Open access peer-reviewed chapter

Surface Magneto Plasmons and Their Applications

By Bin Hu

Submitted: March 12th 2018Reviewed: June 27th 2018Published: November 5th 2018

DOI: 10.5772/intechopen.79788

Downloaded: 869


Due to their promising properties, surface magneto plasmons have attracted great interests in the field of plasmonics. Apart from flexible modulation of the plasmonic properties by an external magnetic field, surface magneto plasmons also promise nonreciprocal effect and multi-bands of propagation, which can be applied into the design of integrated plasmonic devices for biosensing and telecommunication applications. In the visible frequencies, hybrid nanodevices consisting of metals and magnetic materials based on surface magneto plasmon are proposed. In the infrared frequencies, highly-doped semiconductors can replace metals, owning to the lower incident wave frequencies and lower plasma frequencies. Furthermore, a promising 2D material-graphene shows great potential in infrared magnetic plasmonics. In this book chapter, we will review the magneto plasmonics with a focus on device designs and applications. We will give the basic theory of surface magneto plasmons propagating in different structures, including plane surface structures and slot waveguides. Based on the fundamental investigation and theoretical studies, we will illustrate various magneto plasmonic micro/nanodevices, such as tunable waveguides, filters, and beam-splitters. Novel plasmonic devices such as one-way waveguides and broad-band waveguides will also be introduced.


  • surface magneto plasmons
  • plasmonics
  • magnetic field tuning

1. Introduction

Surface plasmons (SPs) are electromagnetic waves that are confined on and propagate along and the surface of a conductor, usually a metal or a semiconductor [1]. SPs are caused by the resonant oscillation of the free electrons in the conductor with the incident electromagnetic waves. The resonant oscillation can be denoted by a characteristic frequency—the plasma frequency ωp, which decides the scale of the free electrons response to time-varying perturbations [2]. Since SPs depend on the free electron motions, it can be imagined that an external magnetic field may have modulations on the SPs, due to the Lorentz force which can change the response of carriers. In this situation, another characteristic frequency called cyclotron frequency ωcis often used, which is a function of the effective mass of the charge carriers and the strength of the applied magnetic field [3]. One of the important consequences of magnetizing the plasmons is that the polarizability becomes highly anisotropic (the permittivity of the conductor becomes a tensor)—even though the medium is isotropic when the magnetic field is not applied. Therefore, SPs may have different properties when they are propagating under an external magnetic field. In this situation, they are usually called surface magneto plasmons (SMPs) [4].

SMPs can be divided in three principal configurations, according to three directions—the orientation of applied magnetic field B, the propagation of the surface wave k, and the surface. The first one is called perpendicular geometry, in which Bis perpendicular to both the surface and k. The second one is called Faraday geometry, in which Bis parallel to the surface and k. The third one is called Voigt geometry, in which Bis parallel to the surface and perpendicular to k. Compared with traditional SPs, SMPs have several unique properties. For instance, SMPs in perpendicular geometry and Faraday geometry can support pseudo-surface waves, which means they attenuate on only one side of the surface [5, 6]. SMPs in this Voigt configuration support nonreciprocal effect, which means the SMP dispersions are different when they propagate along two opposite directions. In addition, unlike SPs only has one propagating frequency band which is below the plasma frequency [2], SMPs support two propagating bands.

The basic theory of SMPs in the perpendicular configuration was first given by Brion et al. [5] in 1974. Then, in the same year, Wallis et al. reported the theoretical study of SMPs in the Faraday configuration [6]. In 1987, Kushwaha [7] gave the theoretical derivation of SMP on a thin film in the Faraday configurations. For the Voigt configuration, the pioneer work was implemented by Chiu et al. [8] and Brion et al. [4] as early as 1972, separately. Then De Wames and coworkers studied the dispersion relation of Voigt-configured SMPs on a thin film [9]. Then SMP properties considering holes [10], optical phonons [11, 12, 13], diffuse electron density profiles [14], and metal screen [15] were theoretically proposed. They were also studied both theoretically and experimentally in various structures [16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27]. In 2001, a review work of SMP was given [28].

In recent years, due to the extraordinary optical transmission through periodic holds in nanometer scale, which is found in 1998 [29], numerous plasmonic devices, made of metals, have been theoretically proposed and experimentally realized in the visible frequencies [1, 30]. Compared with studies about SPs before 2000 [31, 32, 33, 34, 35, 36, 37, 38, 39, 40], these structures have been mostly focused on the subwavelength confinement of electromagnetic waves [41]. For example, in the slot waveguides [42] or metal-insulator-metal structures [43], electromagnetic waves can be confined in a space as small as ∼0.1λ. Inspired by these structures, some SMP devices composed of metals were proposed [44, 45, 46, 47, 48, 49]. However, all of these SMP structures are difficult to realize because they require unreachable magnetic fields. The reason is that in order to observe the effect of an external magnetic field, it requires ωp, ωcand the incident angular frequency ωbe comparable. However, for a metal in the visible frequencies, ωpand ωare usually in the order of ∼1016 and ∼1015 Hz, respectively. Therefore, it needs a magnetic field as strong as ∼103 Tesla, which is difficult to realize in laboratories. So far, there are two ways to solve this problem. One is using ferromagnetic materials, such as Ni and Co in nanostructures [50, 51, 52, 53, 54, 55, 56, 57]. By this method, the intensity of the applied magnetic field can be decreased to a scale of ∼mT. But it introduces large loss. The other solution is using semiconductors instead of metals in THz regime to decrease both ωpand ω. ωpof a doped semiconductor can be decreased in an order of ∼1013 Hz. Therefore, the required external magnetic field can be less than 2 Tesla. Some researches of SMP devices consisting of semiconductors have also been proposed recently [58, 59, 60, 61, 62].

