


and if Δ<1 and if K > 1 then the transistor is unconditionally stable [9] Δ: The determinant of the matrix S


The Stability constant K of the transistor and mod_delta Δ are respectively 1.267 and 0.861 whose transistor is unconditionally stable.

3.2.3 Architecture of a microwave amplifier

The architecture of a Microwave Amplifier is shown as follows (Figure 6).

Figure 6.

Microwave amplifier.

3.2.4 Modeling of the microwave amplifier

For the design of the amplifier, we will first start with impedance matching. The adaptation with Stub has been opted for by this document. The structure of the stub is shown in Figure 7 below.

Figure 7.

Stub structure.

Figure 8 below shows the S-parameters of the Stub.

Figure 8.

Stub S-parameters.

The validation of our Stub is confirmed by an impedance adaptation to 50 ohms at the input and at the output the table below summarizes the result obtained (Table 2).

S11 (dB)−15.062
S22 (dB)−15.062
S12 (dB)−0.637
S21 (dB)−0.637

Table 2.

Summary of the Sparameters of the stub.

The above table presents the results of synthesis of the S-parameters of the stub at the resonant frequency of the transistor. From these results, it can be seen that: S11 = S22, S12 = S21 Hence, the matching of the impedance is good, because the waves leaving the source and passing through the line are not partly reflected when they arrive on the load.

The design of the transistor amplifier is shown in the Figures 9 and 10 above.

Figure 9.

Microwave amplifier without stage of transistor.

Figure 10.

Microwave amplifier with stage of transistor.


4. Presentation of the results

4.1 Antenna case

The Antenna Parameters shown below are: Reflection Coefficient S11, Voltage Standing Wave Ratio (VSWR), Antenna Gain in (dB), and Antenna Input Impedance in Ohms The S11 reflection coefficient is the parameter demonstrating whether the antenna adaptation is good or not, the criterion for defining good adaptation through this parameter is S11 < −10 dB. The Figure 11 below illustrate the S11 parameter of the antennas.

Figure 11.

Antennas parameter S11.

The Voltage Standing Wave Ratio (VSWR) is the parameter demonstrating if the adaptation of the antenna is good the characteristic value is VSWR ≤2 the Figure 12 illustrates the voltage standing wave ratio obtained by the antennas.

Figure 12.

Stationary wave ratio of antennas.

The gain of the antenna characterizes the capacity of the antenna to radiate the maximum power that is ingested at its input. The Figure 13 illustrate the gain of antennas.

Figure 13.

Antennas gain.

The input impedance of the antenna obviously shows whether we have suitably adapted the antenna or not, it is also clear that this is one of the conditions to be satisfied in order to be able to make our Co-Design Block PA-Antenna the Figure 14 below illustrates the impedance of our antennas.

Figure 14.

Antenna input impedance.

In the summary of the Figures 2 and 3 presented above we have proposed 04 antenna shapes the first shape (Figure 2) is the classic rectangular patch template then the other shapes offered are patch templates excluding classic models (Figure 3). We can obviously note that the antennas have a good adaptation and an input impedance at 50 ohms but the gain proposed by these antennas are quite low because the strongest gain proposed here is 7.25 dB to improve these gains so we have model antenna arrays. An antenna array: is the combination of several antenna of the same type in order to form a single antenna the assembly of the different radiating elements must respect a certain distance between radiating element the standard pitch most used in most cases is not worth = 0.5λ for our work we will be interested in linear networks and we will model this one with 4 elements so the distance between will be worth 0.5λ Figure 15 below presents the modeling of the two antenna arrays the step of value 0.5 λ is 5.36 mm. The Figure 15 below illustrates the configuration of these antenna networks.

Figure 15.

Linear antenna arrays modeled with different shape.

The reflection coefficients observed in each of the antenna networks below are illustrated in the Figure 16 below.

Figure 16.

S11 reflection coefficient of antenna arrays.

Figure 17 shows the gains obtained by these different antennas network.

Figure 17.

Gain of different antenna network.

We are now going to explore the gain of the antenna arrays in the E plane in order to observe the side lobes generated; the Figure 18 below illustrates it.

Figure 18.

Representation of gain in plan E of antenna network.

To confirm the validity of our results, the representation of the impedances of the antenna networks are illustrated in Figure 19 below.

Figure 19.

Input impedance of antenna networks.

It is clear that the impedance presented by our input antenna arrays is 50 ohms at the resonant frequency. We will summarize our work on Antennas in the table below (Table 3).

4.1.1 Analysis of results and interpretation

The results obtained must be compared with those which have already been the subject of research and accepted in the scientific research community (Table 4).

