Open access

Syntheses of Carbon Nanotube-Metal Oxides Composites; Adsorption and Photo-degradation

Written By

Vinod Gupta and Tawfik A. Saleh

Submitted: 25 October 2010 Published: 20 July 2011

DOI: 10.5772/18009

From the Edited Volume

Carbon Nanotubes - From Research to Applications

Edited by Stefano Bianco

Chapter metrics overview

11,775 Chapter Downloads

View Full Metrics

1. Introduction

The unique chemical, physical and mechanical properties of carbon nanotubes (CNTs) have stimulated extensive investigation since their discovery in the early 1990s (Iijima, 1991). The primary research interests focus on the development of simple and cost effective methods for the synthesis of CNTs. To synthesize single wall carbon nanotubes (SWCNT) and multi wall carbon nanotubes (MWCNT), various techniques have been developed. Examples are laser ablation, arc discharge, and chemical vapor deposition (CVD). However, CVD is considered to be more productive method to produce CNTs with acceptable price. Therefore, the extraordinary properties of CNTs and the continuous decrease in their price make them potentially useful in a wide range of applications like in catalysis, photocatalysis and adsorption. The adsorption properties of CNTs depend on different factors such as their large specific surface area, highly porous and hollow structure, light mass density and strong physical interaction ability.

Recently, the applicability of CNTs as adsorbent has been extensively investigated. The applications of CNTs for the removal of pollutants from aqueous solutions have been studied. Numerous experimental studies have already been carried out on the adsorption of heavy metals and hazardous organic materials (Li, et al., 2002; Li, et al., 2003; Chen, et al., 2006; Hyung and Kim, 2008; Goering, et al., 2008).

For further enhancement the adsorption ability of CNTs, purification and activation or functionalization of CNTs is essential and can be performed via oxidation treatment (Cho, et al., 2010; Shao, et al., 2010). Purification is necessary to remove the impurities, like catalyst particles, soot, amorphous carbon and other forms, which are often found, mixed with CNTs. Impurities can reduce the adsorption by their coating on the surfaces of CNTs, and as a result influencing the adsorption on the external surface of the nanotubes (Agnihotri et al., 2006). The enhancement in the adsorption ability of CNTs via oxidation treatment with oxidizing agent, such as nitric acid, hydrogen peroxide, potassium permanganate, or a mixture of nitric acid and sulfuric acid, is most probably ascribed due to an increase in hydrophilicity of CNTs. Oxidation treatment of CNTs results in creating new functional groups on the surface of nanotubes.

In recent years, metal oxides nanoparticles supported on carbon nanotubes have been extensively studied and found to be effective adsorbent for the removal of heavy metal ions and hazardous organic chemicals from water; and also as catalysts. The synthesis methodology of such materials will be discussed in the followed section. The discussion will highlight the synthesis process starting with activation or functionalization of CNTs as a preliminary step for the synthesis of such materials.


2. Synthesis strategy

The formation of carbon nanotubes/metal oxide (CNT/MO) composites is both of fundamental and technological interest since the composite combines the unique properties of CNTs and metal oxide nanoparticles, and in addition exhibit some new extraordinary properties caused by the interaction between them (Eder, D., 2010); Chu, et al., 2010). Thus, a new class of nanocomposites can be made with extraordinary properties meeting a wide range of applications in different disciplines. For example, alumina is one of the most widely used ceramic materials because of its high hardness, good oxidation resistance and chemical stability. However, its applications are limited because of its low fracture toughness. CNTs have been widely used to reinforce and increase the fracture toughness of alumina owing to their unique one dimensional structure with robust mechanical and thermal properties (Chan, et al., 2005).

Various approaches are used to synthesize CNT/MOs composites. This includes hot pressing of composite powder, pressureless sintering technique, direct in-situ growth, in situ CVD synthesis route, high-intensity ultrasonic radiation method, assembling pre-synthesized metal oxide nanoparticels as building blocks on CNTs, spontaneous formation of metal oxide nanoparticels on CNTs, thermal decomposition of metal oxides precursor directly onto the surface of carbon nanotube, hydrothermal crystallization, sol–gel followed by spark plasma sintering process, surfactant wrapping sol–gel method, chemical precipitation and controlled heteroaggregation method (Liu et al., 2009; Zhang et al., 2010; Keshri et al., 2010; Datye et al., 2010; Zhen et al., 2007; Flahaut et al., 2000; Lupo et al., 2004; Gupta et al., 2011; Zhang et al., 2006; Gao et al., 2008; Chan et al., 2005; Yang et al., 2009; Estili and Kawasaki, 2008).

Over all, the methods based on what is called wet chemistry are perhaps the most widely utilized methods in everyday chemistry. One of the most important reasons of their popularity is simplicity and cost comparing to others. However, in these methods, activation or functionalization of CNTs is a primary step that should be conducted before the synthesis and preparation of CNT/MO nanocomposite materials. Functionalization of CNTs plays an important role in facilitating the binding, embedding or loading nanoparticels on the surface of nanotubes since it introduces chemical functional groups to the surface of nanotubes. The successful in functionalization of the nanotubes is the first step to properly prepare the nanocomposite.

2.1. Functionalization of CNTs

Activation or functionalization of CNTs by oxidation treatment introduces chemical functional groups. It can be performed using oxidizing agents such as nitric acid, sulfuric acid, a mixture of sulfuric acid and nitric acid, potassium permanganate, sulfuric acid in presence of potassium permanganate, hydrogen peroxide in presence of nitric acid, hydrogen peroxide, ozone, an oxygen-based atmosphere by an inductively coupled plasma or microwave energy and water (Cuentas-Gallegos et al., 2006; Wang et al., 2009; Smith et al., 2009; Lu et al., 2008; Otvos et al., 2006; Aviles et al., 2009; Haydar et al., 2000; Peng et al., 2011; Ionescu et al., 2006; Hojati-Talemi & Simon, 2009).