In this chapter, we will introduce the basic theory of SMPs in the Voigt configuration and their applications in SMP devices design. In Section 2, we will give the dispersions of SMPs on a surface, in a metal-insulator-semiconductor structure, and in a semiconductor-insulator-semiconductor structure of the Voigt configuration. The nonreciprocal effect and the two propagating bands will be discussed. In Section 3, some intriguing plasmonic devices based on the SMPs will be presented, including one-way waveguides, broadly tunable THz slow light waveguides, and focal-length-tunable plasmonic lenses.


2. Theory of SMPs on a surface and in a slot waveguide

The first theory of SMPs on a conductor plane surface in the Voigt configuration was presented by Chiu et al. [8]. However, they only found the nonreciprocal effect. In the same year, Brion et al. gave a more comprehensive study on SMPs, including the nonreciprocal effect and the two propagating bands [4]. They also gave an explanation of why the higher band appears. We will give a review of his research in this section. Although the energy of SMPs is confine on the plane surface, the confinement is not subwavelength scale (in the order of ∼2–3λ). In order to solve this problem, in this section, we derive the dispersion of SMPs in a slot waveguide, which can confine light in 1/10 λ in the lateral direction [63, 64, 65, 66]. Some results are very similar with that in Ref. [4], while some are quite different. For example, the nonreciprocal effect is eliminated in a symmetric structure [63].

2.1. Dispersion of SMPs on a plane surface

Figure 1.

Schematic structure of SMPs propagating on a metal/semiconductor surface in the Voigt configuration. The external static magnetic field B is applied along the y-axis.

The schematic structure is shown in Figure 1. The material of x < 0 is a metal or a semiconductor, and its surface is oriented to +x-axis. The SMPs is propagating along the z-axis. In the Voigt configuration, the applied magnetic field Bis applied along the y-axis. Then the permittivity of the metal/semiconductor becomes a tensor:


The parameters in Eq. (1) have the expressions of


in which ωpis the plasma frequency of the conductor, ωis the angular frequency of the incident wave, εis the high-frequency permittivity, and ωc = eB/m* is the cyclotron frequency. eand m* are the charge and the effective mass of electrons, respectively. Bis the applied external magnetic field. υ = e/(μm*) is the collision frequency of free electrons, μis the carrier mobility.

From the Maxwell equations, the wave equation can be derived as


where k0 is the wave vector in vacuum. εis the permittivity of the material (for a conductor, it is the dielectric constant tensor of Eq. (1)). cis the light velocity in vacuum. If we assume that the material of the region x > 0 is a dielectric with permittivity of εd, and considering SMPs are TM polarized (with the magnetic field component parallel to the y-axis), the electromagnetic fields in the metal/semiconductor and the dielectric have the form:


where βis the wave vector of SMPs. From Eqs. (6), (7) and (1), we have a nontrivial solution of Eq. (5) only if


where εV = εxx + εxz2/εxxis the Voigt dielectric constant. With the consideration of the characteristics of the surface mode and the continuity of Hyand Ezat the surface, the dispersion relation of the waveguide is given by


It can be clearly seen from Eq. (10) that this dispersion is non-reciprocal with respect to the direction of propagation, i.e., the positive and negative values of the wave vector βare not equivalent. The dispersion equation can be solved numerically by Eq. (10). In Figure 2, the dispersion of SMPs on a plane surface is plotted, assuming that the conductor material is InSb in the lossless case (υ = 0) with ωc = 0.5ωp, and the dielectric material is air (εd = 1). The other corresponding parameters of InSb are chosen as m* = 0.014 m0 (m0 is the free electron mass in vacuum), ωp = 12.6THz, and ε = 15.68 [4].

Figure 2.

Dispersion curves of SMPs at the interface of InSb and air in the Voigt configuration (solid lines).ωc = 0.5ωp.ξ = ω/ωpandζ = βc/ωpare normalized frequency and wave vector.

As shown in the dispersion equation, the nonreciprocal effect is immediately observed. We first discuss the case of β > 0. An interesting feature is that the dispersion curve consists of two propagation bands with a gap between them. The lower curve starts from the origin, rises just to the right of the light line (the line marked as α0 = 0), bends over, and terminates when it reaches the dispersion curve of the bulk magneto plasmons (the line marked as α = 0). The higher branch starts from the line of εxx = 0, and approaches the asymptotic frequency for the non-retarded magneto plasmons defined by εd + εxx-xz = 0. The reduced wave vector at which the upper band starts is specified by the equation of


where Ωc = ωc/ωp. In order to let ζsto be positive and finite, it must be satisfied that ε/εd > ωH/ωc, where ωH = sqrt(ωp2 + ωc2) is the hybrid cyclotron-plasmon frequency. For InSb and air, this is given by Ωc ≥ 0.064. Therefore, the magnetic field should be at least 0.0643 Tesla to observe the higher band.