Antenna ParametersValues
S11 (dB)−15.6Single antenna with different shape offered
−15.515Antenna has 4 elements with different proposed shape
Gain (dB)7.25Single antenna with different shape offered
13Antenna has 4 elements with different proposed shape
Bandwidth(MHz)550Single antenna with different shape offered
504.59Antenna has 4 elements with different proposed shape
Efficiency (%)76.82Single antenna with different shape offered
75.3Antenna has 4 elements with different proposed shape
Impédance (ohms)50 ohms

Table 3.

Summary of antenna parameters.

RefS11 (dB)Gain (dB)VSWRBandwidth(GHz)Efficiency (%)
This Work−

Table 4.

Comparative analysis at the antenna level.

Comparing our works to those listed, it is clear that our obtained gain is greater than the proposed works, the bandwidth obtained is better compared to the works [11, 18]. The reflection coefficients obtained are better compared to works [16, 15] but the bandwidth obtained in these works is better than ours. We can therefore deduce from these works that our antennas comply with and meet the requirements imposed by 5G technology.

4.2 Amplifier case

After modeling the amplifier, it is therefore important to observe the parameters obtained by the amplification after simulation. The S-parameters of the amplifier are summarized in Figure 20 below.

Figure 20.

S-parameters of the amplifier without stage transistor.

The S-Parameters of the amplifier with stage transistor are shown in Figure 21 below.

Figure 21.

S-parameters of amplifier with stage transistor.

As we notice in our figures above the amplifier presents 04 parameters namely S11, S22, S12, S21 the parameters S11, S22 respectively represent the reflection coefficients at the input and at the output of the amplifier and the parameter S12 represents isolation, the parameter S21 represents the amplifier transmission gain. The goal of making a transistor stage is therefore to improve the transmission gain of the amplifier. The Table 5 below illustrates the characteristics of the amplifier.

Figure 22.

Co-Design Block PA-Antenna.

The following table establishes a comparison between our work and the work carried out by [19] (Table 6).

Amplifier ParametersValues
Amplifier without stagesAmplifier with stage
S11 (dB)−30.784−29.645
S22 (dB)−16.978−16.779
S12 (dB)−16.445−32.941
S21 (dB)7.6815.31
Impédance d’entrée ou de sortie50 ohms
Bandwidth (GHz)Greater than 2GHz

Table 5.

Summary of amplifier parameters.

ParametersThis Work[19]
Frequency (GHz)2828
S11 (dB)−29.645−13.124
S22 (dB)−16.779−15.455
S12 (dB)−32.941
S21 (dB)15.3110.803

Table 6.

Comparative analysis at the amplifier level.

Our results obtained in simulation are much better than that obtained in [19]. Our amplifier has a gain of 15 dB which shows that our amplifier meets the requirements imposed by 5G technology.


5. Co-design block PA-antenna

The Co-Design Block PA-Antenna can be done with the greatest serenity because the impedances of the two equipment’s comply with the principles listed above. The figure below therefore illustrates the proposed PA-Antenna Co-Design (Figure 22).

Figure 23.

Co-Design PA-Antenna Parameter S11.

The results obtained after simulation show us the following characteristics illustrated in the Figure 23 below.

The S11 parameter clearly shows us that our Co-Design is functional and well suited to the resonant frequency. In this chapter we enumerate a method of designing a transmitter block namely the antenna and the amplifier it is important to note that the design of the block requires the partial design of each of the transmitters in order to consider the design of the block. The design of the block takes into account the impedance adaptation parameters this as well as in this chapter we have arranged such that the amplifier and the antenna present at input as at output an impedance of 50 ohms thus facilitating the junction of the two block the proof Figure 23 illustrates clearly and clearly that the block is functioning correctly and the impedances of the various equipment are in conformity with the fixed reference impedance.


6. Conclusion

Having reached the end of this chapter, the objective of which is to propose a PA-Antenna Co-Design block for 5G applications, it is clear that the design of such a device requires fairly strict requirements and methodology. Therefore, we looked at the design on the one hand of the antenna and on the other hand of the amplifier by setting 50 ohms as the working impedance guaranteeing the adaptation of the impedance of the device. After design of the two equipment’s separately. We therefore proposed and simulated said device. This has characteristics that meet the requirements imposed by 5G technology, which should be noted that the antennas and amplifier proposed in this chapter offer very good characteristics compared to some existing equipment and presented in this chapter. It is also necessary to note the double resonance of our antenna in the 46.06 GHz band and presenting in this one an impedance of 50 ohms and a good bandwidth.



All my thanks go to my teachers at the National Polytechnic School of Douala Cameroon for their teachings and advice. My thanks go to the Intech-Open author community who will shed some light on this work to make it even better.



In this chapter, it is clear that we have only had the possibility of simulating our project with the reference software, namely CST microwave and ADS. In this declaration we ask the community to offer us the possibility of being able to design our project indeed we are engineers in Telecommunications and the means to develop such technologies in our country Cameroon is extremely difficult so it will be a huge pleasure for us to have the chance to be able to realize our project thanks to your help.


