Open access peer-reviewed chapter

Cutting Superhard Materials by Jet Methods (on Functional Approach)

Written By

Alexandr Salenko, Viktor Shchetynin, Galina Gabuzian, Evgeny Lashko, Mohamed R.F. Budar, Sergey Klimenko and Alexandr Potapov

Submitted: 05 February 2019 Reviewed: 27 May 2019 Published: 21 September 2019

DOI: 10.5772/intechopen.87094

From the Edited Volume

Recent Advancements in the Metallurgical Engineering and Electrodeposition

Edited by Uday Basheer Al-Naib, Dhanasekaran Vikraman and K. Karuppasamy

Chapter metrics overview

858 Chapter Downloads

View Full Metrics


Dimensional processing of products made from hard alloys and superhard materials is of a certain interest for contemporary high-technology production, as it enables creation of half-finished or final products of various geometric shapes from workpieces obtained by sintering. In this case conventional methods, first of all abrasive processing and electroerosion cutting, find limited application, which is caused by special features of the structural condition and physical and mechanical properties of the materials of the processed workpieces. The functional approach can be used in working of composite workpieces from laminated superhard materials. The performed research with the use of hydro-abrasive cutting (HAC), laser cutting (LC), laser cutting with water cooling (LCC), and water jet-guided laser (WJGL) has enabled studying of the intensity of destruction area introduction into the worked piece and finding out the functional features of a particular process that are caused by the working conditions. It has been shown that the hypothesis of quasistationary rate of destruction is unacceptable for such materials, which is caused by the structure and high hardness of the material. It has also been determined that when deepening increases, the rate of jet introduction has a pronounced tendency toward reduction.


  • carbon materials
  • carbon composite
  • water-jet-guided laser process
  • jet methods

1. Introduction

Dimensional processing of products made from hard alloys and superhard materials, in particular, contour cutting prismatic and circular plates and arbitrary shaped flat workpieces, is of a certain interest for contemporary high-technology production, as it enables creation of half-finished or final products of various geometric shapes from workpieces obtained by sintering.

In this case conventional methods, first of all abrasive processing and electroerosion cutting, find limited application, which is caused by special features of the structural condition and physical and mechanical properties of the materials of the processed workpieces. Processing of products made from laminated compounds is especially complicated as there is a danger of breakage of adhesion bonds in the “base-surface layer” plane. Workpieces made from such products include diamond carbide (DC) composite containing an upper (working) layer of polycrystal superhard composite on the basis of synthetic diamond (PCD) and a lower (supporting) layer from hard alloy based on tungsten carbide (HA), obtained by sintering in high-pressure apparatus [1].

It was demonstrated that, first of all, liquid blasting and laser blasting have good prospects in industrial use for cutting flat workpieces from polycrystal superhard materials (PSHM) and HA, as they allow creation of the cut surface with sufficient efficiency. However, the problems of provision of high quality of the worked surfaces of the products have not yet been solved in full.

So, surfaces of products from HA and PSHM obtained by the mentioned methods are characterized by high roughness and essential deviation of the shape. In Ref. [2], it is shown that hybrid processing methods based on a combination of different ways of power and other flows impact on the material that make it possible to essentially reduce working hours necessary for production and improve the quality of processing. At the same time, analysis of the final product from the point of view of its useful functions enables improvement of the method and scientific substantiation of most rational ways of impact on the workpiece to achieve the maximum quality level.

The solution to these problems can be found in the use of an innovative approach to development of hybrid working methods; its essence consists in provision of useful functions of the product on the basis of morphological analysis of variants of combination of power and energy flows generating a hybrid production process.

The purpose of the chapter consists in development of principles of functional approach to creation of hybrid processes as a morphological combination of various ways of power and energy flows that impact on the worked piece when functions and properties of the final product are formed by totality of results of some technological transitions realized on micro-, meso-, or macro-levels of the product.


2. Approaches to problem solution and research methods

Functional approach to development and creation of new machines, objects, and complex technical systems was studied by many researchers [3]. They state that any material object is characterized by a certain totality (matrix) of functions among which it is possible to single out useful, harmful, and neutral functions (Figure 1). Unlike a material approach, a functional approach is based on the fact that the product is made to perform a number of functions provided by corresponding material carriers (the cheapest ones or the ones with the least costly manufacturing steps).

