Open access peer-reviewed chapter

Dynamic Behavior of Dust Particles in Plasmas

By Yoshifumi Saitou and Osamu Ishihara

Submitted: May 20th 2019Reviewed: July 24th 2019Published: May 22nd 2020

DOI: 10.5772/intechopen.88787

Downloaded: 89

Abstract

Experimentally observed dynamic behavior, such as a particle circulation under magnetic field, a bow shock formation in an upper stream of an obstacle, etc., will be reviewed. Dust particles confined in a cylindrical glass tube show a dynamic circulation when strong magnetic field is applied from the bottom of the tube using a permanent magnet. The circulation consists of two kinds of motions: one is a toroidal rotation around the tube axis, and the other is a poloidal rotation. Dust particles are blown upward from near the bottom of the tube against the gravity neighborhood of the tube axis. A two-dimensional supersonic flow of dust particles forms a bow shock in front of a needlelike-shaped obstacle when the flow crosses the obstacle. The slower flow passes the obstacle as a laminar flow. A streamline-shaped void where dust particles are not observed is formed around the obstacle.

Keywords

  • dust flow
  • dust fluid
  • bow shock
  • dynamic circulation
  • storm in a glass tube

1. Introduction

The natural world is filled with fluids. Fluids present various phenomena such as waves, oscillations, vortices, etc. Scales of such phenomena vary widely. The bow shock formed near the heliopause is in the astrophysical scale, while the Great Red Spot of Jupiter is in the planetary scale, a tornado is in the earth’s atmosphere scale, and a swirling tea in a teacup is in the tabletop scale.

It is often observed that collective behavior of individual particles can be regarded as a fluid. A complex plasma, defined as a plasma in which microparticles are embedded in the background of electrons, ions, and neutral particles, provides one of the examples of the case.

In 1986, Ikezi theoretically predicted existence of a crystalized structure with small particles contained in a plasma [1]. It was in 1994 that Hayashi et al., Thomas et al., and Chu et al. separately found in their experiments that charged dust particles formed the crystalized structure in plasmas [2, 3, 4]. Since then, research on dusty plasmas has been actively conducted [5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41]. Looking back on the past, Galilei discovered in 1610 that Saturn had “ears.” It was found later that the “ears” were a ring or rings by Huygens, Cassini, etc. [42]. Further later in 1856, Maxwell considered the stability of Saturn’s ring and concluded that the stable Saturn’s ring must consist of independent particles [43]. The interplanetary space is a plasma state dominantly filled by protons brought by the solar wind. Planetary rings like the Saturn’s ring is one of the examples that ubiquitously exist in the universe.

Research of complex plasmas including dust particles is unique in a sense that we can chase the motion of individual dust particles by the naked eye using the visible laser light on site without time delay.

In this chapter, experimentally observed dynamic behaviors, such as a circulation of dust particles under magnetic field and a bow shock formation in an upper stream of an obstacle, will be reviewed. A two-dimensional supersonic flow of dust particles forms a bow shock in front of a needlelike-shaped obstacle when the flow passes the obstacle. The slower flow passes the obstacle as a laminar flow. A streamline-shaped void where dust particles are absent is formed around the obstacle. On the other hand, dust particles confined in a cylindrical glass tube show a three-dimensional dynamic circulation when strong enough magnetic field is applied from the bottom of the tube. The circulation consists of two kinds of motions: one is a toroidal rotation around the tube axis, and the other is a poloidal rotation. Dust particles are blown upward from near the bottom of the tube against the gravity around the tube axis.

2. Bow shock formation in two-dimensional dust flow

A NASA’s Spitzer Space Telescope observed a shock structure formed in front of the speedster star known as Kappa Cassiopeia in 1994 [44]. The shock is formed near the boundary between a stellar wind and interstellar medium. Another example of a shock wave can be seen around a boundary between a planetary magnetosphere and a stellar wind. These shock waves are similar to a shock excited in front of a bow of a ship cruising fast a water surface and are called a bow shock.

The bow shock is also observable in a supersonic flow of charged dust particles in a complex plasma. In this section, we will look back our experimental work on the bow shock formation [45]. Charged dust particles levitate at height where the gravity and the sheath electrostatic force acting on each particle are balanced in an experimental device on the ground. Therefore, monosized dust particles distribute and flow in an almost two-dimensional plane. An obstacle is placed in the middle of the dust flow just like the star or the planet in the solar wind or the ship on the ocean. The obstacle is a thin needlelike conducting wire and forms a potential barrier against the dust flow. The bow shock is formed when the dust flow interacts with the potential barrier.

