Thermal and electrical properties of the materials used in the model.
This chapter deals with heat transfer challenges in the microdomain. It focuses on practical issues regarding this matter when attempting the fabrication of small footprint thermoelectric generators (μTEGs). Thermoelectric devices are designed to bridge a heat source (e.g. hot surface) and a heat sink (e.g. ambient) assuring that a significant fraction of the available temperature difference is captured across the active thermoelectric materials. Coexistence of those contrasted temperatures in small devices is challenging. It requires careful decisions about the geometry and the intrinsic thermal properties of the materials involved. The geometrical challenges lead to micromachined architectures, which silicon technologies provide in a controlled way, but leading to fragile structures, too. In addition, extracting heat from small systems is problematic because of the high thermal resistance associated to heat exchanged by natural convection between the surrounding air and small bare surfaces. Forced convection or the application of a cold finger clearly shows the usefulness of assembling a heat exchanger in a way that is effective and compliant with the mechanical constraints of micromachined devices. Simulations and characterization of fabricated structures illustrate the effectiveness of this element integration and its impact on the trade-off between electrical and thermal behavior of the active materials in device performance.
- silicon technology
- silicon nanowires
- heat exchangers
It is quite evident that extending or improving human senses has enabled human societies to prosper by acquiring information from their surroundings and gaining knowledge from it. Internet of Things (IoT) embody this trend today combining distributed sensing with high connectivity so that wise decisions and actions follow information gathering and analysis [1, 2]. Trillion Sensors is another paradigm onto which IoT is further exploited on the basis that the more extensive or intensive the deployment of sensor networks is, the more fruitful the knowledge that can be derived from them would be [3, 4].
Small dimensions (nanometers to micrometers) are appropriate in the sensitive part of sensors when they need to interact with phenomena or entities equally characterized by such small dimensions (light, molecules, living cells…). An overall small size for the sensors themselves is not devoid of interest either. The smaller they are, the more sustainable their fabrication is in terms of materials and energy, and the more cost-effective they become. Small size is also enabling in itself, e.g. medical implants, as well as convenient, e.g. payloads.
Sensing requires energy. A certain provision of energy autonomy is needed for sensors to be deployed in remote locations, harsh environments, or where they need to remain temporary unattended. Batteries is a common way to provide such autonomy, but their charge is finite impeding long-term autonomy scenarios. Moreover, their recharge, replacement and disposal imply a logistic and environmental burden that will not be affordable when IoT gets to its full extent mobilizing tens of billions of devices and an even larger number of sensors.
Secondary batteries can be kept recharged by coupling them with energy harvesters able to draw energy present in the environment . Heat is abundant in natural scenarios, and waste heat is also abundant in human-made scenarios due to laws of thermodynamics and our profuse use of thermal machines. When such heat gives rise to temperature gradients (a situation as simple as a hot surface exposed to air), thermoelectricity is a convenient way to extract electric energy from them [6, 7].
For that extraction to be optimum, the external thermal gradient needs to be fully transposed into the thermoelectric generator itself. Physical interaction of small devices with their environment may exploit profitably some scale factors when going down in dimensions, but, sometimes, small sizes pose a handicap or challenge for such interaction, too. This is the case when trying to cool down locally a part of a small device by exchanging heat with the surrounding air. This chapter tries to illustrate this point by sharing the issues and strategies the authors have dealt, and are dealing with, in their quest for silicon-based miniaturized thermoelectric generators.