Figure 1.

Classification of the object functions: B, basic; S, secondary; D, derived (obtained without special provision); С, connected (accompany useful functions); I, independent.

This approach can also be applied to working technologies: the manufacturing process expressed through material carriers is to be minimized according to criteria taken into consideration—working time, cost price, and quality. Systemized data of this approach are presented in a number of papers, for example, [4].

The idea of modularity of technological processes (TP) and their functional orientation can develop in the following direction.

As all types of functions (useful, neutral, and harmful) are available in a final product, manufacturing steps are to be oriented in such a way that harmful functions be weakened and useful ones, in their turn, be obtained in the minimum number of steps. Under these conditions a technological process can be considered prospective if weakening or complete elimination of harmful functions takes place along with creation of useful functions during the steps.

Analysis of typical products of mechanical engineering from the point of view of functional approach reveals that practically always creation of a particular useful consumer function Fp will go together with manifestation of neutral Fn and harmful Fv functions. Then a product having only useful (under certain conditions) functions is ideal from the point of view of operation:


where Fpz are the product useful functions having the following matrix of consumer properties


Hence, an equation of restrictions (1) and optimization (2) makes it possible to choose the most rational material carriers of functions on the basis of morphological analysis and then to pass to material carriers in the technological process creating these functions.

As there is a functional interrelation between separate functions, that is,


taking into account the fact that a function is created by a separate TP step in the form of transformation element Wp, Eq. (2) can be presented in the following form:


Taking into consideration the fact that TP cannot be aimed at creation of harmful functions and properties in the product, minimization of the unnecessary functions is expressed by dependence:


or after transformation, in the following way


Approaching of the totality of the product properties to the ideal implies transformation of summands Wn¯q and Wv¯p into zero, which is possible under the condition of absence of functional relation between useful and harmful properties of the product or under the condition that the process of obtaining useful properties due to a particular TP step is at the same time the inverse one as to the occurring harmful functions. Availability and interrelation of TP separate elements enable presentation of Eq. (6) in the following way:


For totality of alternative variants of TP, the obtained equality is supplemented by quantitative signs of every function, the integral sum of which is equal to 1, then


under the condition that bniWpi¯q=0, where bki and bvi are the corresponding weight coefficients of each of the useful and harmful functions and bri is the weight coefficient of interaction of independent steps revealing reserves in improvement of output properties of the final product.

Describing the object by setting its initial condition Сn, as a totality of parameters characterizing the form and dimensions of the workpiece, its physical and mechanical properties, and final condition Ck via particular forms (dimensions, relative position of the surfaces, physical and mechanical properties, etc.), the technological transformation function φ0 is presented as


where CnR is r-th elementary property of the workpiece; CkT is t-th elementary property of the product; and R and T are total number of parameters of the workpiece and the product, respectively. The function φ0 = ΣWiEj, where Ej is the product separate elements creating its properties.

As the product separate functions expressed via obtaining parameters of geometric accuracy, condition, structure, etc. can be generated in different ways, it is expedient to create morphological tables that may provide the basis for search of more rational variants of combination of technological actions.

Let the created product realize some totality of functions F1Fl. To guarantee them the elements of condition of workpiece, Еki is to be formed in such a way (Figure 2) that

Figure 2.

Provision of the product functions Fpi by separate elements when they are generated by TP steps Wij.


Application of this approach makes it possible to reveal rational sequence of TP steps, find causes of occurrence of harmful functions and eliminate them (or invert), and also determine the possibility for hybridization of the process to meet condition (1).

As generation of assigned functions is a multivariant task (Figure 2 and Table 1), logical relations obtained on the basis of morphological analysis can be simplified according to the known rules of Boolean algebra provided that restrictions be met (7). In this case differentiation or hybridization of operation may have new effects that are to be taken into account by corresponding weight coefficients (8).

No. п/пProduct functionsElement provisionMaterial carriers—TP stepsProbable harmful functions
2Fp2E2∩E3+ E7∩E8Wp4Wp7+Wp3Wp5+Wp2Fv1

Table 1.