2.1 Experimental setup

The schematic of the experimental device Yokohama Complex Plasma Experiment (YCOPEX) is shown in Figure 1 [46]. Detailed description on the device and experimental setup can be seen in Ref. [45]. The device consists of a glass chamber and a flat metal plate. The size of the metal plate is 800 mm in length (xdirection = the main flow direction) and 120 mm in width (ydirection). The device is equipped with an up-and-down gate which is electrically controlled from outside. The up-and-down gate separates the plate into two regions: the reservoir of dust particles and the experimental region. A needlelike conducting wire is placed in the experimental region and is used as an obstacle. The potential of the obstacle is floating against the plasma potential here.

Figure 1.

Schematic drawings of the experimental glass chamber: a YCOPEX device (a) and a piezoelectric buzzer as the dust source (b).

The argon gas pressure is 3.6 Pa. To avoid the drag by neutral particles or by ions [45, 46, 47, 48, 49], the vacuum pump and the gas feeding are stopped when the pressure reached the set value. Plasma is generated with an rf discharge of 5 W (13.56 MHz). The measured plasma parameters are ne5×1014m3, Te5eV. The plasma potential is 30V.

Each dust particle is an Au-coated silica sphere of a=5μmin diameter and md=1.68×1013kgin mass. The particles are charged to Q=Zde=4.4±0.5×104e, where eis the elementary electric charge [49]. The particles levitate near the boundary between the plasma and the sheath, whose height is approximately 8 mm above the metal plate. The dust particles are irradiated with two thin fan laser lights from the radial directions. Mie-scattered laser light from the particles is observed and recorded with a camera placed outside the device.

In the initial state, the dust particles are accumulated in a cylindrical piezoelectric buzzer which is placed under the metal plate and acts as a dust source. A part of the accumulated dust particles is hopped into the plasma by energizing the buzzer. The dust particles are stored in the reservoir region above the metal plate when the up-and-down gate is in condition to the up position. By tilting the entire device at angle θand lowering the gate, the stocked dust particles begin moving and form the almost two-dimensional flow. The flow velocity is controlled by changing angle θ. The velocity reaches a terminal velocity before the particles arrive near the obstacle.

2.2 Wave modes observed in a complex plasma

It is known that there are extremely low-frequency longitudinal wave modes in complex plasmas. Typically, one is the dust acoustic (DA) mode, and the other is the dust lattice (DL) mode. The n-dimensional DA wave velocity, CDAnD, and the DL velocity, CDL, are given by

Cd=uZdmdfκ,E1

where Cd=CDAnDorCDL, and

uZdmd=Zd2e2ε0mdλDiE2

with ε0the permittivity of free space, λDi, the ion Debye length. The function fκis given by

fκ=1κ3/2forCDA3D12πκ2forCDA2D4πκκ2+2κ+2expκforCDLκ1E3

where κ=d/λDiwith das the interparticle distance [16, 19, 20]. The distance is given by

d=1nd3D1/3for3Ddust distribution1πnd2Dfor2Ddust distribution,E4

where nd3Dand nd2Dare three- and two-dimensional dust densities, respectively.

The velocity of a wave excited in the dusty plasma, Cd, is measured using the time-of-flight method at θ=0degree. The velocity of dust acoustic modes coincides well with the velocity of the dust lattice mode around κ=36. The three-dimensional dust acoustic mode with velocity CDA3Dis likely the candidate for the observed mode of the wave although the strict mode identification is still to be determined.

2.3 Bow shock formation

The particles flow from the reservoir region to the obstacle by changing the tilting angle θ. The void which has a streamline-like shape can be seen in the hatched area of Figure 2. The void is an area where dust particles are absent. The dust flow near the leading edge of the void is decelerated. The trajectories of dust particles are deflected toward the ±ydirection in front of the void.

Figure 2.

Typical example of the formed bow shock. Modified from Figure 3(b) of Ref. [45].