Treatment with different oxidizing agents might introduce different functional groups on the CNTs surface including alcoholic, carboxylic, aldehydic, ketonic, and esteric oxygenated functional groups, see Fig.1. Hydroxyl groups (b) on the edge of nanotube could be of phenolic character. Oxygen could be substituted for edge carbon atoms in xanthene- or ether-type (d). Carboxyl groups (a) might give carboxylic anhydrides (e) if they are close together. Also, carbonyl groups might condense to lactone groups (f) or form lactols (g) if they are in close to hydroxyl groups or carboxyl groups. The existence of carbonyl groups could be isolated (c) or arranged in quinone-like structure (h). The groups (a, b, e f, and g) have weak acidic character. The acidity of o-CNTs can be determined by acid-base titration method or Boehm titration (Boehm, 1994).

Figure 1.

Possible structures of oxygen-containing groups on the carbon nanotube surface

Synthesis of CNT/MO requires the nanotubes’ surface to have mainly alcoholic and carboxylic functional groups which can facilitate the binding of the nanoparticles into the nanotubes. Over other methods, treatment of CNTs by nitric acid or mixtures of sulfuric acid and nitric acid have been expected to mainly graft carboxylic and alcoholic functional groups onto the CNTs surface (Martinez et al., 2003; Chiang et al., 2011). It is also worth mentioning that the contents of carboxylic and alcoholic groups increase with increasing oxidation time.

The characterization of the presence of functional groups on the surface of nanotube and the efficiency of functionalization on nanotubes can be professionally carried out by various instruments like transmission electron microscope (TEM), field emission scanning electron microscope (FESEM), energy dispersive X-ray (EDX), Raman spectroscope, thermogravimeter (TGA), and fourier transformed infrared spectroscope (FT-IR) and X-ray photoelectron spectroscope (XPS).

Morphology and structure of CNTs is characterized by TEM and FESEM. The impurities and defects such as carbonaceous materials, amorphous carbon coatings and catalyst particles are observed as black dots inside the body of nanotubes or on its surface. TEM provides sufficient resolution for the nanotubes’ length and diameter distribution; and opening of the ends of nanotubes. TEM and SEM can allow observing if damage to the surface of CNTs after chemical treatment has occurred and observing the presence of different materials around nanotubes, if any. EDX measurements are used for quantitative representation of the components in the CNTs sample. After oxidation process of CNTs, it is expected that EDX reflect more oxygen on the CNTs sample as a result of grafting new oxygen-containing functional groups.

FT-IR is used to analyze the chemical bonding and type of functional groups grafted onto the nanotubes. The application of FTIR in the study of the surface chemistry of nanotubes can provide direct means to observe the interactions occurring at the surface during adsorption and to determine the structure of the adsorbed species. The FTIR spectra of oxidized CNTs (o-CNTs) exhibit various characteristic bands. Example of FTIR spectra of o-MWCNTs is shown in Fig. 2.

Figure 2.

FTIR spectra of MWCNT oxidized with mixtures of H2SO4/HNO3 at 100 0C.

The IR spectrum of o-MWCNTs, Fig. 2, shows absorption peak at 1715 cm−1 corresponding to the stretching vibration of C=O from the carboxylic groups (–COOH). The carbonyl characteristic peak is also observed at about 1636 cm-1 and can be assigned to the carbonyl group from quinine or ring structure. The broad peaks at 1180 cm−1 could be assigned to C–O stretch from phenol or lactone groups; and also to C–C bonds. The band at 2910 cm-1 and 2850 cm-1 corresponds to CH stretching. The peak at around 3400 cm−1 corresponds to OH stretching. This peak can be assigned to the hydroxylic group of moisture, alcohol, or carboxylic groups. The aromatic C=C stretch is observed at around 1580 cm−1 in spectra of both pristine CNTs and o-CNTs.

XRD is used in order to ascertain the quality and crystalline nature of nanotubes as opposed to amorphous carbon materials. Fig. 3 shows the X-ray diffraction pattern of the o-MWCNTs. The intensity counts versus two theta. The angle is between the incident and scattered beams. The pattern shows intense peak at 2θ = 25.9o corresponding to the (002) reflection. Compared to the normal graphite, 2θ = 26.5o, this peak shows a downward shift; which is attributed to an increase in the sp2, C=C layers spacing (Zhang et al., 2002). The other diffraction peaks, are at the angles 2θ of 42.7o, 43.9o, 53.5o and 77.5o and indexed to the (100), (101), (004) and (110) reflections.

Figure 3.

XRD patterns of MWCNT oxidized with HNO3 at 120 0C

Raman spectroscopy is frequently used to characterize CNTs. It reflects different characteristic spectra for sp3, sp2, and sp carbons, as well as for disordered sp2. Two bands is usually observed showing the characteristics of CNTs. The bands point the graphite band (G band), at about 1580 cm-1, and the disorder and defects of the structure, named D band, at around 1330 cm-1. The ratio between the intensity of D band and G bands (ID/G), is related to the degree of disorder of the CNTs. When oxidation treatment of CNTs is performed, these characteristic peaks should still be identified to indicate that the treatment process does not damage the nanotube structure. An increase of the ratio values (ID/G), of CNTs after oxidation treatment, ensures that the functional groups are covalently grafted with the CNTs. It indicates clearly that the oxidation treatments of CNTs breaks some of its bonds and inserts new chemical bonds, interpreted as defects on the nanotube structure (Osorio et al., 2008).

The TGA analysis of CNTs presents good indication of the functionality. o-CNTs starts decomposing earlier than the pristine-CNTs. The thermal stability of the pristine CNTs decreases with increasing oxidative functionalisation. The decrease of the initial burning temperature of the o-CNTs is closely related to the introduction of the defects and functional groups upon oxidation treatments. This is attributed to the earlier decomposition of the grafted carboxylic groups on the nanotubes. For example, the decomposition of the pristine-MWCNTs occur (TGA under flowing nitrogen, temperature range of 90–860 °C, at rate of 15 °C/min) at the onset temperature of 639 °C while of o-MWCNTs, it occurs at 627 °C (Okpalugo et al., 2005).