Components of the product useful functions and their provision by TP.

The product properties are generated as a result of a number of manufacturing steps during which a complete or partial change of the initial properties takes place. Technological transformation of a workpiece into a product is achieved by purposeful total technological impacts Wij(tk) of material So(tk), energy Еo(tk), and information Io(tк) types which enable presentation of a scheme of output properties generation according to Figure 3 and write down.

Figure 3.

Generation of the product properties during manufacturing steps by conventional (upper) and hybrid (lower) tools.


Then, on the grounds of the condition that tool technological impacts on the product are to be performed at the levels from nano-areas to the product on the whole, and the product is a 3D object, to realize the totality of variants of technological impacts the morphological matrix will correspond to the following form:


where П11s, П12s, …; П21s, П22s, …; П11t,П12t,;П21t,П22t,;П11v, П12v, …; П21v, П22v, …; …—variants of discontinuous technological actions along the corresponding axes s, t and v of the coordinate system of s, t, v;Н11s, Н12s, …; Н21s, Н22s, …;.Н11t, Н12t, …; Н21t, Н22t, …; Н11v, Н12v, …; Н21v, Н22v, …—different variants of continuous technological actions along the axes s, t and v of the coordinate system of s, t, v; Е11s, Е12s, …; Е21s, Е22s, …;—different variants of one-time technological actions.

The presence of variants of discontinuous technological actions makes it possible to consider processing of one element of the product in the form of a successive totality of different actions. In this case if the element geometric characteristics (e.g., flatness, accuracy of linear dimensions) are its output index, this process can be realized by different types of actions that more completely correspond to the properties of the workpiece elements. As actions providing the conditions for minimum error of the shape are to be taken without reinstallation of the workpiece and change of its position in the fixation and orientation device, such processes should be considered hybrid ones.

Let some element Еm of a product be obtained due to realization of discontinuous technological actions Пijt and Пij+kt. It can be expected that k tools, accordingly, will be required for the realization. However, if it is taken into account that a new tool is created on the basis of the known ones, that is, expression Rnj=i=1ρiRsi takes place, where Rnj is the field of creation of new types of tools; Rsi is the i-th totality of the known engineering solutions; and ρi is the weight of the subset of the known engineering solutions, then the newly created tool can combine the means for fundamentally different types of actions (Figure 3).

Let totalities of properties of two tools represent expressions

I1=ρ11S111ρ21S121ρk1S1k1ρ1jS11jρ2jS12jρkjS1kj, I2=ρ11S211ρ21S221ρk1S2k1ρ1jS21jρ2jS22jρkjS2kj.E10

Then a hybrid tool obtained on the basis of the principle of morphological search and combination of properties will consist of m elements and m < k + j, as some of properties of initial tools can be combined. Thus, the index of hybridization of the created instrument is kg=k+jm. This index provides the possibility to find rational engineering solutions for a hybrid tool on the grounds of a totality of the required properties of the worked product and also the possibilities to achieve them by available means.

Consider specific features of application of this approach to creation of hybrid processes for working of diamond-bearing products intended to be used as tools. Such products are rather simple, the number of elements Еі, defining functions Fj of the latter is not large and, as a rule represents several surfaces making working surfaces of the tool and a cutting element fastening plane.

Conventionally, these products represent plates of various geometric forms and are made homogeneous or laminated depending on their purpose. They are mainly worked up by an abrasive tool (AT). The use of various abrasive wheels enables obtaining flat elements of surface (during cutting or profile ones during wheel periphery copying (Figure 4a).

Figure 4.

Processing tool working surface shaped abrasive wheel (a), model of a jet device (b), a laser head for cutting the model (c).

An alternative consists in application of laser working methods, in particular, laser cutting (LC), laser cutting with water cooling (LCC) or water-jet-guided laser (WJGL), and also a method using loose abrasive accelerated by a supersonic liquid flow—hydro-abrasive cutting (HAC). In this case the obtained surfaces can be of an arbitrary form determined by operational movement of the tool in relation to the worked surface (Figure 4c).

Peculiar features of application of these processes are discussed in [1, 3, 5].

As preliminary research has revealed, separate application of these methods is not optimal.