The flow velocity, vf, in the upstream area has a constant value which is mainly determined by a balance of the gravitational force controlled by angle θand the neutral drag force. The flow is almost uniform, and there is no prominent structure in the upstream area when vfis small. When vfincreases, an arcuate structure where the intensity of the scattered laser light is enhanced is formed in front of the leading edge of the void. For further increase of vf, a curvature of the arc becomes larger. The tail of the void is extended with increasing values of vf.

The arcuate structure is the bow shock. The value of vfis required to exceed Mach number 1 when the bow shock is formed, where the Mach number is defined as the ratio of the flow velocity to the dust acoustic velocity. The experimentally measured velocity is 71m/sMach numberM=1. It is found that the arcuate structure is distinctive when the flow is supersonic. In addition, there exists a deceleration region between the leading edge of the arcuate structure and the void as shown in Figure 2, that is, there is a region where the flow velocity is reduced in order to keep the flux constant around the obstacle. The presence of such a deceleration region, a subsonic flow region, between the wave front and the stagnation point is one of the defining features of the bow shock [50].

The density ratio ndp/nd0is shown as a function of the Mach number, where ndpis the density in front of the stagnation point and nd0is the density of the upstream area. It is known that a polytropic hydrodynamic model provides criterion for the shock wave formation [50]:

ndpnd0=1+γ12M21/γ1M<1γ+12γ+1/γ1M21+γ12M2γγ12M21/γ1M1E5

where γis the polytropic index.

2.4 Bow shock by a simulation

A molecular-dynamics simulation code is carried out to examine the bow shock formation. The density ratio ndp/nd0and its spatial distribution are calculated. The simulation result on the density ratio corresponds to the numerical result of Eq. (5) with γ=2.2. The experimental result on the density ratio seems to correspond to the case of γ=5/3(= the specific heat ratio of monoatomic gas) 2.2though there is a small deviation.

The polytropic index found in the simulation and experimental observation may result from the fact that the significant amount of internal energy of the polytropic fluid, which consists of charged dust particles, may be stored in the background plasma. The value of the complex plasma polytropic index indicates that the present complex plasma is far from isothermal (γ=1).

As for the spatial density distribution, the density contour plot shows the arcuate structure, and its curvature increases with increasing Mach number as seen in the experiment.

2.5 Bow shock formation in two-dimensional flow

Under the polytropic process which is a quasi-static process, p/nγ=const.and T/nγ1=const., are held with the polytropic index γ, where pis the pressure, Tis the temperature, and nis the density. The polytropic index means

γ=0isobaric process1isothermal processκhisentropic processisochoric processE6

where κhis the ratio of specific heat. The experimentally obtained polytropic index lies between 5/3and 2.2. The value 5/3is equivalent to the ratio of specific heat of ideal monoatomic gas. The bow shock forms under the almost adiabatic process. The value around 2 is suggested for the investigation on the solar wind [51, 52]. In addition, the dust flow consists of a collection of dust particles with finite size. It is hard to regard the fluid component as ideal. Hence, the polytropic index deviates from 5/3.

The bow shock formation is a nonisothermal process. The pressure ratio and the temperature ratio pdp/pd0and Tdp/Td0dependence on the density ratio ndp/nd0are given by pdp/pd0=ndp/nd0γand Tdp/Td0=ndp/nd0γ1, where pdpand Tdpare the pressure and temperature at the stagnation point and pd0and Td0are those at the upstream area, respectively. The results are shown in Figure 3. The bow shock is formed for ndp/nd0>1. These results suggest that the polytropic index may be determined by measuring the pressure ratio pdp/pd0or the temperature ratio Tdp/Td0.

Figure 3.

Expected changes in the ratios of the pressure and the temperature by the bow shock formation ndp/nd0>1 under the polytropic process.

In this polytropic process, there is a small amount of heat exchange with the outside of the system. The first law of thermodynamics gives

dQ=dU+pdV=CVdT+pdV,E7

where dQis a differential heat added to the system, dUis the differential internal energy of the system, and CVis the specific heat at constant volume. By integrating this equation from state 0 to state 1

Q01=CγT1T0,E8

where Cγ=CVγκ/γ1>0is the polytropic specific heat. As seen in Figure 3, T1T0=TdpTd0>0, and as a result, Q01>0. It is expected that the heat Q01is added to the system for the bow shock formation.