2. Silicon-based thermoelectric generators
Silicon technology has been developed around an enabling and highly abundant semiconductor material. It is a mature technology apt to mass-production of devices with economy of scale and it is the champion technology of miniaturization. Not surprisingly, it boosted microelectronics in the XX century and nanoelectronics in the XXI century. In addition to the set of techniques that allow the fabrication of integrated circuits by depositing and patterning thin films on a silicon wafer, silicon technologies also developed micromachining techniques that allow carving and shaping the silicon wafers into structures that are able to interact with the environment. Sensors and actuators belong to the latter category. Since energy harvesters are environmental interacting devices and, application-wise, they should not be much larger than the sensors they will feed, it is only logical that their fabrication will similarly benefit from the silicon technologies toolbox. These technologies do not only excel in miniaturization but also in
2.1 Micro thermal device architecture
The traditional thermoelectric generators mentioned above feature a π-architecture, where the π symbol gives a visual clue about how each thermocouple is built assembling vertically two semiconductor pellets (
Silicon technologies are of planar nature. They enable massive parallelism at
The main objective when defining the architecture and the technological route for a
The platform consists of a thin silicon area fabricated by eliminating the silicon beneath it. In order to preserve its thermal isolation from the surrounding bulk silicon, the physical connections between them should be minimized. Such connections are the mechanical supports that keep the platform in place (e.g. ancillary silicon bridges) and the thermoelectric materials themselves (and whatever supports they may need). In order to minimize the thermal conduction of these elements, they must be produced with
Figure 1 shows the schematics for such a device. Any hot surface in which this device is placed will act as a heat source. The top surface will be exposed to air acting as heat sink and will exchange heat with it. Due to their different thermal mass, the bulk rim area will hardly cool down, thus being the hot part of the device, while the platform will experience a larger decrease of temperature becoming the cold(er) part of it.
With respect to the thermoelectric material, the depicted device follows a uni-leg approach. Two thermoelectric materials are still at play, but a metal one replaces one of the semiconductor legs in order to close the circuit. Some thermoelectric performance is sacrificed because metals behave poorly thermoelectrically (they have higher thermal conductivities and close to zero Seebeck coefficients), but for the architecture presented and to keep processing simple, the use of a metal leg is technologically convenient.
Regarding the semiconductor thermoelectric material, one distinct feature of our approach is resourcing to silicon materials, namely arrays of silicon nanowires (Si NWs). The rationale behind this option is to attempt the fabrication of
Moreover, arrays of Si NWs can be conveniently grown as a post-process using a
The metal leg cannot be integrated in the same self-standing way. It is deposited as a thin film, so it needs a physical support. These ancillary supports need to be thermally optimized since they bridge the hot and cold areas. The nature of these supports has evolved across the different generations of our devices: from long and thin silicon bridges (400 μm x 100 μm x 15 μm) to wide and very thin Si3N4 membranes (100 μm x 1000 μm x 0.3 μm). Since thermal conductivity of Si3N4 is two orders of magnitude lower than the one of silicon, there is a net gain in thermal conductance, while enabling a shorter and wider (and less electrically resistive) metal leg.
The thermal impact on platform isolation of the
As said, longer NWs generally imply larger ΔT and, thus, a larger thermovoltage. However, a resulting larger voltage is not necessarily associated to a larger power. Power (
It must be noted that the heat transfer issues discussed in this chapter revolve about the challenge of exchanging heat in planar micromachined structures exhibiting very small exchange surfaces [18, 19, 20, 21, 22], while the particular nature of the thermoelectric material employed (e.g. NWs) is of no significance: the same conclusions will apply if silicon membranes, silicon-based thin films, or any other thermoelectric films of interest were considered instead.
2.2 Optimization considerations (load matching)
When considering the optimum design for a thermoelectric microgenerator (μTEG) the generated power is the parameter which needs to be maximized. It is well known that for a given μTEG with its own internal resistance, the power that is transferred to the load is maximized when the internal resistance and the load resistance are equal. This case is usually known as load matching condition .
Considering the electrical circuit diagram shown in Figure 2, which represents a μTEG, formed by a voltage source (VOC) and its internal electrical resistance (RTEG), connected to a load resistance (RL), it is straightforward to evaluate the total dissipated power at the load as:
Finding the value of RL which maximizes PL implies after a few calculations the load matching condition, RTEG = RL. It is important to notice that the only parameter allowed to change in this optimization is the load resistance. Therefore, one can write the maximum power as:
As can be seen in Figure 3, where the output power of a μTEG is plotted versus load resistance for three different internal resistances, each curve has a maximum for the load matching condition. But now the influence of the internal resistance is highlighted, where the lower its value, the greater the power output. In Figure 3, for example, halving the internal resistance can double the power output at the load matching condition. This highlights the importance of reducing the internal resistance when designing a μTEG.