Let us consider specific features of LC, LCC, WJGL, and HAC from the point of view of a functional approach.

HAC is known to generate a stressed condition at the obstacle—the worked surface; this state is described by components


where U(t) and H(t) are components of movements at a particular point of the surface that are determined as Ut=12νpotDk224G;0<Di2<Dk2;Ht=12νpotDk2G; G and μ are the shift module and Poisson ratio of the worked material, respectively; ε is the volume deformation; Δ=d2dr2+drr+d2z2 is the Laplace operator; and р0 is the pressure at the obstacle pi=0,5ρvi2+ρvi2dQ.

Intensification of the stressed condition contributes to development of initial defects and creation of a grid of microcracks actively joining under the action of abrasive particles when material particles come off the surface. HAC is characterized by the property to efficiently continue working only till the moment when the loss of jet energy due to friction against the surface of the funnel that appeared is comparable with the energy at which the cutting process ceases.

In particular, in [1, 5] it is shown that during working of carbides (HA), the dimple depth hl increases due to manifestation of mechanisms of micro-cutting and deformation destruction, that is, the process is described by the expression hl=cmav28σu2+2ma1cv2πuεDj, where с is the process constant; ma is the abrasive mass flow; v is the velocity of abrasive particles movement, v=2pbfbfb2pb/ρ+ma; σ is the material flow stress; u is the feed rate; ε is the material specific energy; and Dj is the flow diameter corresponding to the diameter of the nozzle section.

On the other hand, due to flow energy losses, the real depth of the obtained dimple will be less and can be taken into account by the relation


where N1=vcv;N2=π2εdj2mav;N3=uv;vc is the critical velocity of abrasive particles movement.

A peculiar feature of cutting hard composite workpieces used in tools both separately and in the form of bases for the required layers of other materials consists in the fact that particles flowing on the surface cause local highly intensive loads resulting in some elastoplastic compressive macrodeformations in local volumes of the surface layer. These loads are mainly received by the carbide structure (for alloys containing cobalt ≤10%). Further pickup of the abrasive particle by liquid flow results in removal of compression load and partial elastic restoration of the deformed volume of the surface layer, that is, in occurrence of tensions in this local volume, which causes redistribution of tensions among the components of HA structure. In this case, at first carbide grain boundaries break, which results in appearance of microcracks in HA carbide grains themselves and plastic deformation along the dislocation mechanism of cobalt bundle [2, 3]. After that the boundaries between the carbide grains and the bundle and the bundle itself break.

Hence, movement of the destruction area slows down when the cutting depth increases, and distortion of the jet as a “nonrigid” tool increases.

Much higher rigidity of polycrystal superhard materials, including cubic boron nitride (PSHM, CBN) and diamond-bearing elements (DBE), causes the fact that a moving flow of abrasive grains slightly influences the worked material and the workpiece is not cut at a speed admissible by manufacturing conditions (Figure 5a).

Figure 5.

Surface defects as manifestation of harmful functions of technological actions: (а) incomplete cutting; (b) surface waviness; (c) surface cleavages.

Obtaining the initial groove and creation of a cut or a channel result in distortion of the jet and its drift from the theoretic axis to the side opposite to the feed movement. It is facilitated by selectivity of destruction caused by “nonrigidity” of the jet, due to which creation of specific destruction areas takes place (Figure 5b); their location and dimension determine the form of hydro-cutting front and deviation of the jet by angle α, whose value is determined by the relation of speed vz of jet penetration into the worked material and feed rate s. This phenomenon results in appearance of surface defects in the form of waviness and also in cut edge deviation from orthogonality.

The jet ability to selectively go about obstacles results in the fact that heterogeneity of the worked material and specific features of the power scheme may provoke availability of both bumpy elements of the surface and surface cleavages (Figure 5c).

Thus, the possibilities of HAC process from the point of view of the functional approach can be presented by elements of Table 2. In this case the ability of the jet to destroy the obstacle with creation of vertical edges can be regarded as a useful function only for a restricted number of materials.