3. Dynamic circulation under magnetic field

You may watch a dynamic motion of tea leaves, set on the bottom of the teacup, by stirring the tea by a teaspoon. The tea leaves get close to the center and rise near the tea surface as illustrated in Figure 4. We can see a similar phenomenon in a complex plasma system. In this section, we will look back our experimental work on such a dynamic motion of dust particles in a complex plasma [53].

Figure 4.

Schematic of tea leaves in tea stirred in a teacup.

The observation of particle motion in the dynamic circulation similar to the motion of the tea leaves helps to understand the simple but profound nature of the ubiquitous vortex commonly encountered in nature.

3.1 Experimental setup

The experiment is performed in a cylindrical glass tube as shown in Figure 5. Detailed explanation on the experimental setup is given in Ref. [53]. The cylindrical coordinates rθzare with the origin at the inner bottom of the tube, and the gravity is in the negative zdirection.

Figure 5.

Schematic drawing of the experimental glass tube (a) and the coordinate system (b). The structure of the dust cloud can be seen in Figures 7 and 8.

The argon gas pressure is p=525Pa. A geometry of the gas supply and exhaust system is configured to avoid the neutral drag force acting on the dust particles in the experimental region. The plasma is produced by an rf discharge of 20 W (13.56 MHz). The electron density is 1014m3, the electron temperature is 3eV, and the ion temperature is estimated to be 0.03eV.

A magnetic field is applied by a cylindrical permanent magnet of 50 mm in diameter placed at a distance hbelow the powered electrode, and the magnetic field strength is controlled by adjusting the distance hby a jack. The strength of the magnetic field at r=0is given by

Bhz0.2950z+h+503T,E9

where hand zare measured in mm. The calculated Bhzis shown in Figure 6.

Figure 6.

Strength of the magnetic field at r=0.

Dust particles which are acrylic resin spheres of a=3μmin diameter and md=1.7×1014kgin mass are supplied from a dust reservoir on the top of the glass tube. Each dust particle is charged in the plasma to Q104e[49]. The particles in the experimental region are irradiated with a thin fan laser light from the radial directions. The laser sheet can be rotated around the laser axis. The scattered laser light from the particles is observed and recorded with a camera placed outside of the tube.

3.2 Behavior of dust particles in a glass cylinder

Because of the cylindrical symmetry of the glass tube, the motion of dust particles is well observable by watching in a meridional (vertical) plane as shown in Figures 5,7, and 8.

Figure 7.

Typical example of the formed structure. B=1.5kG. Modified from Figure 2(c) of Ref. [53]).

Figure 8.

Schematic of dust particle motion in the meridional plane. The arrows indicate the directions of dust particle motion.

When Bh137z=00.006T, the dust particles levitate a few mm above the glass bottom forming a thin disk of radius 20 mm with a dense group of particles at the rim of the disk near the outer wall. When Bis increased, the stored dust particles near the wall moved inward to the center and formed a disk of uniformly distributed at z>0. For B170=0.12Twith p=20Pa, where the electrons and ions are weakly magnetized and dust particles are rotating around the axis of the tube. The radial electric field is induced by the ambipolar diffusion and the vertically applied Bfield produces E×Bdrift motion of plasma particles, resulting in a solid body-like azimuthal motion of dust particles with angular velocity 1020mm/s.

With a further increase of Band reached B1200.15T, the dust disk becomes the form as shown in Figure 7, i.e., the disk is thicker and its radius is smaller. A meridional plane reveals a spectacular movement of dust particles in the thick disk.

Typical trajectories of the spectacular particle motions are shown with arrows in Figure 8. There are two small poloidal rotations in the meridional plane near the edges within the thick disk, i.e., one is the clockwise rotation on the right-hand plane, and the other is the counterclockwise rotation on the left-hand plane. The particle motion in the disk as seen in a meridional plane is somewhat similar to the motion of tea leaves as shown in Figure 4.

The dust particles move upward against the gravity near r=0. Especially, a part of the particles blows up and exceeds the disk thickness. Such ascending motion of dust particles is followed by radial movement toward the outer wall and then downward. The situation that the particles gush near the top looks like fireworks. After hitting close to the tube bottom, dust particles move inward along the tube bottom. At the same time, dust particles localized near the outer edge of the disk, which do not readily approach r0, form a local circulation in the meridional plane. While dust particles move in these closed circles in a meridional plane, the dust cloud rotates around the zaxis and forms a toroidal rotation. As a result, dust particles form a helical motion around the zaxis. A schematic illustration of the observed movement of dust particles is something similar as shown in Figure 4. In addition, there is a stagnation area around r0near the tube bottom, where a group of dust particles is not involved in the dynamic meridional rotation as shown in Figures 4 and 5.