Some publications discussing load matching focus on the need to modify the internal resistance, increasing it, in order to match the load resistance . According to Figure 3, this is in fact an error. It is always a better approach to minimize the internal resistance in order to increase the power output even further. Once the internal resistance is the minimum possible, then the load matching condition can be applied to maximize the power output. Actually, many integrated circuits exist which efficiently implement maximum power point tracking (MPPT) algorithms to extract the maximum power from a power source by modifying its load resistance.
This load matching approach can be analogously applied to the temperatures involved in the μTEG and is known as thermal matching. A simplified conductance network describing the μTEG (KTEG) in parallel with KLK accounting for parasitic thermal leakages and in series with KS representing the conductance to ambient (to both heat source and heat sink) is shown in Figure 4.
To explore which is the KTEG value that maximizes Pmax, as was done in the electrical case, Eq. (2) can be rewritten as:
Where ΔTA is the total available temperature difference, Tamb-Thot. KTEG is the internal thermal conductance of the μTEG and KS represents the thermal conductance to the ambient.
When decreasing RTEG, as deemed appropriated in the previous paragraphs, it is important to keep in mind that KTEG is bound to increase, as they are inversely proportional. This is because of the implicit assumption that changing KTEG implies a geometry modification, not a material property change and the geometry change affects both electrical resistance and thermal conductance of the μTEG. Ignoring any leakage contribution (KLK = 0 W/K) in Eq. (4), the power output (solid) and ΔT (dotted) versus KTEG can be seen in Figure 5. Three different KS cases have been considered to highlight the fact that, the larger KS, the larger the power output, even for a constant KTEG. It can be seen that when KTEG = KS, the maximum power condition when KLK = 0, then the temperature drop across the μTEG is 50% of the available temperature difference.
Similar to the electrical case, many papers discussing thermal matching focus on reaching a temperature drop in the μTEG equal to the temperature drop across KS [5, 24, 25]. When this KS represents a heat exchanger, some authors suggest a low KS heat exchanger to match KTEG and therefore maximize the power output according. While this approach assures operation at the mathematical local maximum for a given KS, it is a bad practice because it ignores the absolute maximum, which takes place at larger KS values for a given KTEG.
Looking at Figure 5, if KTEG = 1 W/K, this reasoning would imply that KS = 1 W/K would be necessary, and 50% of the total available temperature difference would drop across the μTEG. However, with a better heat exchanger, KS = 10 W/K or even KS = 100 W/K, then ΔT will asymptotically approach ΔTA, and the power output will asymptotically reach:
In conclusion, both load matching and thermal matching are conditions that are mathematically true, but from a practical point of view, care must be taken when designing a μTEG to maximize its power output. First of all, its electrical internal resistance (RTEG) must be minimized, and after that, power output can be maximized by connecting a load which matches that of the μTEG, or simply an IC implementing an MPPT algorithm. On the thermal side, as RTEG is minimized, the thermal conductance (KTEG) is consequently maximized. Then, as the μTEG is already optimized, and it is not possible to further increase KTEG, the only option is to act on the external components, which in this case is the heat exchanger, and to choose one with an as large as possible KS, so that almost all of the available ΔT will be internally transferred to the μTEG.
3. Decreasing the platform thermal resistance
As mentioned before, the performance of μTEG devices depends on the temperature difference ‘seen’ by the thermocouples. Therefore, minimizing thermal resistances in series with those elements would improve the performance of the device. In this section, such improvement is demonstrated by decreasing the thermal resistance between the suspended platform and the ambient, usually the cold part, by favoring the heat flow locally. Two methods have been used to increase such heat exchange: (i) by forcing heat convection onto the platform and (ii) by contacting it with a cold mass. The promising results obtained from the experiments described in the next two subsections call for optimizing this effect through the development of a procedure to integrate a heat exchanging structure, which will be shown in section 4.
3.1 Forced convection experiments
As the working scenario for the μTEG devices is dominated by a temperature difference between the hot and the cold parts, heat convection could play also an important role on how these temperatures are established. Convection is a mechanism of heat flux originated from the movement of the surrounding fluid, which will be typically air for the usual applications of the presented devices. Depending on how this movement is induced, convection can be classified as natural or forced.
