Percentagedecayof themicrosensor
1. Introduction
The optical fiber systems until now have turned out to be an ample resource that offers alternatives for tasks of detection and transduction of the energy forms, as a classification of these optical fiber transducers, in this task we presented a sensor that belongs to those of the refractometric type. Since1995,researchersKhotiaintsevSergei, VictorDeLeonParedes, EstebanMolinaFlores, AlexandreZemliakmadeatheoretical modelinganalysisof a varietyofrefractometricsensorsbased on apairoffiber optic ends, all usefulformeasurementofrefractive indices. These sensors had an oblique disposition, andtheseresearchesareconductedthe analysisofbest responseon the degreeofmisalignmentoftwofibers, and to the resulting form of its hemispherical surface of contact with surrounding means. These researches always were within the theoretical regime and for monochromatic irradiation, and never had a tangible evidence of an experimental result (Jones & Zimmer, 1978; Molina-Flores, 1995; Khotiaintsev et al, 1996, 2000, 2002). In 2005 the researcher Esteban Molina Flores, main adviser of this work, proposed and managed to realize the micromachining, one of this microsensorial element with technology of electrical arc, in his particular parallel fiber version, and with surface of semidrop, obtaining theoretical and experimental results in his characterization in the infrared region (1550 nm) for this refractometric microsensor. Like integral part of the research line, the refractometric sensors developed by researcher Esteban Molina Flores (Molina-Flores, 2006), in this occasion through this project, theoretical and experimental results from this microsensor operating in the infrared region are presented, whose particular applying are to solve the problem of the detection, identification and measurement of liquid levels in a cistern tank, by means of the identification of the interface of the immiscible liquids: water and oil engine, and of the interface air-oil engine. The objectives of this work are divided in two kinds of objectives: General objective: realize the characterization of a refractometric microsensor in the infrared region. Particular objectives: a) Make our own sensor of semidrop, b) Establish the conditions of the installation and application of the microsensor with which its efficient operation is guaranteed, c) To realize the theoretical proposal of a design of application of the microsensor of semidrop for the detection of a pair of immiscible liquids. The order in which the sections were considered, obeys to the intention to show the reader the development stages through which it passed the microsensor until the publication of the results in indexed magazine.
2. Manufacturing of the microsensor
In this project the methodology of manufacture of a refractometricmicrosensor of fiber is presented, which is elaborated from a pair of adjacent fiber tips of parallel disposition, which are fused on a specific form in one of its ends to form a semidrop that serves like detection or refractometric interaction surface with the liquid in submission, see Fig. 1.
2.1. Optical fibermicrosensor micromachining
The technology implemented in this project is based on heat source by electrical arc.
The physical manufacture of the microsensor is repeatable every time respecting the characteristics of electric power applied to melt the glass fiber to 1900º C, and the specific moments and points in which they are applied time and time again to obtain the form of the semidrop, and to guarantee therefore the awaited optical response in this microsensor. This sensor can be excited with a visible or infrared irradiation source, behaving the fibers like fibers monomodal or multimodal, respectively. The preparation of the optical fiber ends is of the same way in which the optical fiber ends are prepared to realize a common and current splice of low loss. This procedure consists of removing two centimeters of polymer in each fiber end, and realizing an orthogonal cut to the fiber axis, right in its end. After being carefully cleaned with a clean cloth and acetone each of these ends, it can be verified through the camera of the optical fiber splicer machine. Once prepared fibers, they are placed in parallel way, within the fusion chamber of the splicer machine, so that the electrical arc is applied to them, as is shown en Fig. 2.
2.2. Installation of the pair of optical fiber ends in the electrical arc
As experimental installation was used the chamber of fusion of the optical fiber splicer, Fitel mark, whose loss record per splice is of 0,01 dB to monomode fiber, each splice can be realized in a lapse of 13 seconds approximately. The optical fiber splicer is a machine that radiates electrical arcs whose electric power are of 20 W to splice fiber monomode, and 40 W to splice fiber multimode. In this application microsensor was made with monomode optical fibers. After cleaning carefully with acetone the optical fiber ends, these are installed in parallel in the fusion chamber of the splicer machine, in such a way that the pair of fiber ends is tied and right where the electrical arc will form. This task is not easy the first times, but with a little practice and care, it is routine and effective. Fortunately the system of the splicer has control of axial micropositioning with which the point can be chosen where it is desired to apply the discharge in pair of fiber ends.