The XPS survey scan of CNTs is used to reveal the chemical compositions of the uppermost surface of the nanotubes. The major peaks due to the C1s and O1s photoelectrons can be observed in the scan. For example, the change in the C1s and O1s can be monitored and the O/C atomic ratios can be calculated to indicate the degree of surface oxidation. General conclusion is that the higher the O/C ratio, the more the oxygen atoms are bound to the nanotubes in the oxidation treatment. In addition, XPS O1s peaks demonstrate additional information on the nature of the surface oxygen-containing groups including the contribution of chemisorbed H2O.

2.2. Synthesis and characterization of carbon nanotube/metal oxides composites

Carbon nanotubes/metal oxide (CNT/MO) composites can be prepared by various methods as mentioned earlier in this section. Here, the focus is on the wet chemistry methods where the CNTs act as nucleation sites for the metal oxides. In the first section, the synthesis of CNT/MO will be discussed. In the second section, the characterization of the CNT/MO nanocomposites using different characterization tools will be described with highlight on the interpretation of some experimental data.

2.2.1. Synthesis of CNT/MO composites

Generally, the o-CNTs are dispersed in an appropriate solvent like acetone, ethanol, propanol or n-methyl-2-pyrrolidone; untile well homogeneous suspension is formed. The dispersion can be achieved via sonication; some surfactants are used for dispersion. At the same, the precursor of the metal oxide is dissolved in a suitable solvent. Then, the latter is drop-wise added into the dispersed o-CNTs; and the mixture is sonicated for a while, then, magnetically stirred for some time. After that, the suspensions’ mixture is transferred into round-bottomed flask and refluxed at high temperature; say 120- 200 0C, in oil bath or hot plate, with magnetic stirring, for specific time depends on the type of metal oxide. After that, the system is allowed to cool naturally to room temperature. Then, the mixture is filtered and washed with suitable solvent like distilled water and ethanol several times. After that, the resulted composite is dried at 100 0C. Final step in the strategy of synthesis is the calcinations process of the composite at various temperatures and for different times. The end product consists of CNTs coated, or embedded with nano-sized metal oxide; see the visualization illustration in Fig. 4.

The ratio of MO nanoparticels on CNTs is controlled by the initial concentrations and the type of the precursors of the metal ions. It is worth mentioning that the high ratio of MO would result in the agglomerating of the nanoparticles on the nanotubes. Additionally, the

Figure 4.

Illustration representation of the synthesis of Carbon nanotubes/metal oxide (CNT/MO) composites

distribution of nanoparticels on the surface of the nanotubes is controlled by the synthesis treatment including the addition of the precursors into well dispersed o-CNTs, the extent of treatment oxidation of pristine CNTs. The nanoparticle size is controlled by the calcinations temperature and time. The rate of increasing the calcinations temperatures can also have an effect on the nanoparticle size. Controlling these parameters can yield a composite of uniformly dispersed metal oxide nanoparticels on the surface of the nanotubes.

As illustrated in Fig. 5, the nanotube surface presents polar groups like hydroxyl or carboxyl groups which are able to interact with the oxygen of the metal oxide, like aluminum oxide. The interaction could be through hydrogen bonding, or the oxygen atoms of hydroxyl or carboxyl groups interact with aluminum atoms through the pair of electrons on the oxygen atoms. The formation of chemical bond is also possible.

2.2.2. Characterization of CNT/MO composites

Characterization of the as–prepared carbon nanotube/metal oxides (CNT/MO) nanocomposite is performed by means of different characterization tools like high resolution transmission electron microscope (HRTEM), field emission scanning electron microscope (FESEM), energy dispersive X-ray spectroscopy (EDX), thermogravimetric analysis (TGA), Raman spectroscope, UV–vis spectrometer and fourier transformed infrared spectroscope (FT-IR), X-ray photoelectron spectroscope (XPS) and photoluminescence (PL) technique; in addition to electrochemical techniques. The techniques are complementary.

Figure 5.

Structural representative of bossible ineraction between Al2O3 and carbon nanotube in MWCNT/Al2O3 nanocomposite.

They can be used to investigate the chemical and physical properties of the nanocomposites. In the following paragraphs, the importance of each technique for the characterization of the composites will be highlighted with detailed examples of some experimental results.

HRTEM image indicates the shape and distribution of nanparticles on the surface of the nanotubes. The average size and diameters of the nanparticles can also be determined from the TEM images. Particularly, TEM is employed to observe the loading state of the nanocomposites. Specifically, TEM images show the surface of the nanotubes coated, decorated or embedded with the nanoparticles. It might be also used to compare the surfaces o-CNTs with that of CNT/MO nanocomposite in term of the roughness and compact.

SEM micrograph is used to investigate the surface morphology and the general morphological features of the prepared composites nanomaterials. It also reveals the uniformity of dispersion of the nanoparticles on the nanotubes. The average particle size can also be calculated. SEM image can be taken with low or high magnification. As an example, Fig. 6 presents the low magnification SEM to reflect the morphology of the CNT/alumina nanocomposite in which CNTs seem to be decorated with aluminum oxide nanomaterial.

The EDX or EDS measurements are usually used to confirm the percentage, the atomic ratio, of components on the surface of the nanocomposites. It should be noticed that EDX spectrum is better to be measured for large surface area of the sample for better representation, in other words, lower errors. That means the SEM image from which EDX is measured could be in µm scale, as shown in the inset of Fig. 7. However, it is not expected to get the exact atomic ratio of the metal oxides since some oxygen contribution comes from the oxygen-containing functional groups, such as carbonyl or carboxyl groups, on the surface of CNTs.