For β < 0, the lower band starting from the origin to the asymptotic value defined by εd + εxx + xz = 0. The higher band starts at the light line εxx = 1, rises to the right of the light line, and cutoff when it meets the higher bulk magneto plasmon curve α = 0.

Figure 3.

Voigt dielectric constantεVas a function of frequency.

The two propagating band can be explained by Figure 3, where the Voigt dielectric constant is plotted as a function of the normalized angular frequency ξ = ω/ωp. It can be seen that when ωc = 0.5ωp, there are two regions, where εV < 0. Because SMPs can only propagate on the surface of a material with negative permittivity, SMPs have two propagating bands on a plane surface.

2.2. Dispersion of SMPs in a symmetric slot waveguide

Figure 4.

Schematic of SMPs propagating in a symmetric conductor-insulator-conductor structure in the Voigt configuration. The external static magnetic field B is applied along the y-axis.

In order to expand the theory of SMPs in a subwavelength scale, we study the dispersion of SMPs in a slot waveguide with a lateral width in subwavelength scale. In this part, we study a symmetric structure, which is shown in Figure 4. An insulator layer (the permittivity is denoted by εd) with a width of wis sandwiched by two conductor layers. A TM-polarized electromagnetic wave (the magnetic field component is parallel to the y-axis) is propagating along the z-direction where Ex(r, ω), Ez(r, ω), Hy(r, ω) ∝ exp[i(βz-ωt)]. An external static magnetic field Bis applied uniformly along the y-axis, in a Voigt configuration. Therefore, according to the Maxwell equations, the electromagnetic field components in region I, II, and III can be written as


where A, B, C, and D are undetermined coefficients. κ1, κ2 and κ3 are expressed by


Employing the boundary conditions at the two interfaces (x = −w/2 and x = w/2) yields


The nontrivial solution of these linear equations requires the vanishing of the coefficients determinant, and then we can derive the following relation:


Eq. (21) is the dispersion relation of TM-polarized SMPs in the Voigt configurations for the symmetric slot structure. It should be noted that, when B = 0, Eq. (21) becomes the dispersion relations of SPs in a MIM structure [43]; when w → ∞, it becomes Eq. (10).

Figure 5.

Dispersion curves of SMPs in a slot waveguide of InSb-air-InSb in the Voigt configuration (solid lines).w = 0.1 × 2πc/ωp.ζ = βc/ωpis the normalized wave vector.

An intriguing feature of Eq. (21) is that due to the symmetric structure, the nonreciprocal effect of Eq. (10) is eliminated because only β2 can be found in the equation. The dispersion curve is shown in Figure 5. Without loss of generality, here we also assume the conductor material is n-doped InSb. The width of the dielectric is w = 0.1 × 2πc/ωp. It is found that β > 0 and β < 0 SMP waves have same dispersion curve when the magnetic field is applied (blue lines). In addition, the two propagating bands are remained. The higher band can also be explained by the effect of the applied magnetic field on the Voigt dielectric constant εVin Figure 3.

Figure 6.

NormalizedExintensities of SMPs mode along the x-axis under an external magnetic field ofωc = 0.5ωp. (a) Lower band; (b) higher band.

Although the dispersion curve is reciprocal, the mode distribution is still nonreciprocal in this structure, which is shown in Figure 6. The normalized electric field intensities of the SMPs modes indicate that with the magnetic field, the mode distribution becomes asymmetric. For the SMPs mode in the lower band, most of the energy is confined on the lower surface of the dielectric layer, while the energy is mostly confined on the upper surface in the higher frequency band.

2.3. Dispersion of SMPs in an asymmetric slot waveguide

Figure 7.

Schematic of SMPs propagating in an asymmetric conductor-insulator-conductor structure in the Voigt configuration. The external static magnetic field B is only applied on the conductor below the insulator.

In this part, we study the dispersion of SMPs in an asymmetric slot waveguide with a lateral width in subwavelength scale, which is shown in Figure 7. The structure is similar with Figure 4, an insulator layer is sandwiched by two conductor layers. However, the external magnetic field is only applied on one of the two conductor layers. In this geometry, the conductor of region III is anisotropic, and its permittivity is a tensor, as we discussed earlier, but the conductor of region II is isotropic. Therefore, according to the Maxwell equations, the electromagnetic field components in region I, II, and III can be written as


where A, B, C, and D are undetermined coefficients. εmis the isotropic permittivity of region II. κ1, κ2 and κ3 are expressed by


Employing the boundary conditions at the two interfaces (x = −w/2 and x = w/2), it can be derived


Then we can derive the dispersion equation of SMPs in an asymmetric slot waveguide by the nontrivial solution of these linear equations:


Figure 8.

Dispersion curves of SMPs in an asymmetric slot waveguide in the Voigt configuration (solid lines).w = 0.1 × 2πc/ωp.ξ = ω/ωpandζ = βc/ωpare normalized frequency and wave vector, respectively.