Natural convection is based on the warming up of the air that is close to a heat source that, due to the lowering of its density, tends to move upwards, giving its place to colder air and so promoting the heat exchange. In forced convection, air is forced to move and then renew by an external force.
In order to demonstrate the improvement in the performance of the device, three different sets of experimental measurements have been performed on a device at three different convection conditions. The first one corresponds to natural convection, which occurs when the device is operated by letting it rest on top of a hot surface exposed to ambient at room conditions. The second and third sets of measurements correspond to forced convection regimes. In the second case, this is accomplished by the use of a standard CPU fan (see Figure 6) placed over the device, while in the third, an air jet, obtained through a syringe connected to the compressed air line in the laboratory, is directed towards the device. More details are available at .
Such experimental measurements have been performed on two different devices, featuring 30 and 60 μm long silicon NWs (by filling 3 and 6 trenches as described in section 2.1). Consequently, each one of the devices has different electrical and thermal resistances.
The obtained experimental results are shown in Figure 7. The devices have been measured at different temperatures of the hot plate (from 50 to 200 °C in 25 °C steps).
The measurement results show a very clear improvement in the performance as a result of forced convection. The maximum output power obtained when the device is mounted under the fan is multiplied by 3 when compared with the natural convection regime, while when under the more directed and higher flow air jet, the performance increases nearly three orders of magnitude: from a few nW to almost 0.7 μW. Moreover, the more performant air convection is, the less relevant become the thermal properties of the thermoelectric material. In natural and air forced convection cases, the larger output power corresponds to the longest nanowires, whereas in the air jet forced convection the opposite is true. This happens because the longer nanowires also have a larger electrical resistance, and its larger thermal resistance is not significant in this case where the platform to ambient thermal resistance is enough to assure a large ΔT.
3.2 Cold finger approach
In the previous subsection, it has been experimentally demonstrated how important a good thermal connection with the surrounding ambient is in order to improve the overall performance of μTEG devices. Nevertheless, forced convection scenarios are not always available and artificially forcing them needs additional energy consuming devices. Therefore, in order to explore a passive strategy to diminish the thermal resistance to the surrounding ambient, the effect of contacting the microplatform with a metallic probe has been assessed. With this experiment, the feasibility of the addition of a heat exchanging structure as a general strategy for the reduction of the thermal resistance to the ambient will be demonstrated.
The experimental setup consists of a metallic probe dipped in thermally conducting paste, which is carefully positioned on the micro-platform by the use of a micro-manipulator.
The performance improvement obtained by means of this approach can be observed in Figure 8, which shows a plot of the Seebeck voltage output of the device placed on a hot plate at 150 °C when the cold finger is being attached. It can be observed that the voltage increases rapidly after contact, and it rises even more when the applied force to the cold finger is increased slightly, so demonstrating the reduction of the thermal resistance when the physical contact is improved.
In Figure 9 the power curves obtained from the same device at a hot plate temperature of 250 °C with and without the cold finger are shown. It can be seen an important improvement in the performance of two orders of magnitude, from 1.3 to 142 nW, so proving the effectiveness of the cold finger approach as a proof of concept validating the further development of more effective heat exchanging structures.
4. Heat exchanger
The previous section highlights the importance of physically contacting the platform in order to improve heat extraction, and thus cooling it more efficiently. According to section 2.2 and the results shown in section 3.2, the need for a heat exchanger has been proven. In this section, we study the implementation of such component on the μTEG. This poses several problems from the technological point of view, especially considering the starting device architecture used to expose the thermoelectric material to a thermal gradient. The thermally isolated platform is a fragile structure and physically contacting it without caution might break it. A proper methodology with auxiliary components needs to be developed components to provide such contact safely.