Figure 6.

Field emission scanning electron microscope (FESEM) of MWCNT/Al2O3 nanocomposite

Figure 7.

Energy dispersive X-ray (EDX) spectrum of the area indicated in the Inset: low magnification scanning electron microscope (SEM) of MWCNT/Al2O3 nanocomposite; Inset: Table presents the atomic ratio, percentage of the components in the nanocomposite.

Thermogravimetric analysis is used to confirm the presence of metal oxides particles in the nanocomposite. From TGA of CNT/MO nanocomposites, it is expected to have initial weight loss between 250 to 500 °C and can be attributed to condensation reactions of metal-hydroxyl residual groups on the surface of the prepared nanocomposites materials (Amais et al., 2007).

XPS analysis is also of important. In the C1s XPS spectra, the main peak is usually observed at 284.6 eV which is attributed to the C–C bonds. Additional peaks are observed at 285.8 eV, 286.8 eV and 289.3 eV; and are assigned to C–O and C=O bonds; and COO groups (Jitianu et al., 2004). The shift of these peaks to higher binding energy could be indicative of binding of metal oxide to the nanotubes.

The XRD patterns are used to characterize the crystalline structure of the CNT/MO nanocomposites. Comparing the XRD patterns of o-CNTs and CNT/MO nanocomposite, the characteristic peaks for o-CNTs at the positions of 25.9o and 43.9o, see Fig. 3, might disappear or become thinner in the XRD pattern of the nanocomposites. The reason is that these peaks in the nanocomposites are overlapped by the peaks of the metal oxide nanoparticles. For example, in the XRD pattern of MWCN/TiO2 composites, only anatase and brookite phases attributed to TiO2 have been observed. The possible explanation is that the main peak of nanotube at 25.9o is masked with the main peak of anatase TiO2 at 25.4o since their positions are so close. Additional is that the crystalline extent of carbon nanotube is lower than the crystalline extent of TiO2, leading to the shielding of the peaks of CNTs by those of TiO2 (Yu et al., 2005). Example is the XRD pattern, Fig. 8, of MWCNT/WO3 nanocomposite. In this pattern the diffraction peaks revealed the presence of hexagonal and orthorhombic tungsten oxide nanoparticles. Therefore, the presence of tungsten oxide nanoparticles peaks might lead to the mask the characteristic peak of the nanotubes at 2 θ equal to 25.8 degree.

Figure 8.

XRD patterns of MWCNT/WO3 nanocomposite.

Raman spectroscopy is a powerful characteristic technique that is employed to distinguish between the characteristic peaks of TiO2 and those of CNTs since peaks from each components; nanotube and metal oxide are in most cases separated in frequency, and thus the phases are distinguishable. It is worth mentioning that to run samples on Raman, the energy power should be as low as possible to prevent the effect on the nanotube absorption and get good results. The energy power is preferably to be selected between 10 and 100 mW.

Figure 9.

FTIR spectra of MWCNT/WO3 nanocomposite.

Comparing the IR spectra of o-CNTs and the nanocomposite is of interest. The comparison should focus on two characteristic peaks. The first peak is the characteristic peak of the pure metal oxide nanoparticels, which is usually appear between around 400 and 700 cm-1 depends on the type of metal oxide. For example this peak appear at 700 cm-1 in the IR spectrum of WO3 nanoparticles. The shift of this peak in the spectra of nanocomposite could be attributed to strong bond between the metal and the nanotube through oxygen-containing group. The second peak is the band assigned to C=O stretching vibration. The shift of this peak toward lower wavenumber is an indication of the carboxylic ion binding between nanoparticles and the nanotube. Example is the IR spectrum of MWCNT/WO3 nanocomposite, depicted in Fig. 9. This spectrum shows the shift of the peak of W-O covalent bond from 701cm-1 to 770cm-1. It also shows the shift of the band assigned to C=O stretching vibration from 1670 to 1606 cm-1, reader can compare Fig. 9 with Fig. 2.


3. Applications of CNT/MO nanocomposites

CNT/MO nanocomposites are new generation with interesting properties that not only combine the properties CNTs and MOx but also hold new properties caused by the interaction between them. In addition, combine these materials in a composite can overcome some disadvantages. For example, metal oxide nanoparticles have a tendency to agglomerate because of their dangling bonds. In the composite, dispersion of the nanoparticles on the surface of the nanotube prevents their agglomeration. It should be noticed that the aggregation of nanotubes in aqueous media is solved by functionalization. As a result, the composites attractive wide applications compared with the isolated nanoparticles because CNTs act as carrier to stabilize the nanoparticles, maintaining their integrity. Examples of the fields of applications are water treatment, environment, catalysis and others. Examples of the nanocomposites that can be prepared are Ti2O3, ZnO, WO3, Fe2O3, SnO2, CeO2, Al2O3, ZrO2, SiO2, V2O4 and Er2O3 on CNTs. In the next section, we will discuss the application of the composites as adsorbents followed by the discussion of their applications to enhance catalytic activity in the second section. A mechanism will be discussed to explain the enhancement of the photocatalytic properties of the nanocomposite.

3.1. Nanocomposites as sorbents

The sorption applications of CNT/MO nanocomposites to tackle environmental pollution problems have received considerable attention. The nanocomposites provide chemically inert surfaces with high specific surface areas for physical adsorption. They have relatively uniform structure, providing more adsorption sites.

For the application of the nanocomposite as sorbents in batch sorption experiments, different parameters need to be optimized, such as agitation speed, contact time and adsorbent dosage, pH of the aqueous media, initial concentration of the pollutant, effect of presence of other cations and anions in the media. Also, for the application of the nano-composite as adsorbents in fixed bed column experiments, different parameters need to be optimized, such as flow rate, the bed thickness and diameters, pH of the aqueous media, initial concentration of the pollutant, effect of the presence of other cations and anions in the media.