One can know by a glance from Eq. (32) that in an asymmetric slot waveguide, SMPs have nonreciprocal dispersion as those on a plane surface. In Figure 8, the dispersion curves of both β > 0 and β < 0 are plotted, when w = 0.1 × 2πc/ωp, ωc = 0.1ωp. It can be seen that due to nonreciprocal effect, forward propagating and backward propagating SMPs have different cutoff frequencies.


3. Applications of slot SMPs

In recent years, several kinds of SMP devices that can manipulate electromagnetic fields in subwavelength scale have been proposed [46, 47, 48, 49, 52, 53, 54, 55, 56]. However, most of them are focused on the magnetic-field tunable property. The nonreciprocal effect and the two propagating bands are rarely utilized. In this section, we give three applications using the nonreciprocal effect, two propagating bands and magnetic field tuning properties, respectively. The SMPs applications are realized by semiconductors in the terahertz regime. However, the design principle can be used in any SMP devices.

3.1. Broadly tunable one-way terahertz plasmonic waveguides based on nonreciprocal effect of slot SMPs

With the rapid development in Terahertz (THz) technology in recent years, THz plasmonic components, e.g. waveguides, have been proposed due to the sub-wavelength confinement for miniaturized devices. However, most plasmonic waveguides are two-way waveguides, i.e. light waves propagate in both the forward and the backward directions. One-way-propagating waveguides are highly desired in splitters, switches and isolators. One method to realize one-way plasmonic devices are based on interference of SPs [66]. This effect is strongly sensitive to geometric structure variations. Another approach is by the nonreciprocal effect of SMPs under an external magnetic field. The dispersions of the forward and backward propagating SMPs terminate at different cut-off frequencies, making it possible to realize an absolute one-way plasmonic waveguide.

In this section, we propose a simple THz one-way sub-wavelength plasmonic waveguide that needs only 1 Tesla. By tuning the applied MF, the central frequency of the one-way-propagating frequency band is shifted from 1.5 to 0.36 THz when the MF is increased from 0.5 to 5 Tesla.

Figure 9.

(a) Schematic structure of the one-way THz plasmonic waveguide. It is composed of metal (upper), dielectric (middle), and semiconductor (lower) layers. (b) Dispersion relations of the THz SMPs without and with an external magnetic field.

The schematic structure of the proposed waveguide is depicted in Figure 9(a). It is composed of a metal-dielectric-semiconductor. The metal and the semiconductor layers are half-infinite and the thickness of the dielectric layer is w. The external static magnetic field is applied uniformly on the whole structure along the y-axis (as indicated by B), forming a Voigt configuration. Without loss of generality, we assume the metal, dielectric and semiconductor are Au, air and InSb, respectively. Although Au is a conductor, it resembles perfect conductors in the THz regime [67]. Therefore, it can be considered as an isotropic material even though the magnetic field is applied. In this approximation, the conclusion of Section 2.3 can be applied. Figure 9(b) shows the dispersion curves of the lower band of SMPs waves with (B = 1 Tesla) and without the external magnetic fields. It can be found that the dispersion curves are symmetric without the magnetic field. While, when magnetic field is applied, the dispersion curves of the two propagating waves become different. The cutoff frequency of the forward-propagating mode is ω/ωp = 0.59, while that of the backward propagating mode is ω/ωp = 0.61. This means that the THz waves in the frequency region of ω/ωp = [0.59, 0.61] (corresponding to f = [1.18, 1.23] THz) can only propagate backwards.

Figure 10.

(a)-(d) FEM-simulated |Hy|2 distribution of the forward and backward propagating waves in a sub-wavelength slit. The width and length of the slit are 0.1 × 2πc/ωpand 300 μm, respectively. The incident frequency isω = 0.6ωp, which is in the one-way frequency band. (e) Transmitted intensities of the forward (corresponding to (c)) and backward propagating (corresponding to (d)) waves when 1 Tesla magnetic field is applied.

Then simulations are then conducted by the finite element method (FEM) using COMSOL Multiphysics to verify the one-way effect. The results are plotted in Figure 2 (a)-(d). When the magnetic field is not applied, the field distributions of the forward and backward propagating waves are the same (see (a) and (b), respectively). However, when there is 1 Tesla magnetic field, the forward-propagating THz wave is blocked (see Figure 2(c)), while the backward-propagating wave can still propagate through the slit (see Figure 2(d)) (there is no bright-dark field distribution in the slit as that in Figure 2(a) and (c) also confirms that no reflected SMP wave can be realized in the slit to interfere with the incident wave). The compared transmitted intensities of the forward and the backward propagating waves of Figure (c) and (d) are depicted in Figure 2(e). It can be seen the one way region located at ω = [0.592, 0.612]ωp, which agrees very well with the theoretical results.

The tuning ability of the one-way frequency band is also studied. By applying the non-retardation limit [22], i.e. substitute β > > k0 into Eq. (32), we have κ1 ≈ κ2 ≈ κ3 ≈ β, and βw > > 1. Thus the cutoff frequencies of the forward and the backward propagating modes ωVfand ωVbcan be calculated as


Figure 11.

Effects of the applied magnetic field B (a) and the permittivity of the dielectric layer (b) on the one-way frequency band.ωVrepresents the cutoff frequency.Δωis the bandwidth of the one-way band.