Worked materialFunctions F
Useful FpiHarmful FvkNeutral Fnj
Obtaining of orthogonal edge of the product h, mmWaviness δ, μmSurface cleavageWorkpiece heat, Т (°С)
HAFp1 depends on cutting modesFvk depends on cutting modesMinimumUp to 50–60
PSHMWeakHighCompleteUp to 50–60
PCDAbsentAbsentInsignificantUp to 50–75

Table 2.

Provision of the product function by creation of element Еі by a technological action Wij(tk) at HAC.



under the condition that Fv2 and Fn1 can be neglected and useful and harmful properties (functions) are manifested simultaneously. Corresponding transformations in the form of the process result, for example, depth h (the surface element linear value) for HA, may represent regression equations in the form


where Ma is the abrasive grains mass flow, hm is the thickness of the worked material, and for other materials hWFp=0 and δWFv=0.

It is obvious from the given relations that these two dependences are interconnected and increase of cutting depth h at a higher rate of contour feed sk results in increase of waviness δ.

More possibilities are provided by combined working of material by wate-jet-guided laser (WJGL). In this case working variants correspond to schemes in Figure 6; in this case both WJGL (Figure 6a) and LCC (Figure 6be) can be realized.

Figure 6.

Variants of combination of a water jet and a laser beam for performance of WJGL (a) or LCC (b–e).

The action of a water jet or a laser beam can be both simultaneous and successive. In this case different variants of laser blasting and possibilities of variation of the form of jet nozzle flow section, as shown in [6], provide good prospects in combination of methods of actions on the worked piece and, consequently, in meeting principle (10).

Application of thermo-hydrodynamic jets typical of WJGL or LCC causes heating of the workpiece whose temperature field can be described by equation [7]


where t is the time from the moment of beginning of thermal impulse action, ρ, с, λ, α=λср, and h* are density, specific heat capacity, heat conductivity coefficient, temperature conductivity of the workpiece material, and coefficient of heat transfer from the surface of the workpiece, respectively;α=λсрА and В are the bigger and smaller half axes of beam elliptic section; and P = πqAB is the power of the lasing emitter. Integral equation of heat energy balance in an arbitrary area ω ⊂ Ω according to [4] will take the form wetdv=wgdvwqT+cgρgTvfnds.

Taking into account the boundary conditions in the cutting zone


temperature distribution across the sample section is obtained; its analysis reveals the following (Figure 7): temperature distribution across the surface is determined by conditions of coolant outflow and may considerably vary with the change of the flow shape; when the thickness of the sample increases, considerable reduction of the jet’s ability to perform the work of destruction can be observed, as at the same amount of rejected heat, the amount of delivered heat constantly decreases.

Figure 7.

Changes in border radius zone temperature field (T = 850°C) as a function of time for different processing methods LC (×, Ж, ), LCC (), WJGL (, ) (а) and cutting depth in materials (HA, ; PSTM, ) depending on the number of cuts (b).

Thus, it is possible to create a table of provision of the product with the function via formation of its separate element or a totality of elements. This table is analogous to the one considered above (e.g., for WJGL; Table 3), but it reflects the peculiar feature of each of the variants in Figure 6. It should be noted that the given tables just illustrate the approach and draw attention to the most important functions, while a totality of such functions may be much bigger.

Worked materialFunctions F
Useful FpiHarmful FvkNeutral Fnj
Obtaining of orthogonal edge of the product (depth h, mm)Thermodestruction δ, μmCracking l, mmVariation of porosity P
HAIntensive, linearly depending on t (number of cuts N)MinimumExistsAbsent
PSHMIntensive, decreasing with increase of groove depth hlMinimumMinimumIs observed in destructed zone
PCDNonlinear medium-intensiveEssentialAbsentIs observed in destructed zone

Table 3.

Provision of the product function by creation of element Еі by a technological action Wij(tk)—WJGL.

On the basis of Table 3, technological action for obtaining a particular element can be presented as


Corresponding transformations for LB for different materials include four equations now (according to the number of components):


where Т is the impulse energy, Qv is the liquid discharge out of the nozzle, and hl is the depth of the groove in the worked piece.

Analogous tables, including the ones with extended features of functions F′, are created for all the types of working.

The obtained dependences (12) and (14) make it possible to determine the totality of variants for carrying out the process of working of a particular element of the surface, and the most optimal method can be searched on the basis of morphological analysis.