3.3 MHD dust flow as a rotating fluid

The radial ambipolar diffusion is suppressed due to the electron magnetization, and the current starts to flow in an azimuthal direction in a magnetized plasma. The azimuthal electric field associated with the current density is given by

Eθ=1ωceτenκTee1nenerE10

In the present case, Eθ9V/mbecause ωceτen17, κTe/e3eV, and ne/ner12×102m, where ωceis the electron cyclotron angular frequency, τenis the mean-free-time of the electron-neutral collision, and κis the Boltzmann constant. This electric field will produce the azimuthal motion of ions with angular velocity vθ,ion=eEθ/miνin40m/s. Those ions circling around the tube axis will move dust particles resulting in a dust flow around the axis. Our observed maximum dust angular velocity is vθ,dust0.02m/s, near the wall.

The rotating magnetohydrodynamics (MHD) fluid involving dust particles may be described by the Navier-Stokes equation with the continuity equation of an incompressible fluid of constant mass density:

t+v·v=1mdndp+ν2v+1mdndJ×B+f,E11
·v=0,E12

where νis a kinematic viscosity of the dust fluid and f=fg+fd+fT+is an external force. The gravitational force fgis in the negative zdirection, while the drag forces fdby neutral particles, and ions are in the azimuthal direction. The thermophoretic force fTand the other external forces are negligible in our experimental conditions [54].

We consider rotating fluid with constant angular frequency Ωfar from the tube bottom z=0. Eqs. (11) and (12) can be solved for steady, axisymmetric flow with v=vrvθvzin cylindrical coordinates with boundary conditions vθ=, vr=0at z=, and vr=vθ=vz=0at z=0. We assume J=0Jθ0and B=00B. The equilibrium condition requires

rΩ2=1mdnd∂p∂rJθB,E13

indicating that the centrifugal force on a dust particle is balanced by the pressure gradient and the Lorentz force.

By introducing dimensionless parameters, v¯r=vr/, v¯θ=vθ/, v¯z=vz/νΩ, p¯=p/ρνΩ, and g¯=g/νΩ3with z¯=z/ν/Ω. Eqs. (11) and (12) can be expressed by a set of three ordinary differential equations:

d2v¯rdz¯2=1+v¯r2v¯θ2+v¯zdv¯rdz¯d2v¯θdz¯2=2v¯rv¯θ+dv¯θdz¯v¯zdv¯zdz¯=2v¯r,E14

supplemented by the pressure gradient equation:

dp¯dz¯=d2v¯zdz¯2v¯zdv¯zdz¯g¯.E15

The set of equations is well studied as similarity solutions for the rotating fluid [55, 56]. The solution shows the presence of a stagnation point at rz=00and the presence of a thin boundary layer near the bottom where the fluid moves inward. Our observation shows the boundary layer 3ν/Ω5mm.

As Eqs. (11) and (12) show, dust particles drift in the azimuthal direction, and the centrifugal force on a particle is given by fC=mdrαΩ2with α, a constant less than unity. The centrifugal force is balanced by an inward drag force by neutral particles fdn=CDπa2mnnnvr2/8, where CDis a drag coefficient, mnis a neutral mass, nnis a neutral density, and vr=βrΩis a representative radial velocity of dust particles with a constant β<1. The balancing equation gives the equilibrium radius as

r=83CDmdndmnnnαβ2a2.E16

Eq. (16) with α/β0.03gives an equilibrium radius of about 0.02 m, which agrees well with our experimental observation.

3.4 Storm in a glass tube

The mechanism of the meridional dust flow is understood in the following way. Initially dust particles are driven by the ion azimuthal motion caused by the radial plasma density gradient in the presence of a strong vertical magnetic field. While the MHD dust fluid forms a rotation around the tube axis, the angular velocity of dust particles near the tube bottom is reduced by the friction from the sheath plasma transition area. The friction reduces the centrifugal force. As a result, the pressure gradient force together with the Lorentz force which remains the same near the bottom generates a radial inward flow of dust particles. Because of the continuity, the radial inward motion will be compensated by an axial upward flow. Dust particles near the bottom ascend along the tube axis, where the sheath electric force pushes charged dust particles upward. When rising dust particles move outside of the sheath, the dust particles feel only the gravitational force. The ascending motion of dust particles near the axis is followed by the outward movement, and then the particles descend.