For example, MWCNT/alumina nanocomposite has been reported to be an effective sorbent for the removal of lead ions from aqueous solution with pH range of 3-7. The efficiency of the nanocomposite has been tested in batch mode and fixed bed, column mode. It has been reported that by increasing agitation speed, contact time and adsorbent dosage the amount of the removal is increased. The percentage of lead removal increases by decreasing the flow rate and increasing the bed thickness (Gupta et al., 2011). CNT-iron oxides magnetic composites has been successfully applied as adsorbent for removal of different targets from water such as Pb(II), Cu(II) (Peng et al., 2005), Ni(II), Sr(II) (Chen et al., 2009b) and Cr(III) (Gupta et al., 2011). The incorporation of iron oxide magnetite with CNTs has been used for europium adsorption. This composite is potentially a promising to facilitate the separation and recovery of CNTs from solution with magnetic separation technique. The beauty of this method is that CNTs do not become another source of contamination (Chen et al., 2009a). Also, the magnetic MMWCNT nanocomposite has successfully utilized as an adsorbent for removal of cationic dyes from aqueous solutions (Gong et al., 2009).

The adsorption ability of manganese oxide-coated carbon nanotubes has been utilized for the removal of lead(II) from aqueous solution. The effect of metal oxide nanoparticels loading level has been investigated. It has been reported that the adsorption capacity of Pb(II) increased with increasing MnO2 load because of the availability of more binding sites. The optimum reported load is 30 wt% (Wang et al., 2007).

3.2. Nanocomposites as catalysts

CNTs have been widely used to support and enhance the catalytic activity of metal oxides. CNT/WO3 nanocomposite has been utilized as catalysts for C6 olefin skeletal isomerization in different activation conditions. Comparing with tungstated zirconia, the nanocomposite shows higher skeletal isomerization selectivity at 200 °C with higher conversion level without deactivation. The optimum load of WO3 on CNTs was reported to be 5% (Pietruszka et al., 2005). Such composite shows also higher photocatalytic activity comparing with WO3 nanoparticels. The composite has been applied for the degradation of dye. It could be concluded that doping WO3 into CNTs enhances the photocatalytic activity (Wang et al., 2008).

Another comparison of the photocatalytic activity has been conducted between TiO2 and TiO2/CNTs composites for acetone degradation. It has been noticed that the presence of a small amount of CNTs can enhance photocatalytic activity of TiO2 (Yu et al., 2005). This is supported by another study in which photocatalytic activity of TiO2/SWCNT composite has been investigated degradation of organic dyes and 2,6-dinitro-p-cresol. High photocatalytic activity of the TiO2/SWCNT composite has been observed comparing with that of TiO2 nanoparticles. This could be attributed to the synthetic effect of larger surface area, smaller crystalline size, and the formation of the chemical bond between TiO2 and the nanotube which improve interface contact (Zhou et al., 2010; Wang et al., 2009). It has been reported that the bond of carbon–oxygen–titanium can extend the light absorption to longer wavelengths and therefore potentially leading to the improvement of the photocatalytic activity (Woan et al., 2009).

MWCNTs has been used to enhance the catalytic activity of zinc oxide for the acetaldehyde removal (Saleh et al., 2011) and cyanide degradation in aqueous media (Saleh et al., 2010) under UV irradiation. Zinc oxide nanoparticels are embedded on multiwall carbon nanotubes via thermal hydrolysis method. Great enhancement in photocatalytic activity has been recorded by the MWCNT/ZnO nanocomposite.

3.2.1. Mechanism

The enhancement in photocatalytic performance of the CNT/MO nanocomposites can be rationally explained in a mechanism based on two criteria. The first is adsorption ability of the nanotubes since the adsorption is a key process in the catalytic destruction of organic pollutants. While the second is the electron transfer from nanoparticels into the nanotubes, in other words the electron injection (Xu et al., 2010 & Martinez et al., 2011). In general, irradiation of metal oxide semiconductor with a photon of sufficient energy, greater or equal to band gap energy could promote an electron from valence band (VB) to conduction band (CB). The promoted electron leaves a vacancy in the valence band creating positive hole which can react with hydroxyl forming a powerful oxidant or a hydroxyl radical. The promoted electrons reduce dissolved oxygen to produce superoxide anion radical. The hydroxyl radical (OH) and superoxide anion radical (O2•-) oxidize the target.

CNTs can adsorb oxygen molecule on its surface thus the promoted electrons in CB might directly react with the adsorbed oxygen molecule and form superoxide anion radical. This will increase the number of radicals ready for reacting with the target. Also CNTs can adsorb the target which is considered to be the first step in the degradation since the pre-adsorption of the target on the surface of catalyst particles is a prerequisite for efficient photo-degradation (Zhao et al., 1998).

On the other hand, the strong interaction and formation of ester bonds between the metal and the nanotube leading in a close contact which offers an effective route of electron transfer from the CB in to the nanotube. This can reduce the recombination of photo-generated electron-hole pairs. This conclusion is supported by the higher activity of the CNT/MO composites and by being CNTs relatively good electron acceptors while semiconductors as good electron donor under illumination (Subramanian et al., 2004; Geng et al., 2008).


4. Conclusion

In this chapter we discuss the preparation of the new class of CNT/MO nanomaterials that offer great potential applications in different fields. The chapter has analyzed the methodology of functionalization and activation of the nanotubes as a first step for preparation of CNT/MO nanocomposites. The details of functional groups characterization have also been discussed. The synthesis of CNT/MO nanocomposites is detailed with the characterization interpretation. Some case-studies have been carried out referring to a realistic use of CNT/MO nanocomposites as adsorbents that have excellent adsorption ability for many kinds of pollutants like inorganic and organic compounds.