This approach is applicable not only to the processing of superhard materials. It can also be successfully used for the treatment of special difficult-to-cut materials, such as carbon-carbon composites, multilayer aircraft panels, etc. [9, 10, 11].


3. Used equipment, workpieces, and succession of experimental research

Cut workpieces of HA T5K10, PSHM on the basis of CBN “borsinit” represented plates of the size 12.7 × 12.7 mm, of the thickness up to 3.5 mm, DC workpieces were two-layer composites of the size 12.7 × 12.7 mm with an upper PCD-layer of the thickness up to 1.0 mm and a hard alloy base of the thickness up to 3.0 mm.

The cuts were performed by methods of hydro-abrasive (HAC), laser (LC) cutting, laser cutting with liquid cooling (LCC), and water-jet-guided laser (WJGL).

Experiments were carried out with the use of laser blasting complex LSK-400-5, equipped with a hydro-abrasive head with water nozzle dc = 0.22 mm and a metering tube Dk = 1.05 mm.

HAC was performed with abrasive consumption up to 0.5 kg/min and under liquid pressure of 250 МPа. Garnet sand of granularity of 300 meshes was used as abrasive during cutting.

During multi-cut laser blasting, the cuts were performed with feed up to 50 mm/min. Impulse Nd:YAG laser with impulse frequency of 75–150 HZ and power of 400 W was used. For realization of the hybrid process, the unit was equipped with a special laser blasting head enabling working with the use of a ring laser nozzle and a mixing chamber to provide hydro-abrasive cutting without disturbance of the position of basic axes of the tools. The beam was focused according to a method providing centering and ingress of all its modes on the focusing lenses of the tube. Optic elements were blown with purified compressed air through a nozzle of ∅ 2.8 mm under excess pressure of 0.05 MPa. During LB the liquid was fed directly into the center of laser focus under the pressure of 25–50 MPa.

A high-temperature carbon-carbon composite weave composite was also used.


4. Discussion of the obtained results

Paper [5] contains comparative results of the research of productivity of different working methods. In the present paper, experiments with workpieces made of HA and PSHM are repeated, but attention is focused on the indices of the quality of the worked surfaces, roughness and accuracy of relative position, and also deviations of their values from theoretically possible ones.

To determine components in Tables 2 and 3, the values of separate parameters whose averaged values are given in Table 4 are determined. Comparison of erosion rates determining the rates of deepening of the cutting dimples is given in Table 5. In this case only particular results of the research are shown; they are sufficient for hybridization of the process according to principle (10).

Type of workingHACLCLCCWJGL
Modes of working100 mm/min, 350 MPa, 0.5 kg/min30 mm/min, 400 W, 100 Hz30 mm/min, 400 W, 100 Hz, 0.5 MPa
2.80 mm1.05 mm
HARa, μm12.
h, mm/cycle6.
δ, mm/5.0 mm0.3–0.90.02–0.150.02–0.090.02–0.04
PSHMRa, μm6.3––3.2
h, mm/cycle<0.013.0––1.75
δ, mm/5.0 mm0.800.05–0.100.02–0.05

Table 4.

Accuracy and roughness of the surfaces of workpieces made from HA and PSHM at different jet working methods.

Table 5.

Material erosion rate at HAC, LC, LCC, and LB depending on the thickness of the plate.

The performed research revealed the following. Any initial deviation of the cut shape, especially during performance of discontinuous working processes, distorts the jet, and further working results only in deterioration of the quality of the product, first of all, due to progressive deviation of the cut shape. It concerns all the types of working. So, Figure 8 demonstrates a defect of DC cutting in the form of deviation from orthogonality of the edge at partially incomplete cutting of PCD layer.

Figure 8.

PCD layer after WJGL (а) and a plane of adhesion of PCD with WC (b).

A peculiar feature of two-layer DC consists in the fact that workability by a certain method changes on the surface obtained at the section, depending on the structure of the material and physical and mechanical properties. A peculiarity of DC consists in the fact that PCD is not practically worked by HAC, while it can be worked by LCC and WJGL. The carbide base is worked by HAC with high efficiency.

