Design specification of angular ring antenna.
Abstract
In this chapter, ultra wide band angular ring antenna has been proposed for wireless applications. It has been observed that antenna resonate from 2.9 to 13.1 GHz which has 10.2 GHz bandwidth. Further, it is observed that antenna has nearly omni-directional radiation pattern for E and H-plane at 3.5, 5.8, and 8.5 GHz. The theoretical analysis of the proposed has been done using circuit theory analysis. It was also found using simulation that antenna has good input and output response of 0.2 ns. Proposed antenna measured, simulated, and theoretical results matches for antenna characteristics, i.e., reflection coefficient and radiation pattern. Bandwidth of antenna lies between 2.9 and 13.1 GHz, so this antenna is suitable for Wi-Fi, Wi-Max, digital communication system (DCS), satellite communication, and 5G applications.
Keywords
- ultra wide band (UWB)
- angular ring
- finite ground plane
- microstrip line fed
- circuit theory
1. Introduction
Wireless communication systems are highly desired in various fields of security systems, Wi-Fi, Wi-Max, and mobile communication. These applications have special common devices, i.e., an antenna for efficient transmission and reception information. Presently, antennas are equipped in all communication devices and these devices are size and volume constrains. This leads to reduction of size for antenna in existing communication device. All communication devices have patch antennas for transmission and reception of signals. Scientists and researchers are investigating on these antennas since 1972 for reduction in size and increase in bandwidth. To achieve this, numbers of patch antenna designs and techniques were proposed. It was found by researchers that angular ring patch antenna is an efficient antenna which gives both size reduction and increased bandwidth.
Angular ring patch antenna was first reported in year 1985, by IJ Bahal for biomedical application. Thereafter, only few research have been reported on these antennas such as, theory and experiment on the annular-ring microstrip antenna, shared aperture microstrip patch antenna array for L and S-Bands, analysis of a gap-coupled stacked annular-ring microstrip antenna, compact stacked circularly polarized annular-ring microstrip antenna for GPS applications, annular-ring microstrip patch antenna with finite ground plane for ultra-wideband applications, compact concentric annular-ring patch antenna for triple-frequency operation, comparison of several novel annular-ring microstrip patch antennas for circular polarization, analysis of two-concentric annular-ring microstrip antenna, and broadband circularly polarized annular-ring microstrip antenna [1, 2, 3, 4, 5, 6, 7, 8, 9, 10]. All above reported papers has some limitations such as complicated geometry, lacks theoretical analysis for defected ground with microstrip line feed, circuit diagram at Radio frequency were not proposed for designed antenna and theoretical, simulated and experimental results were not compared.
In this chapter, ultra-wideband microstrip patch antenna is proposed for Wi-Fi, Wi-Max, DCS, and 5G applications. Partial ground plane with microstrip line fed techniques is used to achieve UWB band for various wireless applications. Detail descriptions of proposed antenna design are discussed in next section.
2. Geometrical consideration
The microstrip line fed angular ring patch antenna with rectangular ground is shown in Figure 1 and the antenna is fabricated on FR4 substrate and its top and bottom view is shown in Figure 2. The proposed antenna has been designed on FR4 substrate of height “h” and overall dimension of designed geometry is
FR-4 lossy, εr | 4.4 |
Radius of angular ring inner, | 3.5 mm |
Radius of angular ring outer, | 8.5 mm |
Circular path, | 5.0 mm |
Strip line length, | 5.0 mm |
Strip line width, | 3.5 mm |
Ground plane width, | 2.5 mm |
Ground plane length, | 12 mm |
Height of the substrate, | 1.57 mm |
3. Theoretical investigations
The resonating frequency of angular ring [11] is given as
where c is the velocity of light in free space,
The inner and outer radii of angular ring are given as
The angular ring patch antenna can be represented in circuit diagram as combination of inductance, capacitance and conductance, as shown in Figure 3. The values of inductance
where
Input impedance for the angular ring is given as,
Angular ring is connected to strip line; the strip line can be represented into RF circuit as combination of
The resonating frequency of the strip line is given as
The ground plane patch is represented as RF circuit combination of Resistance RG, inductance LGG, and capacitance CG. The RF circuit representation of the ground plane is shown in Figure 5, RG, CG, LGG can be calculated as [12, 13].
εe is the effective permittivity of the medium.
Further, there will be strong electromagnetic field between top patch (i.e., angular ring and strip line) and ground plane (rectangular patch). Due to which inductance and capacitance are developed between them and its RF circuit representation is shown in Figure 6. Thereafter, on excitation of antenna the impedance is also developed between top and bottom patch [12, 13, 14] and represented as,
The input impedance of strip line feed angular ring with defected ground plane and its RF circuit representation is shown in Figure 7 and is calculated using Eqs. (2)–(19)
Using Eq. (20) the input impedance of proposed has been used to calculate reflection coefficient (RC), return loss (RL) and voltage standing wave ratio (VSWR) can be calculated as,
where Z is the input impedance of the microstrip fed (
Using Eqs. (21)–(23) the theoretical plots for RL, VSWR, and RC with respect to frequency (GHz) can be plotted. In this chapter, theoretical plot for RC with respect to frequency (GHz) is plotted.
4. Result and discussion
The comparison between simulated [14], measured, and theoretical results is shown in Figure 8(a). It is observed from the figure that these three results are in approximately close with each other. Further, the bandwidth of theoretical, measured and simulated results is 10.63, 10.6, and 10.2 GHz, respectively. Bandwidth of antenna lies between 2.9 and 13.1 GHz, these bands are suitable for Wi-Max, Wi-Fi, digital communication system, satellite communication, and 5G applications. Measured result picture on Vector Network Analyzer (VNA) of proposed antenna is shown in Figure 8(b).