The advantage is that CNTs provide large number of nucleation centers available on its surface for receiving the nanoparticles and preventing their agglomeration. This makes such material not only good in adsorption but also in enhancement of the catalytic activity. The reason given for the high catalytic performance is the optimum dispersion of MO on the CNTs. The mechanism of enhancing the photo-catalytic activity is discussed based on adsorption ability of the nanotube and the transfer of promoted electrons from metal oxide to CNT. The most important processing issue is the interfacial strength between the CNTs and the MO nanoparticles.

Over the last years, much progress has been made in adsorption applications of CNT/MO nanocomposites. In spite of high costs, using CNTs as adsorbents may be advantageous in future owing to their high adsorption capacities. However, there are still much to do to enhance CNT/MO nanocomposites’ adsorption properties in future. Efforts in synthesis methods to develop a cost effective way of CNTs production are required. Investigations on CNT/MO nanocomposites on applications in adsorption and catalysis are recommended.



Authors acknowledge the support of King Fahd University of Petroleum and Minerals, (KFUPM) Dhahran, Saudi Arabia, for this work.


  1. 1. AgnihotriS.MotaJ. P. B.Rostam-AbadiM.RoodM. J. 2006 Adsorptionsiteanalysis of impurity embedded single-walled carbon nanotube bundles, Carbon 44 23762383 .
  2. 2. AmaisR. S.RibeiroJ. S.SegatelliM. G.YoshidaI. V. P.LuccasP. O.TarleyC. R. T. 2007 Assessment of nanocomposite alumina supported on multi-wall carbon nanotubes as sorbent for on-line nickel preconcentration in water samples, Separation and Purification Technology 58 122128
  3. 3. AvilesF.Cauich-RodríguezJ. V.Moo-TahL.May-PatA.Vargas-CoronadoR. 2009 Evaluation of mild acid oxidation treatments for MWCNT functionalization, Carbon 47 29702975 .
  4. 4. BoehmH. P. 1994 Some aspects of the surface chemistry of carbon blacks and other BoehmH. P. (1994). Some aspects of the surface chemistry of carbon blacks and other carbons. Carbon .s. Carbon 32 75969 .
  5. 5. ChanB. M.ChaS. I.KimK. T.LeeK. H.HongS. H. 2005 Fabrication of carbon nanotube reinforced alumina matrix nanocomposite by sol-gel process, Materials Science and Engineering A 395 124128
  6. 6. ChenC. L.WangX. K.NagatsuM. 2009a Europium Adsorption on Multiwall Carbon Nanotube/Iron Oxide Magnetic Composite in the Presence of Polyacrylic Acid, Environ. Sci. Technol. 2009 43 23622367
  7. 7. ChenC.JunHu.DadongShao.JiaxingLi.XiangkeWang. 2009b Adsorption behavior of multiwall carbon nanotube/iron oxide magnetic composites for Ni(II) and Sr(II), Journal of Hazardous Materials 164923
  8. 8. ChenC. L.WangX. K. 2006 Adsorption of Ni(II) from aqueous solution using oxidized multiwall carbon nanotubes, Ind. Eng. Chem. Res. 45 91449149 .
  9. 9. ChiangY.LinW. H.ChangY. C. 2011 The influence of treatment duration on multi-walled carbon nanotubes functionalized by H2SO4/HNO3 oxidation, Applied Surface Science 2572401
  10. 10. ChoH. H.WepasnickK.SmithB. A.BangashF. K.FairbrotherD. H.BallW. P. 2010 Sorption of aqueous Zn[II] and Cd[II] by multiwall carbon nanotubes: the relative roles of oxygen-containing functional groups and graphenic carbon, Langmuir 26 967981 .
  11. 11. ChuH.WeiL.CuiR.WangJ.LiY. 2010 Carbon nanotubes combined with inorganic nanomaterials: Preparations and applications. Coord Chem Rev 2010, 254: 1117 EOF1134 EOF -1120.
  12. 12. Cuentas-GallegosA. K.Martínez-RosalesR.RincónM. E.HirataG. A.OrozcoG. 2006 Design of hybrid materials based on carbon nanotubes and polyoxometalates, Opt. Mater. 29 126133 .
  13. 13. DatyeA.WuK. H.GomesG.MonroyV.LinH. T.JozefV.VanmeenselK. 2010 Synthesis, microstructure and mechanical properties of Yttria Stabilized Zirconia (3YTZP)- Multi-Walled Nanotube (MWNTs) nanocomposite by direct in-situ growth of MWNTs on Zirconia particles, Composites Science and Technology 70 20862092
  14. 14. EderD. 2010 Carbon Nanotube-Inorganic Hybrids. Chem Rev. 110 13481352 .
  15. 15. EstiliM.KawasakiA. 2008 An approach to mass-producing individually alumina-decorated multi-walled carbon nanotubes with optimized and controlled compositions, Scripta Materialia 58 906909
  16. 16. FlahautE.PeigneyA.LaurentC.MarlieRe. C.ChastelF.RoussetA. 2000 Carbon nanotube-metal-oxide nanocomposites: microstructure, electrical conductivity and mechanical properties, Acta Mater. 48 38033812
  17. 17. GaoB.PengC.ChenG. Z.PumaG. L. 2008 Photo-electro-catalysis enhancement on carbon nanotubes/titanium dioxide (CNTs/TiO2) composite prepared by a novel surfactant wrapping sol-gel method, Applied Catalysis B: Environmental, 85 1723