2.3. Formation of the semidrop: formation stages
In order to obtain the required optical results with the microsensor, it is very important to obtain the form or model of the semidrop. As all artisan work is necessary to have a serious dominion and knowledge on the operation of the splicer machine, to have absolute control on the final physical form that we wished to give our microsensor. In order to explain the form in which east microsensor of optical fiber was micromachined, we have planned to break down this process into three main steps: fusion of the ends, getting the preform, and obtaining semidrop. These parameters are described in detail, as follows:
2.3.1. Fusion of the ends
Properly placed the fiber ends, as it was explained previously, the discharge of the 20 W electrical arc is practiced automatically, by a lapse of 13 seconds approximately. The place where the electrical arc is due to apply is just, at the end of the pair of ends, as is shown in the Fig. 2.
This application has like objective realizing a union that fixes both fiber ends. By means of the application of this electrical arc, the pair of fiber ends reaches the temperature of 1900 C melt merging and reached a preliminary part of the fiber end with the other, as shown in Fig. 3.
2.3.2. Obtaining of the preform
After the first electrical discharge to have realized, the pair of fiber ends has been fused partially. The following discharging, of the same characteristics, is applied right in the region interface fused fiber-fiber, as it is in the Fig. 4. The objective of this discharging is to approximate the preform obtained towards the physical model of the semidrop.
This is obtained by means of positioning again the pair of fused fibers, just where the discharge will appear, see Fig. 5. 20 W electrical power by 15 seconds is applied after the discharge place has been chosen. Therefore, the following preform of the microsensor has being obtained.
Note physically, the semidrop is already shaped and this stage is called the microsensor preform, see Fig. 6, but is necessary to provide one more a discharging to homogenize, in liquid face, the distribution of refractive indices in the region of the semidrop, to ensure that the microsensor will have a transmittance of not more than 30 dB for the visible or IR region in contact with the air.
2.3.3. Obtaining of the semidrop
The last discharging is applied, just in the curved zone of the preform, as is in the Fig. 7. This discharging also is of the same characteristics, that the previous ones. In this last application, because the fusion temperature in the region of the semidrop is reached, the splicer machine is due to have in an advisable position to attenuate the effect of the gravity force during the application of the electrical arc, and thus to avoid a deformation in the semidrop geometry.
After the electrical discharging applying, Fig. 8, the final conformation microsensor is obtained with the form shown in the Fig. 9. Final dimensions are width 250 μm, and thickness 125 μm.
3. Physical description of the optical fibermicrosensor
The optical fiber microsensor is constituted by a pair of parallel optical fibers, where one of the ends of both fibers are joined by controlled electric arc melting, forming a glass semigota, the remaining two fiber terminals work as input and output ends, see Fig. 1. The fibers used are step index, whose core and cladding diameters are respectively 8,3/125 microns, these fibers are commonly used in optical communications, for a wavelength of 1550 nm. The optical fiber microsensor has a transmittance function or transmitted, this function indicates the optical filter response imposed by this microsensor dependent on wavelength, and refractive index of the liquid tested. The optical fibers when transmitting perfectly in the 1550 vicinity nm, do not present attenuation in the region of the microsensor that corresponds to fibers.
Nevertheless, the microcavity formed in the fused ends, by its dimensions, geometric, wavelength, and the refractive index of external means,
In the region of interaction of the semidrop, the microcavity or semidrop constitutes to incident medium (glass), and to medium of transmission it constitutes external means. The reflective properties of the semigota- surrounding medium interface, are regulated by the coefficients of Fresnell, which are not evaluated due to the limitations that impose the dimensions of the microcavity, nevertheless for experimental intentions is advisable to determine the transmittance of the fiber microsensor,
4. Theoretical model of the performance of the optical fibermicrosensor
The theory of operation of the fiber microsensor starts off of the fact that each pair of immiscible liquids owns its respective refractive indices:
Since the optical power of input,
Since for each one of the immiscible liquids, including the air, corresponding output voltages,
Considering that the guarantee to operate to the microsensor with two average immiscible liquids, is that thetransmittance differences are
Sensitivity to both immiscible liquid refractive index,
where,
with respect to the rapidity of commutation of the microsensor, this property rests in the bandwidth of the photodetector used in the microsensorial system. Nevertheless in theoretical terms, the rapidity of commutation,
where,
where BW is the bandwidth of the photodetector.