From Figure 9, it is observed that maximum input amplitude of the antenna is 1 sqrt W at 0.1 ns time interval, whereas maximum output amplitude is 0.34 sqrt W at a response time of 0.38 ns with phase reversal. The output response is not smooth because angular ring structure with rectangular ground plane.
Radiation pattern of the proposed antenna are shown in Figures 10 and 11 for E and H-plane, respectively. Figure 10(a) shows the radiation pattern measurement setup, proposed antenna under test is kept 200 cm apart from the horn antenna. Figure 10(b) and (c) are measured and simulated radiation pattern at 3.5 and 5.8 GHz, respectively. Measured and simulated radiation pattern are in close agreement in both cases and omni-directional patterns are observed. Figure 10(d) shows radiation pattern at center frequency. Major and minor lobes have been observed of same beam width for measured, theoretical, and simulated antenna at center frequency 8.5 GHz for H-plane. Figure 11(a)–(c) shows the radiation pattern for E-plane at 3.5, 5.8, and 8.5 GHz, respectively. Antenna shows nearly omni-directional radiation pattern at 3.5 and 5.8 GHz; whereas at 8.5 GHz, it is partially eight shaped. Electric field intensity is more toward 180° for E-plane and antenna 3 dB beam width is 87.4°. Slightly mismatch is observed in radiation pattern results because of partially open anechoic chambers and fabrication defects. It has omni-directional pattern so this antenna can be utilized for mobile communication.
Figures 12–14 show the surface current distribution of proposed antenna at center frequency for 90 and 0° phase, respectively. Further, from Figure 12, the maximum surface current of 86.4766 A/m is observed at the outer perimeter of angular ring near the edges of strip line and surface current is evenly distributed along length of antenna at 90° phase. Whereas, the surface current at 0° phase is not evenly distributed along the length of antenna and more surface current observed near feed as shown in Figure 13.
Figure 14 shows the gain and directivity of the antenna in dBi. It is observed that maximum gain of 2.75 dBi is achieved at 10.2 GHz; whereas, average gain of antenna is 2.1 dBi. Further, the directivity of the antenna at 10.2 GHz is maximum, i.e., 4.1 dBi and average directivity is 2.98 dBi.
The maximum radiation efficiency is achieved −1.5 dB (70.79%) at 10.2 GHz frequency as observed in Figure 15 and total radiation efficiency of proposed antenna at 10.2 GHz is found to be (−2.2 dB) 60.25%. This is because the loss occurs due to skin effect and conduction loss in antenna device.
5. Conclusion
From the above theoretical analysis, it is found that angular ring patch antenna can be utilized for UWB antenna. Further was observed that antenna cover frequency band between 2.9 and 13.1 GHz which has 125% bandwidth. From the results, it was also observed that antenna has good radiation characteristics and input and output response. Antenna has the gain and efficiency of 2.2 dBi and 70.79%. Simulated, measured, and theoretical results are matching for radiation pattern and reflection coefficient. Further, this antenna is suitable for digital communication system, satellite communication, and 5G applications.
Acknowledgments
The authors would like to thanks Nitte Education Trust for providing the research Grant No. Res/NMAMIT/03. We would like to thank Dr. K. Krishnamoorthy, Department of Electronics and Communications, National Institute of Technology, Surathkala, for providing measurement faculties of antenna in their research lab.
References
- 1.
Lee KF, Dahele JS. Theory and experiment on the annular-ring microstrip antenna. Annales des Telecommunications. 1985; 40 :508-515 - 2.
Dhiman J, Sharma A, Khah SK. Shared aperture microstrip patch antenna array for L and S-bands. Progress in Electromagnetics Research Letters. 2019; 86 :91-95 - 3.
Ansari JA, Ram RB, Singh P. Analysis of a gap-coupled stacked annular ring microstrip antenna. Progress in Electromagnetics Research B. 2008; 4 :147-158 - 4.
Ding K, Yu T-B, Zhang Q. A compact stacked circularly polarized annular-ring microstrip antenna for GPS applications. Progress in Electromagnetics Research Letters. 2013; 40 :171-179 - 5.
Rawat S, Sharma KK. Annular ring microstrip patch antenna with finite ground plane for ultra-wideband applications. International Journal of Microwave and Wireless Technologies. 2015; 7 (2):179-184 - 6.
Bao XL, Ammann MJ. Compact concentric annular-ring patch antenna for triple-frequency operation. Electronics Letters. 2006; 42 :1129-1130 - 7.
Bao XL, Ammann MJ. Comparison of several novel annular-ring microstrip patch antennas for circular polarization. Journal of Electromagnetic Waves and Applications. 2006; 20 :1427-1438 - 8.
Kanaujia BK, Vishvakarma BR. Analysis of two-concentric annular ring microstrip antenna. Microwave and Optical Technology Letters. 2003; 36 :104-108 - 9.
Guo Y-X, Bian L, Shi XQ. Broadband circularly polarized annular-ring microstrip antenna. IEEE Transactions on Antennas and Propagation. 2009; 57 :2474-2477 - 10.
Rasool N, Kama H, Basit MA, Abdullah M. A low profile high gain ultra lightweight circularly polarized annular ring slot antenna for airborne and airship applications. IEEE Access. 2019; 7 :155048-155056 - 11.
Kumar G, Ray KP. Broadband Microstrip Antenna. USA: Artech House; 2003 - 12.
Bahal IJ, Bartia P. Microstrip Patch Antenna. USA: Artech House; 1980 - 13.
Meada M. Analysis of gap in microstrip transmission line. IEEE Transactions on Antennas and Propagation. 1972; 32 :1375-1379 - 14.
Computer Simulation Technology (CST). Microwave Studio Suite Version. Germany: Dassault Systèmes and Darmstadt; 2018