  18. 18. GengQ.GuoQ.CaoC.WangL. 2008 Investigation into NanoTiO2/ACSPCR for Decomposition of Aqueous Hydroquinone, Ind. Eng. Chem. Res. 47 25612568
  19. 19. GoeringJ.KadossovE.BurghausU. 2008 Adsorption kinetics of alcohols on single wall carbon nanotubes: an ultra high vacuum surface chemistry study, J. Phys. Chem. C 112 1011410124 .
  20. 20. GongJ. L.WangB.ZengG.YangC.NiuC.NiuC.ZhouW.LiangY. 2009 Removal of cationic dyes from aqueous solution using magnetic multi-wall carbon nanotube nanocomposite as adsorbent, Journal of Hazardous Materials 164 15171522
  21. 21. GuptaV. K.AgarwalS.SalehT. A. 2011 Synthesis and characterization of alumina-coated carbon nanotubes and their application for lead removal, Journal of Hazardous Materials 185 1723
  22. 22. GuptaV. K.AgarwalS.SalehT. A. 2011 Chromium removal by combining the magnetic properties of iron oxide with adsorption properties of carbon nanotubes, Water Research 45 22072212
  23. 23. HaydarS.Moreno-CastillaC.Ferro-GarcíaM. A.Carrasco-MarínF.Rivera-UtrillaJ.PerrardA.JolyJ. P. 2009 Regularities in the temperature-programmed desorption spectra of CO2 and CO from activated carbons, HaydarS.Moreno-CastillaC.Ferro-GarcíaM. A.Carrasco-MarínF.Rivera-UtrillaJ.PerrardA.JolyJ. P. (2009). Regularities in the temperature-programmed desorption spectra of CO2 and CO from activated carbons, Carbon . 38 2000 12971308 .
  24. 24. Hojati-TalemiP.SimonG. 2009 Microwave-based treatments for multi-walled carbon nanotubes,, Phys. Status Solidi C 6, 10: 2170-2173
  25. 25. HyungH.KimJ. H. 2008 Natural organic matter (NOM) adsorption to multi-walled carbon nanotubes: effect of NOM characteristics and water quality parameters, Environ. Sci. Technol. 42 44164421 .
  26. 26. IijimaS. 1991 Helical Microtubules of Graphitic Carbon, Nature 354 5658
  27. 27. IonescuR.EspinosaE. H.SotterE.LlobetE.VilanovaX.CorreigX.FeltenA.BittencourtC.Van LierG.CharlierJ. C.PireauxJ. J. 2006 Oxygen functionalisation of MWNT and their use as gas sensitive thick-film layers, Sensors and Actuators B 11336
  28. 28. JitianuA.CacciaguerraT.BenoitR.DelpeuxS.BeguinF.BonnamyS. 2004 Synthesis and characterization of carbon nanotubes-TiO2 nanocomposites, JitianuA.CacciaguerraT.BenoitR.DelpeuxS.BeguinF.BonnamyS. (2004). Synthesis and characterization of carbon nanotubes-TiO2 nanocomposites, Carbon 42 11471151
  29. 29. KeshriA. K.HuangJ.SinghV.ChoiW.SealS.AgarwalA. 2010 Synthesis of aluminum oxide coating with carbon nanotube reinforcement produced by chemical vapor deposition for improved fracture and wear resistance, KeshriA. K.HuangJ.SinghV.ChoiW.SealS.AgarwalA. (2010). Synthesis of aluminum oxide coating with carbon nanotube reinforcement produced by chemical vapor deposition for improved fracture and wear resistance, Carbon . 48 431442 .
  30. 30. LiY. H.DingJ.LuanZ. K.Di Z. C.ZhuY. F.XuC. L.WuD. H.WeiB. Q. 2003 Competitive adsorption of Pb2+, Cu2+ and Cd2+ ions from aqueous solutions by multiwalled carbon nanotubes, Carbon 412787 .
  31. 31. LiY. H.WangS. G.WeiJ. Q.ZhangX. F.XuC. L.LuanZ. K.WuD. H.WeiB. Q. 2002 Lead adsorption on carbon nanotubes, Chem. Phys. Lett. 357263 .
  32. 32. LiuX.HuberT. A.KopacM. C.PickupP. G. 2009 Ru oxide/carbon nanotube composites for supercapacitors prepared by spontaneous reduction of Ru(VI) and Ru(VII), Electrochimica Acta 54 2009 71417147
  33. 33. LuC.ChiuH. 2008 Chemical modification of multiwalled carbon nanotubes for sorption of Zn2+ from aqueous solution, Chem. Eng. J. 139 2008 462468 .
  34. 34. LupoF.KamalakaranR.ScheuC.GrobertN.RuhleM. 2004 Microstructural investigations on zirconium oxide-carbon nanotube composites synthesized by hydrothermal crystallization, Carbon 42 2004 19951999
  35. 35. MartinezM. T.CallejasM. A.BenitoA. M.CochetM.SeegerT.AnsonA.SchreiberJ.GordonC.MarhicC.ChauvetO.FierroJ. L. G.MaserW. K. 2003 Sensitivity of single wall carbon nanotubes to oxidative processing: structural modification, intercalation and functionalisation, MartinezM. T.CallejasM. A.BenitoA. M.CochetM.SeegerT.AnsonA.SchreiberJ.GordonC.MarhicC.ChauvetO.FierroJ. L. G.MaserW. K. (2003). Sensitivity of single wall carbon nanotubes to oxidative processing: structural modification, intercalation and functionalisation, Carbon . 41 22472256 .
  36. 36. MartinezC.CanleM. L.FernandezM. I.SantaballaJ. A.FariaJ. 2011 Kinetics and mechanism of aqueous degradation of carbamazepine by heterogeneous photocatalysis using nanocrystalline TiO2, ZnO and multi-walled carbon nanotubes- anatase composites, Applied Catalysis B: Environmental 102 563571
  37. 37. OkpalugoT. I. T.PapakonstantinouP.MurphyH.MclaughlinJ.BrownN. M. D. 2005 Oxidative functionalization of carbon nanotubes in atmospheric pressure filamentary dielectric barrier discharge (APDBD), OkpalugoT. I. T.PapakonstantinouP.MurphyH.MclaughlinJ.BrownN. M. D. (2005). Oxidative functionalization of carbon nanotubes in atmospheric pressure filamentary dielectric barrier discharge (APDBD), Carbon 43 29512959