Therefore both ωVfand ωVbare functions of ωc, which indicate the one-way region can be tuned by the external magnetic field. The one-way bandwidth is obtained analytically as Δω = ωVf − ωVb, which increases with εd. According to Eq. (32), we calculate ωVfand ωVbversus B, and the permittivity of the dielectric layer, shown in Figure 11(a) and (b), respectively. It is found that the magnetic field affects both the cutoff frequencies of the forward and backward propagating modes. However, the bandwidth of the one-way band Δωdepends little on B, but determined by the permittivity of the dielectric layer εd. This effect is owing to the asymmetry of the mode distribution caused by the magnetic field.

Figure 12.

Field distributions of a designed THz plasmonic switch tuned by an external magnetic field. (a) the magnetic field is along +y-axis. (b) the magnetic field is along -y-axis.

Based on this one-way waveguide structure, we also proposed a THz plasmonic switch. It should be noted that if we change the propagation direction of the applied magnetic field, the dielectric tensor matrix in Eq. (1) is transposed. As a result, the one-way-propagating band will not block the forward wave, but the backward wave. According to this principle, a T-shape waveguide is designed, as shown in Figure 12. The width of the waveguide, the magnetic field intensity, and the incident frequency are the same as those in Figure 10(c) and (d). It is clearly seen that when the direction of the external MF is changed, a tunable THz plasmonic switch can be realized.

3.2. A terahertz slow-light system with tunable group velocities in a broad frequency range by SMPs

In this part, we will apply the two bands of SMPs to a THz slow light system. Slow-light technology has great application potentials in telecommunications, data processing, and light-matter interactions. Compared with traditional electronic approaches [68], plasmonic approaches are easy to achieve because its subwavelength confinement of electromagnetic (EM) fields [69]. However, most slow light systems are not tunable so far, especially in the THz frequency region. In this section, we propose a tunable THz slow-light system based on SMPs with a semiconductor-insulator-semiconductor (SIS) structure. In this structure, both the frequency and the group velocity of the slowed-down THz wave can be tuned. More importantly, due to the existence of two SMPs bands, especially the higher band which has a wider tunable bandwidth, the proposed system has a very broad tunable bandwidth.

Figure 13.

(a) Schematic structure of the THz plasmonic slow-light system. (b) Dispersion relations of the SMPs without and with an external magnetic field.

Because a plasmonic slow-light system is expected to have the same slow-light effect in both forward- and backward-propagating directions, we use a symmetric structure as shown in Figure 13(a) in which the nonreciprocal effect is eliminated. By the dispersion equation of Eq. (21), the dispersion curves of the SMPs in the structure when the external magnetic field is applied with intensities of 0, 0.5, 1 and 2 Tesla are plotted in Figure 13(b). The width of the waveguide is w = 0.1 × 2πc/ωp = 15 μm (∼1/20λof 1 THz wave). It can be seen from the figure that with the increase of the magnitude of the external magnetic field, the two bands move toward opposite directions (as indicated by the blue arrow). In addition, the shift of the higher band dispersion curve is more obvious than the lower band dispersion curve. When the magnetic field increases from 0 to 2 T, the cutoff frequency of the lower band changes from 1.9 to 0.8 THz, while that of the higher band changes from 1.9 to 4.8 THz.

Figure 14.

Slow-light effect of the structure tuned by an external magnetic field. The lower and the higher bands under the magnetic field are indicated by the blue and the pink shadows, respectively. (a) Normalized group velocity of the structure with 0 to 2 Tesla external magnetic fields (lines: Numerical results by fitting dispersion curves inFigure 13(b); triangular points: FDTD simulation results). (b) Incident frequencies versus their corresponding needed magnetic fields. (c) and (d) FDTD simulations of THz pulses propagating in the slow-light waveguide compared with that propagating in vacuum after 15 ps forf = 1.5 THz andf = 2.5 THz, respectively, when a 0.5 Tesla magnetic field is applied. The pulse is launched atx = 0. Both the lower and higher band can slow down the THz waves.

We then study the slowed-down characteristics of the structure. Since the analytical expression of the group velocity defined as vg = /cannot be obtained from Eq. (21), we calculate vgnumerically by fitting the dispersion curves in Figure 13. In Figure 14(a), the normalized group velocity vgwith respect to cas a function of the incident frequency is plotted when the external magnetic fields are 0, 0.5, 1, and 2 Tesla. It shows that vgcan achieve ∼10−6cin the structure for both the lower and higher modes in the lossless case. When the magnetic field is increased from 0 to 2 Tesla, the corresponding frequency for vg < 10−6cmoves from 1.9 to 0.8 THz for the lower band, while that of the higher band moves from 1.9 to 4.8 THz. To verify these results, finite-difference time-domain (FDTD) simulations are conducted for B = 0 and 1 Tesla, respectively (shown as the triangular points). The group velocities of the simulation results agree well with the analytical results from Eq. (21). This verifies the slow-light effects of the system. More obvious FDTD simulated results of a slowed THz pulse in the structure are shown in Figure 14(c) and (d). The incident frequencies are chosen as f = 1.5 THz and f = 2.5 THz, which are the frequencies corresponding to vg/c = 10−2 of the lower band and the higher band when a 0.5 Tesla magnetic field is applied, respectively. In the simulations, the THz pulses propagating in the slow-light system and in vacuum along the x-axis are compared. It shows that, for f = 1.5 THz, the THz pulse moves 3.3 mm in vacuum while only 0.4 mm in the structure after 15 ps. For f = 2.5 THz, the THz pulse moves 3.8 mm in vacuum while 1 mm in the structure after 15 ps. The reason on the larger simulated group velocity compared with the calculated one is that we added losses to InSb material in order to keep the simulation more stable, which may dramatically limit the achievable slow down factors and introduce losses [70]. Furthermore, the pulse is broadened because of the high dispersion of the system in the frequency region where the signal group velocity is low (the dispersion is proportional to dvg/), which could be solved by using solitons in Kerr dielectrics [71].