A circulation with an inward flow at the bottom has been known as a teacup phenomenon [57], also known as Einstein’s tea leaves [58]. In 1926, Einstein explained that tea leaves gather in the center of the teacup when the tea is stirred as a result of a secondary, rim-to-center circulation caused by the fluid rubbing against the bottom of the cup. It is indeed observed in our complex plasma experiment that there were some levitated dust particles staying close to the bottom near the center.

4. Discussion: collective behavior of dust particles as a fluid

A complex plasma is a system consisting of electrons, ions, neutral gas particles, and dust particles. The dust particles are macroparticles of nanometers to micrometers in size. In our experiments, monodisperse dust particles of 3 or 5 or 5.6 μm in diameter were used. Behavior of dust particles can be regarded as MHD fluid if lmfpL, τpτd, and the system keeps quasi-neutrality. Here lmfpis the mean free path of dust particles, Lis a representative scale length of a phenomenon, τpis time scale of the evolution of the phenomenon, and τdis the dust plasma period [59]. The quasi-neutrality is always kept. Typically, lmfp0.1 mm, L1cm, τp1s, and τd0.1sin our experiments. Hence, the dust cloud can be treated as an MHD fluid.

In water or air or other fluids, a tracer such as aluminum powder or smoke is often used for visualizing a motion of fluid elements. The tea leaves in a teacup are, of course, one of the examples of the tracer as well. This is an indirect observation of the motion because a different tracer has unique characteristics, e.g., a size or a specific weight. The uniqueness comes down to a variation in trackability of the tracer to the fluid element and affects the observation results. The various trackability may give a different result in a measurement. Schlieren imaging and shadowgraph are often used to visualize a flow, too. These methods observe a fluctuation of a density or a refractive index. The setting of the optical system, etc. requires high precision for these methods.

In contrast, in the dust fluid, it is possible to regard each dust particle as a fluid element itself. The particle can be visualized by illuminating using a visible laser light in experiments. The laser light suffers Mie scattering because the size of the dust particle (10μm) is usually larger than the wavelength of the visible laser light (several hundredsnm). The motion of the fluid element is directly visualized without being bothered about both the trackability and the optical precision. It is worth emphasizing that the visualization is achieved on the spot without time lag in experiment.

One of the applications of such a dust fluid is the new method to estimate the dust charge [60]. A dust particle has an electric charge Qin a plasma and levitates at a height where the electrostatic force due to the sheath electric field Eand the gravitational force fgare balancing, QE=fg, on the ground. In experiments to measure the charge of an individual dust particle, it has been hard to separate Qand Eindependently. In addition, the conventional measurement methods require to change the experimental setup to measure Qand E. However, by regarding the collection of dust particles as a fluid, it is possible to measure the resonant frequency of the dust fluid, i.e., the dust plasma frequency by externally applying the sinusoidal oscillation. The dust charge QAis calculated from the resonant frequency. The charge QAis an averaged charge for all dust particles present in the experimental region in this case.

In fluid dynamics, the Reynolds number is one of the important parameters. The Reynolds number is given by inertial forces/viscous forces. The Reynolds number is also important in the dust flow. There are investigations relating to the widely changed Reynolds number or the viscosity of dust fluid by the simulation methods [61, 62]. However, it is hard to observe turbulence in our experiments on the dust flow, i.e., it is expected that the Reynolds number is rather small even when M>1.

It is clear that collective behavior of dust particles can be described as a fluid globally. The fluid picture is held where the MHD conditions are satisfied. Intrinsically, however, the dust fluid is a group consisting of independent particles. Therefore, it is expected that the complex plasma includes unique features that is peculiar to a particle system, i.e., properties that are insufficient and difficult to be described by the MHD equation or the Navier–Stokes equation. Such a situation is possible where the MHD conditions do not hold locally. In fact, a few irregular particles are observed in quite rare case. For example, there is a dust particle whose orbit is irregular and different from the others in the way like the dust particle is reflected in a larger angle with faster speed by the obstacle in the bow shock experiment.