The approach implies to have a thermally conductive piece contacting the platform and interfacing this part of the device with a heat exchanger of appropriate size. For this reason, such piece will be dubbed as ‘adapter’. The contact needs to be compliant to absorb any excess vertical displacement with deformation. The compliant part of this contact will be a certain amount of silver paste. A rigid spacer (PMMA), sitting both on the silicon bulk rim and the platform, will also be necessary to limit the maximum excursion of the adapter over the platform so that pressure between the heat exchanger on top and the platform below can be applied in a safe way. Finally, the heat exchanger itself, a commercial one of similar footprint is assembled onto our chip. In this case, our chip is 7x7 mm2 and the smallest commercial heat exchanger found is 8x8 mm2. A PCB with a through-hole, to insert a copper plate improving the thermal conductance from the hot surface to the bulk silicon rim, and a slightly larger partial etch to fit the chip and facilitate the wire bonding to auxiliary copper traces, are included in the assembly as shown in Figure 10.
4.1 Modeling results
The feasibility of the approach has been first tested building a physical model and solving finite element simulations (COMSOL) to evaluate the expected improvement on performance. The thermal and electrical properties of the materials used in the model are listed in Table 1.
|κ (W·m−1·K−1)||σ (S·m−1)||S (V·K−1)|
|Silicon NWs||25 (1)||12·103 (1)||250·10−6|
The model boundary conditions include a constant hot temperature at the bottom (Thot = 100 °C) and natural convection on the vertical and horizontal walls of the heat exchanger through a heat exchange coefficient directly calculated in COMSOL for an air ambient temperature of 27 °C. When such element is not present, the heat exchange coefficient is applied directly on the platforms surface. Figure 11 shows the temperature distribution for the whole model under such conditions. As it can be seen, even with a heat exchanger, the lowest temperature reached in the cold part is slightly below 70 °C although the ambient temperature is 27 °C. This is because the thermal resistance from the heat exchanger to the ambient is approximately one third of the total thermal resistance while the thermal resistance from the bottom of the PCB (actually most of this is from the silicon chip) to the heat exchanger is approximately two thirds of it.
The internal temperature distribution for chips with four platforms with NW lengths of 10, 20, 30 and 40
On the other hand, for the case without heat exchanger (left), the temperature differences across the nanowires do not reach beyond 2 °C. In this case, the thermal resistance to the ambient is much larger than the nanowires thermal resistance, and a very small temperature drop develops across the active thermoelectric material.
If the temperature solution from the finite element model is coupled to an electrical model through the Seebeck coefficient of the nanowires, the I-V curves and power output for each platform considering both scenarios can be obtained.
These results are shown in Figure 13, where the power output has been plotted as power density considering a device area of 2 mm2, large enough to contain the whole platform (approximately 1 mm2) and space for additional contacts.
Clearly, a much larger power is obtained when the heat exchanger is in place due to the much higher ΔT perceived by the NWs. In addition, the behavior of the four platforms evolve differently. Without the heat exchanger, voltage and power scale with the length of nanowires since their thermal resistance is the dominant part of the total device thermal resistance and such length is directly determining the attained ΔT. However, when the presence of the heat exchanger secures most of ΔT, the positive effect of the lower thermal conductance of longer nanowires, which is still there, rapidly saturates and even reverse (see T4 vs. T3) because the detrimental impact of the increasing electrical resistance becomes dominant.
4.2 Manual assembly and impact on measurements
The significant increase in the generated power when applying a forced convection or a cold finger and the results from the simulations including a heat exchanger directed our efforts to the construction of the previously described heat exchanger assembly on our μTEGs (see Figure 10).
The preparation sequence of the required components is given in Figure 14a. A heat exchanger adapter is made from four Cu wires (one per on-chip a device), with diameter similar to the size of the suspended platform (which they will contact after the assembly) inserted in a square brass piece and machined to the appropriate length. The tips of the wires are dipped with thermal paste (Figure 14b) to fill the gap between the Cu wires and the suspended platforms to guarantee good thermal contact (Figure 14c). A PMMA spacer with a thickness appropriately matching the length of the protruding Cu wires is then assembled between the heat exchanger adapter and the μTEG, and finally, the aluminum heat exchanger is placed on top of adapter using a thermal paste (Figure 14d). Further details can be found in  from which Figures 14–17 have been adapted.