Although direct relation of the magnetic field intensity Band the incident angular frequency ωis difficult to obtain, it is found that the slow light region is always close to the cut-off frequency of the SMPs modes, which can be derived analytically. From the non-retarded limit of Eq. (21), the cutoff frequencies of the lower and the higher modes can be obtained by 1 + εxx + xz = 0 and 1 + εxx − xz = 0, respectively. Then we have


where ‘+’ represents ω < ωsp, ‘−’ denotes ω > ωsp. ωsp = sqrt[ωp2/(1 + εd)] is the surface plasma frequency. From Eq. (35), one can calculate the magnetic field needed to slow down the THz waves. In Figure 14(b), the calculated magnetic fields versus the frequencies of the incident THz waves are depicted. It is found that when the magnetic field increases to 6 Tesla, the group velocities of waves in the region of [0.3, 10] THz can all be decreased. Therefore, a plasmonic slow-light system with broad band tuning range is achieved.

Figure 15.

Group velocity of a monochromatic wave tuning by the magnetic field. (a) and (b)f = 1 THz (in the lower band) andf = 3THz (in the higher band), respectively. Blue lines: Results from the analytical model. Red dots: FDTD simulation results. (c) FDTD simulations of THz pulses propagating in the slow-light waveguide. The frequency of the incident wave is 1THz. When the magnetic fields are 0, 1.1, 1.3, and 1.4 Tesla, the peak of the pulse moves 0.01lc, 0.12lc, 0.24lc, and 0.44lcafter the THz pulse is launched 15 ps, respectively, wherelcis defined aslc = 15 ps × c.

From the results in Figure 14(a), it is inferred that the group velocity can also be tuned by changing the intensity of the magnetic field. We choose 1 and 3 THz in the lower and higher bands, respectively. We then calculate their corresponding group velocities dependent on B, which are shown in Figure 15(a) and (b), respectively. When the magnetic field is increased, the frequency-vgcurves corresponding to the lower band and higher bands moves to the opposite directions. Therefore, vgin the lower band decreases with the magnetic field, while vgin the higher band increases. When the magnetic field increases from 0 to 1.36 Tesla, the group velocity of 1 THz frequency deceases from 0.65cto 10−3c. For frequency at 3 THz, the required magnetic field is from 1.04 to 0.88 Tesla in order to slow down the wave from 0.23cto 0.048c. In Figure 15(c), the FDTD simulated magnetic-field-tunable group velocity of a THz pulse is depicted. The incident frequency is 1 THz. It can be found that when Bis increased, the distance Terahertz pulse moves become shorter and shorter. When B = 1.39 Tesla, it can be found that the THz pulse moves only 0.01lcafter it is launched 15 ps, where lcis the corresponding moving distance of light in vacuum. It is worth noting that the loss also increases with the magnetic field. Therefore, in addition to the broad tuning range, the group velocity can also be flexibly tuned in the proposed slow-light system.

Figure 16.

Effects of loss on the tuning properties of the slow-light system. The loss is characterized by the collision frequencyυof free carriers.

We then discuss the effects of the material loss on the tuning properties of the slow-light system. It is reported that the slowdown factor may be limited by the material losses [70]. This phenomenon is also observed with this structure. In a semiconductor, the loss is mainly caused by the collision of charge carriers, characterized by the collision frequency υin Eqs. (2)(4). For a small loss, we have υ = 0.01ωp, the group velocity vgis in the order of 10−2∼10−1c. It is increased with the loss, which can be found in Figure 16. In addition, owing to the loss, the group velocity no longer decreases monotonously with the frequency, but increases dramatically at a resonant frequency after reaching the minimum value. Therefore, the tuning mechanism of the proposed structure is still valid in a lossy system. The tunable range restricted by the material loss could be effectively compensated by using active materials [71], designing doping levels, etc.

3.3. Terahertz plasmonic slit lenses with tunable focal length

Among various plasmonic devices, planar plasmonic slit lenses (PSLs) are often used to realize integrated optical collimators [72, 73, 74]. Plasmonic slit lenses consist of a metallic slab with several nanoslits with various widths, thicknesses and material compositions. When light wave propagates through these slits, it has different phase retardations. By adjusting the materials and geometric parameters of the slits, phase control is able to be realized. Compared to other lenses, PSLs have relatively simple structures. In this part, using the magnetic field tuning ability of SMPs, we present an active THz PSL. The focal length of the PSL can be actively tuned by an external magnetic field.

Figure 17.