Hence, generation of the surface as an element of the product can be presented in the form of logical multiplication of transformations W1i(tk) and W2i(tk) and is described by the expression


Thus, taking into account the condition of provision of initial high-quality formation of a destruction dimple in PCD layer, a hybrid process is to represent a totality of processes of initial WJGL up to the moment of complete cutting of PCD layer and creation of a dimple in WC with further cutting of the plate by HAC (Figure 9).

Figure 9.

Making a cut in PCD and PSHM workpieces.

Further research is to be directed to determine rational combinations of hybridization at multi-cut working, at which the number of cuts directly influences the quality of obtained surfaces, and also to the condition of adhesion surfaces in multilayer products.

Comparison of the diagrams of cutting rates of DC and PSHM demonstrates (Figure 10) that productivity of the process is determined by obtaining scribe in the superhard layer. HAC cutting of hard alloy base is practically performed in an identical way.

Figure 10.

Change in the width of the destruction zone depending on the time of the interaction of the cutting surface with the tool.

Let the acquisition of an array of properties of a finished product (a sample of a carbon-carbon composite) in the form of sets Fi (l, b, h, r, δ …) be possible by the implementation of a certain set of technological influences Mj, inherent in one or another method of processing. Each technological effect can be represented as a set of sets of properties of the tool Tj, the dynamic properties of the processing system Wj, the method of power influence Pj, for which (Tj, Wj, Pj) ∈ Mj, which gives the opportunity to perform with the properties of Si, output quality parameters to be presented as:


Based on the provisions reflected in the work [8], we can record the condition for providing output processing parameters as


which gives a set of variants of processing conversions, the best of which can be selected according to a certain criterion.

Since this material is resistant to temperature effects, the only way to treat it is mechanical abrasive cutting.

Take into account the following processing methods: R1, milling; R2, processing with abrasive disc; R3, processing by the renovator (reciprocating motion); R4, drilling; and R5, hydro-abrasive cutting. For these methods, the maximum stresses and diagrams of stress distribution at the intersection of the cut in the workpieces are determined.

The cutting modes, as well as the parameters of the applied tool, directly determine not only the processing performance but also the thickness of the destruction of the surface layer, which must be taken into account when processing samples for mechanical tests.

On the other hand, in the process of processing, there is wear of the tool: the change of angles on the cutting edge and curing abrasive grains. All this leads to the fact that even in stable cutting modes, the parameters of the surface layer are changed.

The change in the width of the destruction zone (Figure 10) measured on the natural samples (shown as separate points in the diagram) shows the following. The “hardness” of the hydro-abrasive jet leads to the fact that the power circuit of the interaction is constantly changing and, consequently, the components are increasing, that is, the flow will then simply blur the machined sample, which requires minimization of the time of finding the jet in a stationary state.

When processing materials with diamond disks or saw blades, there is no significant change in the width of the destructive zone.

We also propose rather simple regressive dependences of the width of the destruction on the function of maximum stresses in the cutting area δ = f(σmax):


where δ1 is the destruction of carbon-carbon material and δ1 is the destruction of the carbon polymer, which made it possible to construct and compare diagrams of the development of the width of the destructive zone (Figure 11) of the processing of carbon composites, which are formed by various methods.

Figure 11.

Emerging stresses under different processing methods and their effect on the width of the destruction zone.

Thus, we have shown that obtaining qualitative samples of a complex configuration is associated with some complexities due to the heterogeneous structure of the treated material, as well as the manifestation of quasi-cleaved properties of carbon reinforcing fibers.

In this case, the main condition for obtaining the desired result is the restriction of the thickness of the destructive layer at >2% of the measurement basis.

The application of the proposed approach allows for the task of obtaining a sample a × b × h from a cubic blank in A × B × L sizes, to offer the following possible technological operations: R2-R1; R2-R5; and R2-R4-R5. When optimizing the process by the criterion of minimizing the processing time for a given level of quality, a variant of the functionally oriented process (R2)-(R4)-(R5) is obtained, the scheme of which is shown in Figure 12.

Figure 12.

Sequence of sample preparation from carbon fiber blanket as the result of cutting.

Such a sequence of operations allows us to make full use of all the benefits of hydro-abrasive cutting (a significant reduction in the processing time) and to avoid material destruction at the time of the breakdown by the jet.