5. Experimental results and discussions
Like a pair of immiscible liquids, it has been selected to oil and to the water, by the importance that it has in the economic growth in the world. In this work it was investigated firstly, the effect of the state of polarization of the electric field to the input of the fiber microsensor on the voltage induced in the photodetector,
According to Eq. 2, the voltage that appears in the photodetector, Vphoout, does not have to depend on the polarization of the incident electric field to the microsensor input. However in the interface semigota-liquid, reflections of Fresnell take place, where the polarization of the incident beams is polarimetrically influenced by the characteristics of the same. In order to verify experimentally, that the voltage that appears in the photodetector, Vphoout, is independent of the polarization, it was made vary the state of polarization of the field,
When varying the angular position of the coil modifies the angular inclination of state of linear polarization of the field,
It is appraised that the voltage that appears in the photodetector,
In order to research the corresponding transmittances for each interaction medium:
The experimental scheme used to obtain the output spectra is shown in the Fig. 14. The output spectra are useful to determine the functions of transmittance of the microsensor corresponding to each surrounding mediums, according to Eq. 1, for each refractive index
The Fig. 15 shows to the value of transmittance functions for each system semigota-water, semidrop-air, and semidrop-oil, in the region of the 1500-1600 nm. These functions are standardized with respect to the transmittance spectrum of the system semidrop-air, which presents the higher peak of transmission in 1527 nm, and it is different from zero from 1508 nm to 1560 nm. The transmittance spectrum of the system semidrop-water presents a peak in 1522 nm, and it is different from zero from 1515 nm to 1560 nm. The transmittance spectrum of the system semidrop-oil is equal to zero from 1500 nm to the 1600 nm. Reason why to distinguish oil of air, is propitious to use wavelengths in the 1508-1560 nm range, and to distinguish oil of water, is propitious to use wavelengths in the 1515-1560 nm range. Nevertheless, to discriminate the water of oil, the spectral region that offers this possibility, we divided it in two: the one of low contrast, and the one of high contrast. The one of low contrast begins from 1500 to 1515 nm, and from 1534 nm to 1562 nm, as it is possible to be appreciated in the Fig. 15.
The spectral region of high contrast begins from 1523 nm to 1534 nm. This procedure ensures the success of operation of the optical fiber microsensor, and it is attainable for any other pair of immiscible liquids of industrial or biomedical interest.
Remarkable contrast exists in the values of
When submerging the microsensor towards oil, was observed a reduction to 0,0% of the la
In order to demonstrate the effectiveness of microsensor of fiber for the detection of the interfaces formed by immiscible liquids, the graph shown in the Fig. 17 was developed. In this graph the changes of transmittance acquire knowledge that detects the microsensor of fiber, when realizing an orthogonal sweeping, from the bottom towards the surface, crossing the interfaces that form in a tank cistern that contains interfaces water-oil,,
It is observed that in these levels, a commutation in the transmittance of the fiber microsensor happens, that is interpreted like the existence of each of these interfaces that appear in the axis of
To researchthe sensitivity ofthe optical fiber microsensor, referredto Eq. 7, whichrequiresthe information specified inTable 1,andtheindicesof refractionof water1,3,oil 1,48, and air 1,0. Notein Table2, thefibermicrosensorhasahighsensitivitytocrossthe air-oil, becausethechangeoftransmittanceisfrom 1,0to0,0, forasmall variationofrefractive indices.Inthecaseofoil-waterinterface, transmittancevaluesare veryclose, astheirrefractive indices, sothat thesensitivity offibermicrosensorsuffersa significant reduction.