  38. 38. OsorioA. G.SilveiraI. C. L.BuenoV. L.BergmannC. P. 2008 H2SO4/HNO3/HCl Functionalization and its effect on dispersion of carbon nanotubes in aqueous media, Applied Surface Science 2552485
  39. 39. OtvosZ.OnyestyákG.HanceA.KiricsiI.ReesL. V. C. 2006 Surface oxygen complexes as governors of neopentane sorption in multiwalled carbon nanotubes, Carbon 44 16651672 .
  40. 40. PengK.LiuL. Q.LiH.MeyerH.ZhangZ. 2011 Room temperature functionalization of carbon nanotubes using an ozone/water vapor mixture, Carbon 49 7076
  41. 41. PengX.LuanZ.Di Z.ZhangZ.ZhuC. 2005 Carbon nanotubes-iron oxides magnetic composites as adsorbent for removal of Pb(II) and Cu(II) from water, Carbon 43 855894
  42. 42. PietruszkaB.GregorioF. D.KellerN.KellerV. 2005 High-efficiency WO3/carbon nanotubes for olefin skeletal isomerization, Catalysis Today 102-103: 94-100
  43. 43. SalehT. A.GondalM. A.DrmoshQ. A. 2010 Preparation of a MWCNT/ZnO nanocomposite and its photocatalytic activity for the removal of cyanide from water using a laser, Nanotechnology 21 (49), 8: doi:10.1088/09574484 /21/49/495705
  44. 44. SalehT. A.GondalM. A.DrmoshQ. A.YamaniZ.H. A.L-yamaniA.A. 2011 Enhancement in photocatalytic activity for acetaldehyde removal by embedding ZnO nano particles on multiwall carbon nanotubes, Chemical Engineering Journal, 166(1), 407-412
  45. 45. ShaoD. D.RenX. M.HuJ.ChenY. X.WangX. K. 2010 Preconcentration of Pb2+ from aqueous solution using poly(acrylamide) and poly(N,N-dimethylacrylamide) grafted multi walled carbon nanotubes, Colloids Surf. A 360 7484 .
  46. 46. SmithB.WepasnickK.SchroteK. E.ChoH. H.BallW. P.HowardFairbrother. D. 2009 Influence of Surface Oxides on the Colloidal Stability of Multi-Walled Carbon Nanotubes: A Structure-Property Relationship, Langmuir 25 97679776
  47. 47. SubramanianV.WolfE.KamatP. V. 2004 Catalysis with TiO2/Gold Nanocomposites. Effect of Metal Particle Size on the Fermi Level Equilibration, J. AM. CHEM. SOC. 126 49434950
  48. 48. WangH.WangH.JiangW. 2009 Solar photocatalytic degradation of 2,6-dinitro-p-cresol (DNPC) using multi-walled carbon nanotubes (MWCNTs)-TiO2 composite photocatalysts, Chemosphere 75 11051111
  49. 49. WangS.ShiX.ShaoG.DuanX.YangX.WangX. 2008 Preparation, characterization and photocatalytic activity of multi-walled carbon nanotube-supported tungsten trioxide composites, Journal of Physics and Chemistry of Solids 69 23962400
  50. 50. WangS. G.GongW.LiuW.YaoY.GaoB.YueQ. 2007 Removal of lead(II) from aqueous solution by adsorption onto manganese oxide-coated carbon nanotubes, Separation and Purification Technology 58 1723
  51. 51. WoanK.PyrgiotakisG.SigmundW. 2009 Photocatalytic Carbon-Nanotube-TiO2 Composites, Adv. Mater. 21 22332239
  52. 52. XuY. J.ZhuangY.FuX. 2010 New Insight for Enhanced Photocatalytic Activity of TiO2 by Doping Carbon Nanotubes: ACase Study on Degradation of Benzene and Methyl Orange, J. Phys. Chem. C 114 26692676
  53. 53. YangQ.DengY.HuW. 2009 Preparation of alumina/carbon nanotubes composites by chemical precipitation, Ceramics International, 35 13051310
  54. 54. YuY.YuJ. C.YuJ. G.KwokY. C.CheY. K.ZhaoJ. C.DingL.GeW. K.WongP. K. 2005 Enhancement of photocatalytic activity of mesoporous TiO2 by using carbon nanotubes, Applied Catalysis A: General 289 186196
  55. 55. ZhangD.ShiL.FuH.FangJ. 2006 Ultrasonic-assisted preparation of carbon nanotube/cerium oxide composites, Carbon 44 28492867
  56. 56. ZhangH. B.LinG. D.ZhouZ. H.DongX.ChenT. 2002 Raman spectra of MWCNTs and MWCNT-based H2 adsorbing system, Carbon 40 24292436 .
  57. 57. ZhangS. C.FahrenholtzW. G.HilmasG. E.YadlowskyE. J. 2010 Pressureless sintering of carbon nanotube-Al2O3 composites, Journal of the European Ceramic Society 301373
  58. 58. ZhaoJ.WuT.WuK.OikawaK.HidakaH. .SerponeN. 1998 Photoassisted Degradation of DyePollutants. 3. Degradation of the Cationic Dye Rhodamine B in Aqueous Anionic Surfactant/TiO2 Dispersions under Visible Light Irradiation: Evidence for the Need of Substrate Adsorption on TiO2 Particles, Environ. Sci. Technol., 32 23942400
  59. 59. ZhenF.KunzaiJ. C.CuiF. S.XuY.KuangY. 2007 Preparation and capacitive properties of cobalt-nickel oxides/carbon nanotube composites, Electrochimica Acta 52 29592965
  60. 60. ZhouW.PanK.QuY.SunF.TianC.RenZ.TianG.FuH. 2010 Photodegradation of organic contamination in wastewaters by bonding TiO2/single-walled carbon nanotube composites with enhanced photocatalytic activity Chemosphere 81 555561

Written By

Vinod Gupta and Tawfik A. Saleh

Submitted: 25 October 2010 Published: 20 July 2011