5. Conclusions

Application of the functional approach makes it possible to reveal rational succession of TP steps, find optimal conditions and points of occurrence of harmful functions, eliminate them (or invert), and also determine the possibility of hybridization of the process. Such an approach can be used in working of composite workpieces from laminated superhard materials.

The performed research with the use of HAC, LC, LCC, and WJGL has enabled studying of the intensity of destruction area introduction into the worked piece and finding out the functional features of a particular process that are caused by the working conditions. It has been shown that the hypothesis of quasistationary rate of destruction is unacceptable for such materials, which is caused by the structure and high hardness of the material. It has also been determined that when deepening increases, the rate of jet introduction has a pronounced tendency toward reduction.

A peculiar feature of cutting two-layer composites including a PCD layer based on HA has been analyzed, and it has been shown that the use of functional approach principles makes it possible to propose a hybrid process and corresponding hybrid tool (combining WJGL and HAC), enabling efficient and productive cutting of such plates. Besides, conditions for essential improvement of working process efficiency have been demonstrated (Figures 13 and 14).

Figure 13.

Intensity of scribe development (а) in workpieces from PCD () and PSHM () (linear feed rate, 35 mm/min; impulse passing frequency, 75 Hz) and a cut product (b).

Figure 14.

The result of cutting carbon-carbon composites.

To improve the considered approach, it is necessary to orientate further research to optimization of working conditions and search for ways of improvement of cut quality by selection of rational parameters of the process and design solutions for the hybrid tool.


  1. 1. Novikov NV. Superhard Materials. Obtaining and Application. Vol. 1. Dumka: Nauka; 2003. 320p
  2. 2. Klimenko SA, Mel’niichuk Yu A, Vstovskii GV. Interrelation between the structure parameters, mechanical properties of sprayed materials and the tool life in cutting them. Journal of Superhard Materials. 2008;30(2):115-121
  3. 3. Fedotyev А, Fedotyeva L. The Prospects of Carbolloies Waste Utilization as Wearproof Coverings. Vol. 39. Gabrovo: Izvestiia na Tekhnicheskiia Universitet Gabrovo; 2010. pp. 30-33
  4. 4. Gindin PD. A mathematical model of thermal cleaving of brittle anisotropic materials. Surface. 2010;1:14-18
  5. 5. Salenko AF, Shchetinin VT, Fedotyev AN, et al. Methods of cutting for workpieces of hardmetal and cBN-based polycrystalline superhard material. Journal of Superhard Materials. 2015;37(4):271-281
  6. 6. Salenko O, Gabuzyan G, Myronov Y, Nikitin V. About some results of processing SiC-microarrays by hydroabrasive precision jet. Journal of Mechanical Engineering NTUU “Kyiv Polytechnic Institute”. 2013;67:178-184
  7. 7. Schulz W, Niessen M, Eppelt U, Kowalick K. Simulation of laser cutting. In: Dowden J, editor. The Theory of Laser Materials Processing. Vol. 119. Springer; 2009. pp. 21-69
  8. 8. Salenko AF, Shchetinin VT, Fedotyev AN. Improving accuracy of profile hydro-abrasive cutting of plates of hardmetals and superhard materials. Journal of Superhard Materials. 2014;36(3):199-207
  9. 9. Kholodnyi V, Salenko O. The water jet guided laser method in punching honeycomb cores for aerospace sandwich panels. Eastern-European Journal of Enterprise Technologies. 2016;1(5(79)):19-30. DOI: 10.15587/1729-4061.2016.59870
  10. 10. Ivanova VS, Balankin АS, Bunin IZ, Oksogoiev АА. Synergy and Fractals in Material Science. Moskva: Nauka; 1994. 384p
  11. 11. French MJ. Design principles applied to structural functions of machine components. Journal of Engineering Design. 1992;3(3):229-241

Written By

Alexandr Salenko, Viktor Shchetynin, Galina Gabuzian, Evgeny Lashko, Mohamed R.F. Budar, Sergey Klimenko and Alexandr Potapov

Submitted: 05 February 2019 Reviewed: 27 May 2019 Published: 21 September 2019