In addition, the following experiment may give another example. The schematic of the experimental device is shown in Figure 9(a) [63]. The dust cloud exists under an influence of an axisymmetric nonuniform magnetic field applied by a small permanent magnet. The dust particles frequently collide with other particles surrounding it. Only the dust particles locate quite near the inner edge and the outer edge rotating along the edges as shown in Figure 9(b). Excluding these edge regions, the collective motion of dust particles seems to be like a fluid. As described in the previous paragraph, the dust fluid has high viscosity. In that case, the rotating particles at the edges have to transfer their momenta to the neighboring particles and must drag the neighbors to their rotating directions. However, in the experiment, the particles do not drag their neighboring particles. It is considered that, at both edges, the dust particles behave as individual particles. Hence, the MHD conditions may be locally broken near the edges, and the particle motion there may suggest one of the particulate-like properties.

Figure 9.

Schematic of the experimental device (a) and the enhanced illustration of the dust cloud (b). The arrows in (b) are the directions that the particles at the edges rotate. The magnetic field is vertically upward.

5. Summary and subsequent development

It is found in our experiments that the group of dust particles collectively behaves in a similar way to a fluid. In the fast flow of M>1, the bow shock is formed in front of the obstacle. Under the strong magnetic field applied with the permanent magnet, the dust fluid shows a dynamic circulation.

In addition, there is the experimental result which may suggest a particle property of the group of dust particles. It is expected that the dusty plasma or the complex plasma bridges the different nature between continuum mechanics such as fluids and kinetics of particles.

Our results have inspired other researchers in wider fields beyond plasma physics [64, 65, 66, 67, 68, 69, 70, 71, 72, 73, 74, 75, 76]. The followings are examples. Tiwari et al. constructed two-dimensional generalized hydrodynamic model and discussed on turbulence in a strongly coupled plasma [64]. They reported that the turbulence was able to occur at a low Reynolds number if the Weissenberg number was high. Kähler et al. derived the ion susceptibility in a partially ionized plasma [65]. Tadsen et al. reported that the dust cloud confined in a magnetized plasma was diamagnetic [66]. Gibson et al. gave an improved understanding of magnetized electron behavior in a dipole magnetic field [67]. Laishram et al. investigated the dust vortex formation in a plasma [68].

Research on dusty plasmas has a strong influence to various areas of physics as seen above. Further progress will be expected.

Acknowledgments

We thank Prof. T. Kamimura and Prof. Y. Nakamura for their collaboration on the bow shock research. The work on the bow shock formation is supported by the Asian Office of Aerospace Research and Development under Grant No. AOARD 104158 and JSPS Grants-in-Aid for Scientific Research (A) under Grant No. 23244110. The work on the dynamic circulation is supported by the Asian Office of Aerospace Research and Development FA2386-12-1-4077 and JSPS Grants-in-Aid for Scientific Research (A) 23244110 and for Challenging Exploratory Research 24654188. One of the authors, Saitou, thanks Prof. Y. Hayashi for his support to the experiment using the small permanent magnet, and this work is partly supported by the Japan Society for the Promotion of Science (JSPS) Grant-in-Aid for Scientific Research (A) 24244094.

© 2020 The Author(s). Licensee IntechOpen. This chapter is distributed under the terms of the Creative Commons Attribution 3.0 License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

How to cite and reference

Link to this chapter Copy to clipboard

Cite this chapter Copy to clipboard

Yoshifumi Saitou and Osamu Ishihara (May 22nd 2020). Dynamic Behavior of Dust Particles in Plasmas, Progress in Fine Particle Plasmas, Tetsu Mieno, Yasuaki Hayashi and Kun Xue, IntechOpen, DOI: 10.5772/intechopen.88787. Available from:

chapter statistics

89total chapter downloads

More statistics for editors and authors

Login to your personal dashboard for more detailed statistics on your publications.

Access personal reporting

Related Content

This Book

Next chapter

Integral Photography Technique for Three-Dimensional Imaging of Dusty Plasmas

By Akio Sanpei

Related Book

First chapter

Retracted: Induction Plasma Synthesis of Nanomaterials

By Jiayin Guo

We are IntechOpen, the world's leading publisher of Open Access books. Built by scientists, for scientists. Our readership spans scientists, professors, researchers, librarians, and students, as well as business professionals. We share our knowledge and peer-reveiwed research papers with libraries, scientific and engineering societies, and also work with corporate R&D departments and government entities.

More About Us