Schematic structure of the tunable THz PSL. The structure consists of an InSb slab tunable by an external magnetic fieldB, and perforated with 2 N-1 sub-wavelength slits. THz waves are indicated by the red arrows. They have different phase retardations after the slits, thus focusing can be realized by modulating those phases. The thickness of the slab is denoted byh. the width of thei-th slit from the middle to the two sides iswi.fldenotes the focal length of the lens. The external magnetic field B is applied along the y-axis in order to change the focal length.

The PSL structure is shown in Figure 17. It is composed a symmetric 2D InSb slab surrounded by air, and perforated with 2 N-1 slits. The thickness of the slab is h; the lens width is d; and the width of the i-th slit is denoted by wi. The incident plane wave is TM-polarized with frequency f. Therefore, each slit can be considered as an SIS waveguide structure with finite length in z-direction, or a single-mode Fabry-Perot (F-P) cavity, with the refractive index of n1 above the slit, n3 below the slit, and neff = β/k0 the effective refractive index of the slit. βis the propagating constant of SMPs that can be calculated by Eq. (21). In consequence, according to Fresnel equations, the phase retardation Δφof the magnetic field component Hythrough a slit is expressed as


where Hyiand Hyoare the incident magnetic field at the entrance and transmitted magnetic field at the exit, respectively. α = k0 × h × neff, r10 = (n1 − neff)/(n1 + neff), r12 = (n2 − neff)/ (n2 + neff), t01 = 1 − r10, t12 = 1 + r12. Therefore, according to Eq. (21), different slit widths and magnetic fields provide different propagation constants, and also the phases. In the following design procedures, without loss of generality, we set the thickness of the slab as h = 300 μm, and the incident frequency is f = 1 THz, thus εV = 45.6 + 16.4ifor B = 0 Tesla and εV = 14.3 + 6.6ifor B = 1 Tesla.

Figure 18.

(a) Dispersion relation of SMPs in an InSb-air-InSb structure. The electronic dissipation is considered. Electromagnetic wave in vacuum and magnetoplasmons (MPs) under the magnetic field ofωc = 0,ωc = 0.5ωp, andωc = 1ωpare denoted by the green, black, blue and red lines, respectively. The inset shows the enlarged view of the low-frequency region. The insulator width is set asw = 0.1 × 2πc/ωp. (b) Phase retardation of a single slit under external magnetic field of different intensity. The incident frequency is 1THz, and the thickness of the slab is 300 μm. The inset shows the corresponding increase of∆φagainst the slit width for a magnetic field from 0 Tesla to 1 Tesla.

Since phase retardation is the key factor in the design, we study the impact of the external magnetic field on ∆φfirst. The dispersion of SMPs in an InSb-air-InSb structure considering the loss of InSb is depicted in Figure 18(a), according to Eq. (21). It is found from the figure that, when the magnetic field is increased, the dispersion curve moves toward lower-frequencies. In other words, for a certain frequency, the propagation constant increases with the increase of the magnetic field, which can be seen clearly in the inset of Figure 18(a). As a result, it can be inferred from Eq. (36) that the phase retardation of the propagation mode in a slit is increased with the increase of the magnetic field. The curves of ∆φversus slit width under several magnetic field intensities are plotted in Figure 18(b), calculated by Eq. (36). It shows that for a single slit, the phase retardation becomes larger when an external magnetic field is applied. The reason is that with the increase of the external magnetic field, the negative real part of bulk dielectric constant εVincreases, which results in an increase of the effective refractive index of the slit. Therefore, the phase retardation is increased. It can also be found from Figure 18(b) that the change of the phase retardation of narrower slits is more obvious than that of wider slits under the same magnetic field.

Figure 19.

Design of a tunable THz plasmonic lens with focal length of 7λandd = 2 mm,N = 21. (a) the slit position and corresponding slit width of the designed structure. (b) the relative phase retardation of the slits under magnetic fields of 0, 0.5, 0.8 and 1 Tesla.

Then following Eqs. (21) and (36), we design a lens with focal length of fl = 7λfor B = 0, the slit positions and widths are shown in Figure 19(a). The total width of the lens and slit number are d = 2 mm and 2 N-1 = 41, respectively. Therefore, when an external magnetic field is applied, the phase curve at the slab output surface will be more convex (see Figure 19(b)) with the magnetic field. In analogous to a conventional lens, the focal length of the proposed lens will be reduced by the magnetic field.

Figure 20.

Magnetic field modulation on the THz PSL. (a), (b) |Hy|2 distributions of the structure when the external magnetic field is 0 Tesla and 1 Tesla, respectively. (c) FDTD-calculated focal length when the external magnetic field is increased from 0 Tesla to 1 Tesla.

Figure 21.

Focal length change caused by an external magnetic field increase from 0 to 1 Tesla as a function of various lens parameters. (a) Lens width changes asd = 1 mm, 1.5 mm, 2 mm, and 2.5 mm, when the designed focal length and slit number are fixed atfl = 10λ, 2 N-1 = 21, respectively; (b)Nchanges as 11, 16, 21, and 26, when the designed focal length and lens width are fixed atfl = 10λ,d = 2.5 mm; (c) designed focal lengths changes as 7λ, 8λ, 9λ, 10λ, and the length width and slit number are fixed asd = 2 mm, 2 N-1 = 41.