Through the described integration scheme, a first evaluation of the performance improvement brought by a heat exchanger to the μTEG is enabled. In this study harvesting measurements with and without heat exchanger were performed by placing the assembled devices on a Linkam THMS 350 V heating stage at various temperatures in a natural convection environment. Three different cases were measured: without heat sink, with heat sink and with heat sink + pressing, where for the latter a force is applied on top of the assembly to reduce the thermal resistance of the thermal paste. Chips with different thermoelectric materials were measured: Si NWs, Si-Ge NWs and Si microbeams. At the current stage of technology maturity, a rather low number of devices has been measured, but the results shown in the next subsections correspond to significant devices of each category. In terms of measurement uncertainties, the most important source are thermal fluctuations that due to the thermoelectric nature of the device introduce variations in the measured V and I, which have been estimated to be below 10 μV and 1 μA, respectively.
4.2.1 Measurements with Si NWs
The Seebeck voltage vs. hotplate temperature curves for the Si NWs-based μTEGs with different number of trenches are shown in Figure 15. As anticipated, all the devices presented output voltages that scaled with the number of trenches (i.e. length of NWs). However, the reduction of the thermal resistance between the cold side (suspended platform) and the ambient when a heat exchanger is integrated resulted in a large increase of ∆T across the NWs and hence higher overall voltages.
In terms of power, the maximum power densities obtained at hot plate temperatures of 100 °C without the heat exchanger were in the range of 0.05–0.1 μWcm−2. As expected, a tremendous increase in power density was observed after the integration of the heat exchanger + pressing, and values in the range 7–42 μWcm−2 were observed. No clear trends were observed with the number of trenches.
4.2.2 Measurements with SiGe NWs
For devices with SiGe NWs, considerable higher Seebeck voltages were observed when compared to Si NWs (Figure 16), due to the higher thermal resistance resulting from the lower intrinsic thermal conductivity of the former. With and without heat exchanger, the devices performed better with increasing number of trenches. Also, power densities rose considerably with the integration of the heat exchanger. As already observed for the Si NWs, the voltage and generated power improved further when a slight pressure was applied to the heat exchanger, It is worth noticing that the maximum power thus obtained does not differ much for Si and SiGe NWs: 41.6 μWcm−2 vs. 45.2 μWcm−2, respectively, considering a T3 device on a hotplate at 100 °C. This points to the dilution of the effect of better starting thermal properties when the heat exchanger is present.
4.2.3 Measurements with Si microbeams
Si microbeams devices were fabricated to compare the performance of bulk Si with Si NWs. After the integration of the heat exchanger + pressing, the results presented in Figure 17 show a remarkable three orders of magnitude increase in the generated power from ∼650 pW to ∼690 nW for a T1 device, i.e. from 32.5 nWcm−2 to 34.5 μWcm−2. This result evidences again that once the heat exchanger is in place, the thermal properties of the thermoelectric material become second order. Hence, by optimizing their electrical properties and ensuring a good ∆T with the aid of a heat exchanger, it is possible to obtain high power densities even with high thermal conductivity thermoelectric materials such as Si microbeams.
4.3 Semiautomatic assembly with integration density
In order to translate the promising power densities of a single structure into useful absolute power levels, a certain number of thermocouples needs to be integrated and connected. The μTEGs design was modified to attain a higher integration density by reducing the number of active sides. The new thermocouple has a rectangular shape with one side featuring the membrane providing mechanical support and metallic connection, and the opposite side composed of the trenches to be filled with NWs. In Figure 18, a 3D schematic of the new unitary thermocouple is shown. The same cross-section profile of Figure 1 still applies. With this new design, many elements can be integrated in the same chip: up to fifty thermocouples (each with an approximate size of 5 x 0.6 mm2) fit in series or series–parallel configuration in a 49 mm2 chip, as shown in Figure 19. Both configurations would lead to the same harvested power, but the series one will scale up voltage while the parallel one will scale up current.