Surroundingmedium | T(n) to 1550 nm, (%) |
air | 100 |
water | 18,5 |
oil | 0,0 |
Interfaces | S(Δn) |
water-oil | 1,0 |
oil-air | 2,0 |
With a similar procedure and by using a white radiation source (light emitting diode of high brightness) and a silicon photodetector, gives the percentage values of
Surroundingmedium | T(n) to 390-780 nm, (%) |
air | 100 |
water | 13 |
oil | 20 |
Like any proximity sensor device, the optical fiber microsensor when passing the interface of air, oil, and water, indirectly reports the location of the interface, by location or area of switching their output voltages: H (high) or L (low). Knowledge of minimum time, that the microsensor can resolve a change of medium, is of importance to the location of the interfaces of immiscible liquids. The switching speed of the microsensor is strongly restricted by the bandwidth of the photodetector to the optical output of the microsensor (13 kHz). Under this, to know the response time of the microsensor, it applies the criterion of rise time, tr, (risetime) with respect to bandwidth of LTI system, which in this case is the bandwidth, BW, of InGaAs photodetector. The relationship applied in this deduction is for Eq. 9, so that, tr = 26,92 µm. Finally, the finish of fiber optic microsensor is shown in Fig. 18, and specifications of optimized optical fiber microsensor are shown in Table 4.
Elements | Characteristics |
Optical fibers | 8,3/125 μm |
ILD | 1550 ± 0,5 nm |
Power range | 5 mW – 6,5 mW |
Photodetector | Si low power, BW= 1,75 MHz |
Max. response time | < 2 μs |
Dynamic range | Refractive index < 1,9 |
Sensitivity | - 5,714 x 10-4 μV, water-oil |
Temperature | 0° a 50 °C |
6. Conclusions
This research has shown that the fiber optical microsensor is possible to manufacture by electric arc technology. We demonstrated that is possible to improve the response detection of optical fiber microsensor, for certain immiscible liquids, by proper choice of a specific wavelength. This wavelength or radiation spectral region should provide a high discrimination of the two liquids. Speed detection of the microsensor, strongly dependent on the bandwidth of the photodetector. The method used in this research can be applied in the detection of other mediums, including other regions of the optical spectrum. Due to geometrical and physical properties of fiber microsensor, it can be applied to biomedicine, because it is micrometer-scale, flexible like being guided in an artery or a catheter inserted, and it is easy to sterilize. As future research work, we have considered using the microsensor to implement a system of characterization and recognition of organic and inorganic liquids (alcohols, acids, neutrals, blood, urine, water, etc.) by using spectroscopy in the infrared and/or visible region. Optical fiber microsensor represents an alternative in the industrial applications, and mainly in the detection of explosive, corrosive and/or highly harmful liquids, for the human being.
Acknowledgments
We are thankful to the Benemérita Universidad Autónoma de Puebla, and the group of full professors of the Facultad de Ciencias de la Electrónica, Optoelectronic department, by to have looked for at the time, the ways and possibilities, to acquire these efficient equipments of measurement, to have been able to make reality this project.
References
- 1.
De Leon V. . Khotiaintsev S. 1996 Raytracing in the design of microoptical sensors used for the determination of refractive index of surrounding media.,Infrared Spaceborne Remote Sensing IV,2817 299 311 ,978-0-81942-205-7 Denver, CO, USA, 1996 - 2.
Jones O. C. Zimmer G. A. 1978 Optical probe for local void fraction and interface velocity measurements, ,49 8 (August 1978),1090 1094 ,0034-6748 - 3.
Molina-Flores E. et al. 1995 Fiber-optic multipoint high-resolution level-sensor for biomedical applications. Proceedi ng of SPIE, Medical and Fiber Optic Sensors and Delivery Systems,2631 121 126 ,978-0-81941-995-8 Barcelona, Spain, 1995 - 4.
(2006).Microsensorrefractométricodiscreto de fibraópticaparadetección de interfaces petróleo-agua, operando en la región visible,Molina-Flores E. Aguilar-Jiménez O. Molina-Flores D. (2006 4 4 3 (December 2006),815 826 ,0188-6150 - 5.
(2002).Novel optical fiberrefractometric transducer employing hemispherical detection element, ,Svirid V. Khotiaintsev S. Swart P. L. (2002 41 41 4 779 787 ,0091-3286 - 6.
Volodymyr S. Khotiaintsev . S. 2000 Optoelectronic multipoint liquid level sensor for light petrochemical products,,4148 262 268 ,978-0-81943-795-2 2000