  1. 1. Dahlman, G. Mildh, S. Parkvall, J. Peisa, J. Sachs, Y. Selen, and J. Skold, 5G wireless access: Requirements and realization, IEEE Communication Magazine, 2014, pp. 42-47
  2. 2. X. Gu, A multilayer organic package with 64 dual-polarized antennas for 28GHz 5G communication, In Proceedings of the IEEE International Microwave Symposium, 2018, pp. 1899-1901
  3. 3. Dheeraj M, Shankar D. Microstrip Patch Antenna at 28GHz for 5G Applications. Journal of Science Technology Engineering & Management Advanced Research and Innovation. 2018;1(1):21-22
  4. 4. Adepu V. A 28GHz FR-4 Compatible Phased Array Antenna for 5G. IJESAT (International Journal of Engineering Science and Advanced Technology). 2017;7(4):305-310
  5. 5. J. Zhang, M. Guizani, and Y, Zhang, 5G Millimeter-Wave Antenna Array: Design and Challenges, IEEE Wireless Communication, 2017, pp. 106-112
  6. 6. Darboe O, Onyango DB, Manene F. A 28GHz Rectangular Microstrip Patch Antenna for 5G Applications. IJERT (International Journal of Engineering Research and Technology). 2019;12(6):854-857
  7. 7. James JR, Hall PS. Handbook of Microstrip Antenna. London; 1989
  8. 8. S. Pradhan, D. Choi, “Inset Fed Microstrip Patch Antenna for Wireless Communication at 2.45 GHz”, Journal of the Korea Institute of Information and Communication Engineering, Vol.18, No.8, 1785 1790 Aug. 2014
  9. 9. David M. Pozar, Daniel H. Schaubert, “Microstrip Antenna Array Design”,in Microstrip Antennas:The Analysis and Design of Microstrip Antennas and Arrays, 1, Wiley-IEEE Press, 1995, pp.448
  10. 10. Bakry M, Hegazy EA. Design and Analysis of 28GHz Rectangular Microstrip antenna. WSEAS Transactions on Communications. 2018;17:2224-2864
  11. 11. S. Johari, M. A. Jalil, S. I. Ibrahim, M. N. Mohammad, and Norhafiza, 28 GHz Microstrip Patch Antennas for Future 5G, Malaysian Journal of Engineering and Science Research, 2018, 2(4), 01-06
  12. 12. Goyal RK, Modani US. A Compact Microstrip Patch Antenna at 28GHz for 5G Wireless applications. Third International Conference, and Workshops on Recent Advances and Innovations in Engineering: IEEE Conference Record; November 2018
  13. 13. M. Abdelsalam M. Omar, A. M. Elgnai, E. H. Abuo, Design and Analysis of Millimeter Wave Microstrip Patch Antenna for 5G Applications, International Conference on Technical Sciences, 2019, pp.137-142
  14. 14. A. F. kaeib, N. M. Shebani, and A. R. Zarek, Design and Analysis of a Slotted Microstrip Antenna for 5G Communication Networks at 28GHz, 19th International Conference on Sciences and Techniques of Automatic control and Computer Engineering (STA), March 2019
  15. 15. Y. Ghazaoui, A. El Alami, M. El Ghzaoui, S. Das, D. Barad, and S. Mohapatra, Millimeter-wave antenna with enhanced bandwidth for 5G wireless application, Journal of Instrumentation (JINST), January 2020
  16. 16. Kavitha M, Dinesh Kumar T, Gayathri A, Koushick V. 28GHz Printed Antenna for 5G Communication with Improved Gain Using Array. International Journal of Scientific and Technology Research. March 2020;9(3):5127-5133
  17. 17. Sivabalan A, Pavithra S, Selvarani R, Vinitha KM. Design of Microstrip Patch Antenna for 5G. International Journal of Control and Automation. 2020;13:546-552
  18. 18. M. Darsono and A R. Wijaya, Design and Simulation of a Rectangular Patch Microstrip Antenna for the Frequency of 28GHz in 5G Technology, International Conference on Innovation in Research, Journal of Physics: Conf. Series 1469 (2020) 012107, pp. 1-7. doi:10.1088/1742-6596/1469/1/012107
  19. 19. Nur Syahadah Yusof, Mohamed Fauzi Packeer Mohamed, Mohamad Faiz Mohamed Omar, Mohd Fadzil Ain, Norlaili Mohd Nor, Mohamad Adzhar Md Zawawi, Mohammad Khairi Ishak , Mohd Hendra Hairi, 28 GHz Off-the-Shelf Low Noise Amplifier for 5G Baseband Wireless System, International Journal of Innovative Technology and Exploring Engineering (IJITEE) ISSN: 2278-3075, Volume-9 Issue-3, January 2020

Written By

Ange Joel Nounga Njanda and Paul Samuel Mandeng

Reviewed: 31 May 2021 Published: 07 December 2021