This compact design requires new components and a novel and more efficient approach for the integration of the heat exchanger in order to boost their thermal performance. A micromachined Si adapter (substituting the Cu wires, brass plate and PMMA spacer of the previous section) is necessary for the distribution of the force exerted on the platform by the heat exchanger, and different designs featuring the corresponding serial or parallel arrangements were fabricated. Figure 20 (left) depicts the Si adapter designs where the central columns contact the platform of each thermocouple in the chip and the ones at the corners act as force distributers. Similar to the previous section, a commercial Al mini heat exchanger will be placed on top of the Si adapter to help the circulation of heat from the Si rim of the μTEG (warm side) through the thermoelectric material to the platform (cold side) to achieve the desired larger ΔT. The heat flux representation through the assembly is shown in Figure 20 (right).
To achieve a good thermal contact, which is key for a maximum generated power, a thermal interface material (TIM) needs to be placed between the thermocouple and the adapter. To this aim, an inkjet printer (Dimatix) was chosen to deposit a controlled amount of TIM only on the columns of the adapter.
After dispensing the TIM, the adapter is placed face-down onto the thermocouple chip already wirebonded on a PCB. This is done with the help of a pick & place machine (Finetech) that enables proper chip alignment and attachment with a controlled gentle force (0.1 N). A holder with a removable lid for the adequate handling of the Si adapter during the process has been designed and 3D-printed. It allows accessing the corresponding side of the adapter, first to the inkjet printer, and then to the pick & place machine. The whole assembly process is depicted in Figure 21.
This is a still ongoing process. Two different inks are being tested to act as TIM between the adapter and the suspended platforms: a conductive silver nanoparticle ink (Agfa Orgacon SI-J20X) and a SU8 based polymeric ink (Micro Chem Prielex). The tests involve the assessment of the adequacy of the viscosity and adhesion of the TIM and the evaluation of the endurance of the μTEGs platforms during the assembly. Other TIM materials already used for the mainstream attachment of heat exchangers onto microprocessors can be also evaluated, as well as other ways of locally dispensing them, such as stamping. In any case, the goal is to obtain an integration route for the heat exchanger, without which no workable ∆T would be possible in such miniaturized devices, that is prone to the automatic handling of the involved chips and it is compatible with their dimensional and mechanical endurance constraints.
With this chapter, the authors have tried to show the challenges to sort out when fabricating microgenerators (μTEGs) with planar silicon technologies. Such technologies offer a cost effective way of mass-production of miniaturized devices. However, the very nature of such technologies, the high thermal conductivity of bulk silicon and the typical thickness of the layers involved advises using silicon micromachining to enable areas of lateral thermal contrast. Such transversal architectures helps to translate naturally occurring vertical thermal gradients into internal lateral ones. In this way, a temperature difference will develop across a horizontally and self-standing laid thermoelectric material whose length is a design parameter. A material properties trade-off ensues: the longer the material, the higher its thermal resistance, increasing the attainable ΔT and the obtained Seebeck voltage, but the larger will be its electrical resistance, reducing the power obtainable from that voltage. In addition, it has been shown that the overall attainable ΔT is heavily influenced by the very poor heat exchange capabilities with the environment of small bare surfaces. Simulations and experiments show that the presence of a heat exchanger largely increase the effective ΔT, but brings into play interesting heterogeneous integration challenges still to be fully solved in terms of an effective but gentle attachment of an intermediate adapter that needs to be designed ad hoc for proper heat flow handling. The presence of the heat exchanger also affects the tilting point of the previously mentioned thermal/electrical trade-off, and thus on the final choice of materials. In the examples given, silicon-based materials have been used (silicon microbeams, silicon and silicon germanium nanowires), but similar structures could be devised for instance for any thermoelectric material in thin film form.
This manuscript contains work supported by projects FP7-NMP-2013-SMALL-7 (Contract n. 604169) SiNERGY, TEC2016-78284-C3-1-R (AEI/FEDER, EU) MINAUTO and TEC2016-78284-C3-2-R (AEI/FEDER, EU) SIGGNAL. This research has made use of the infrastructure of the Spanish ICTS Network MICRONANOFABS (CNM site) partially supported by MINECO. I. Donmez-Noyan thanks the ‘Programa de Doctorat en Ciència de Materials de la UAB’ for the support in her formative activities.