To verify the tunability of the PSL, we calculate the distributions of magnetic field intensity of the electromagnetic field by FDTD simulations. The results are shown in Figure 20. The magnetic field intensity distributions of the lens for B = 0 Tesla and B = 1 Tesla are shown in Figure 20(a) and (b), respectively. An obvious of focal length change is observed. From the dependence of the focal length on the intensity of applied magnetic field shown in Figure 20(c), it is found that it is changed by 3λ (from 5.92λ to 2.87λ). There is also a deviation of the calculated focal length (5.92λ) from the designed one (7λ), and some strong side lobes appear. This focal shift effect is caused by both the small Fresnel number (about 1.6 for our structure) and SMPs interactions between the slits [74]. We then change the designed parameters such as the lens width, the slit number, and designed focal length. The results are shown in Figure 21. It is found that, compared with slit number and designed focal length, the slit width dhas a greater impact on the focal length change. The reason is that for a larger lens width, the difference of the side slit width and middle slit width is greater. Therefore, the change of the phase curve on the exit plane of the slab is larger when an external magnetic field is applied.

Figure 22.

Bi-focus pattern by an external magnetic field. The parameters are same as the lens inFigure 20, exceptd = 1 mm,N = 31. (a) the slit position and corresponding slit width of the lens. (b) Phase retardation of the slits under different external magnetic fields. (c) and (d) |Hy|2 distributions under a magnetic field of B = 0 and 0.7 Tesla, respectively.

We then investigate a lens with two monotonically increased sets of slits. The lens width and slit number are set as d = 3 mm and N = 31, as shown in Figure 22(a). The designed focal length remains 7λ. The structure has two monotone intervals: [0 mm, 0.9 mm], and [0.9 mm, 1.5 mm] from the middle to the two sides. The corresponding slit phase retardations are shown in Figure 22(b). When the magnetic field increases, phase retardations of the two intervals grow asynchronously. Therefore, a discontinuous jump appears between the two intervals (see B = 0 and 0.7 Tesla for comparison). The field distribution of the transmitted wave at B = 0 Tesla and B = 0.7 Tesla (where the largest jump appears) are depicted in Figure 22(c) and (d). It shows that when the magnetic field is 0.7 Tesla, we can achieve two focal spots along the z-axis.

Figure 23.

Magnetic-field tunable lens for a dipole source imaging. The designed object and image distances are both 3λ. The source is an electric dipole with the electric field vibration direction perpendicular to thez-axis, which is represented by a white circle on the top portion of the two figures. (a) |Hy|2 distribution under a magnetic field ofB = 0 Tesla. The obtained image distance is 2.25λ. (b) |Hy|2 distribution under a magnetic field ofB = 0.8 Tesla. The obtained image distance is 0.99λ.

Last but not least, a magnetic-field tunable lens for a dipole source imaging is proposed. The source is an electric dipole with the electric field vibration direction perpendicular to the z-axis. The designed object distance and image distance are both 3λ. The distributions of magnetic field intensity for the external magnetic field of B = 0 Tesla and B = 0.8 Tesla are depicted in Figure 23(a) and (b), respectively. It shows that the obtained image distance is 2.25λand 0.99λfor B = 0 and 0.8 Tesla, respectively.


4. Summary

In this chapter, we give a brief review on surface magneto plasmons. The theory of SMPs on a plane metal/conductor surface is reviewed. Our recent research on the theories of SMPs in symmetric and asymmetric slot waveguide is also presented. We also give the applications of SMPs based on their unique and intriguing properties, such as the nonreciprocal effect, two propagating bands, and tunability by an external magnetic field. A one-way THz waveguide, a THz broadly tunable slow-light system, and a focal length tunable plasmonic slit lens are presented, which show SMPs have big possibilities in applications of tunable plasmonic devices. Although the applications of SMPs have some drawbacks so far, including large loss and strong magnetic fields, with the rapid development of plasmonics, SMPs may open a new avenue of manipulating lights in subwavelength range.

© 2018 The Author(s). Licensee IntechOpen. This chapter is distributed under the terms of the Creative Commons Attribution 3.0 License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

How to cite and reference

Link to this chapter Copy to clipboard

Cite this chapter Copy to clipboard

Bin Hu (November 5th 2018). Surface Magneto Plasmons and Their Applications, Plasmonics, Tatjana Gric, IntechOpen, DOI: 10.5772/intechopen.79788. Available from:

chapter statistics

869total chapter downloads

More statistics for editors and authors

Login to your personal dashboard for more detailed statistics on your publications.

Access personal reporting

Related Content

This Book

Next chapter

Plasmonic Enhancement of Solar Cells Efficiency: Material Dependence in Semiconductor Metallic Surface Nano-Modification

By Janusz E. Jacak and Witold A. Jacak

Related Book

First chapter

Advanced Optical Diagnostics of Atmospheric Pressure Plasma

By Qing Xiong

We are IntechOpen, the world's leading publisher of Open Access books. Built by scientists, for scientists. Our readership spans scientists, professors, researchers, librarians, and students, as well as business professionals. We share our knowledge and peer-reveiwed research papers with libraries, scientific and engineering societies, and also work with corporate R&D departments and government entities.

More About Us