Monopile is the most commonly used foundation type for offshore wind turbines. The local scour at a monopile foundation generated by the incoming shear flow has significant influence on both quasi-static lateral responses and dynamic responses of the monopile. This chapter focuses particularly on characterizing the local scour in both spatial and temporal scales and revealing the scour mechanisms associated with the flow field around a monopile. The predicting methods for the equilibrium scour depth and the time scale of scour are detailed under various representative flow conditions in the marine environment. The scale effect while extrapolating the results of model tests to prototype conditions is highlighted. The local scour imposes significant influence not only on the deformation and stiffness of the monopile foundation, but also on the natural frequency and fatigue life of the structure system. Monopiles with diameters up to 10 m have become a feasible option as the industry is currently advancing into deeper waters. More meticulous considerations for monopile design associated with the scour depth prediction and evaluation of scour effects are still in need to efficiently minimize the cost while remaining safety simultaneously.
- local scour
- combined waves and currents
- horseshoe vortex
- time scale
- scale effect
- pile-soil interaction
- natural frequency
Offshore wind power is developing into a major energy source globally due to the abundant reserves, high-energy density, and fewer civil complaints compared to onshore wind power. The global installed capacity reached more than 14,300 MW at the end of 2016 , and an increased potential for growth in future was estimated [2, 3]. To achieve high energy harvesting efficiency, the industry is currently advancing into deeper waters accompanied by upscaling the offshore wind turbines (OWTs) from 5 to 8 MW, 10 MW and then 12 MW  (see Figure 1). The steady upward trends in both water depth and size of OWTs have led to consequential growth in the loading, further aggravating the deformation of the foundations and potentially jeopardizing the operation of the OWTs.
As the most commonly adopted foundation for OWTs, the monopile had been used as the foundation of 2653 OWTs by the end of 2016, which accounts for over 80% , due to their ease of design and manufacture in contrast to other foundation types. A typical monopile is composed of a hollow steel cylinder with a diameter typically spanning 4 to 8 m and a slenderness ratio (driving depth over diameter) less than 10 . A special aspect to consider with monopile foundations for OWTs is that the vertical load mainly comprised of gravity load is relatively small compared with other offshore structures like oil and gas platforms. The horizontal loads generated by wind and wave actions, which are of similar magnitude to the gravity loads, are therefore of particular importance for the design . A typical laterally loaded offshore monopile foundation generally behaves rigidly due to their large bending stiffness and low slenderness ratio . The serviceability requirements including lateral deformation and stiffness rather than ultimate lateral resistance tend to govern design due to strict rotational tolerance specifications for monopile foundations .
Under the current and/or wave loadings, severe local scour can be generated around a monopile situated in cohesionless sediments. The maximum scour depth is generally predicted to be proportional to the pile diameter, and scour depths of over 1.5 times pile diameter were observed in many practical installations . Considering the lower slenderness ratio compared with more conventional offshore pile for oil and gas industries, the maximum scour depth at a monopile may account for over 25% of the driving length . This scour-induced driving length reduction has significant influence on both quasi-static lateral responses (e.g., ultimate lateral resistance and deformation stiffness) and dynamic responses (e.g. natural frequency) of monopile foundations. Therefore, proper assessments of local scour and its influence on structural responses are essential to the design of monopile foundation for OWTs.
In view of the complexity of local scour phenomenon around a monopile and scour effects on manifold monopile responses, this chapter aims to systematically summarize the predicting methods involving the maximum scour depth and the time scale under various flow conditions. The controlling mechanisms of local scour around a monopile are also revisited. Subsequently, we examine existing research on the effects of local scour on the responses of the monopile foundation.
2. Local scour around a monopile
2.1 General description and scour mechanisms
In the river hydraulics, the local scour at the bridge piers has been widely recognized to be one of the main causes for the structure failure . Hence, the phenomenon of scouring at bridge piers has ever been studied extensively over the past half century from various aspects, including local scour mechanisms associated with flow characteristics, prediction of the maximum scour depth, etc. Comprehensive descriptions of scour around a pile or bridge pier in steady currents have been given in Refs. [12, 13].
For a pile foundation installed in the marine environment, several phenomena with regard to the flow pattern would arise including a horseshoe vortex (HSV, or sometimes necklace vortex due to its shape) in front of the pile, wave vortices convected through the pile’s lee-side, and the contraction streamlines at the side edges of the pile. These changes induce an increased sediment transport capacity. If the scouring potential created by the large-scale eddy structures is strong enough to overcome the particles’ resistance to motion, local scour will be initiated around the pile (see Figure 2). As scour hole develops, the strength of the large-scale eddy structures will gradually be weakened, thereby reducing the transport rate from the local scour region. Equilibrium is reestablished if the sediment inflow of the scour hole is equal to the outflow for live-bed scour, or the shear stress caused by vortices is equal to the critical shear stress of incipient sediment motion at the bottom of the scour hole for clear-water scour. Two major issues concerning the local scouring process, namely the equilibrium scour depth and the time scale, usually need to be quantitatively characterized and are detailed in Sections 2.2 and 2.3, respectively. We herein focus on reexamining the general scouring mechanisms, which mainly involve characterization of the flow pattern under different incoming flow conditions.
A surface-mounted cylinder induces the boundary layer separation from the upstream bed in the incoming flow, resulting in a HSV system at the upstream junction corner of the cylinder. The existing test observations indicated that the HSV (including the down-flow) upstream of a cylinder is the most evident and significant contributor to the scour process in currents alone. Much work has been done for the HSV at a cylinder in steady currents. Many researchers investigated the HSV at a flatbed for the laminar case [14, 15, 16]. However, most of the practical HSVs occur with turbulent approach boundary layers . Baker  used smoke- and oil-flow visualization to observe the turbulent HSV system. The variation in the position of the primary horseshoe vortex with the flow parameters was presented graphically. Dargahi  tried to examine the coupling between the flow field and scouring around a circular pile. The consequences of an unsteady vortex pattern were indicated. With the development of the scour hole, the vortex rapidly grows in size and strength as additional fluid attains a downward component and the strength of the down flow increases (see ). This conclusion was also verified by the subsequent flow measurements [21, 22].
Kirkil et al.  investigated the influence of large-scale coherent structures and macroturbulence events on the scour hole development at a cylinder. The results indicated that the pressure fluctuations and turbulent kinetic energy levels inside the primary necklace vortex were much larger than those associated with the turbulence inside the boundary layer flow approaching the cylinder. Strong ejections and uplift events were observed in the region just behind the cylinder. Recently, the evolution of the HSV in a scour hole around a circular pile was studied by Guan et al.  using 2D Particle Image Velocimetry (PIV) technique. The results indicated that the horseshoe vortex system evolves from one initial small vortex to three vortices along the upstream slope of the developing scour hole. Both the strength and size of the main vortex increase with increasing scour hole size. Most existing studies regarding the HSV at a scour hole in steady currents mainly focus on describing the evolution of the HSV itself rather than revealing the time-dependent coupling between the HSV and the scour hole. There is still a great need to improve the understanding of this complex coupling process (see ).
In contrast to the substantial amount of accumulated knowledge for HSV in steady currents, relatively fewer studies (e.g., ) can be found regarding the flow patterns around a cylinder under waves, although the two-dimensional vortex flow behind a free cylinder subject to an oscillatory flow is well understood (e.g., ). Sumer et al.  concluded that the scour around a pile in waves is governed by the action of both lee-wake vortices and the horseshoe vortex. Their observations showed that the lee-wake vortices shed from the cylinder act like cyclones, sweeping the sediment grains into its core region and then lifting the grains upward via the updraft in the vortices. The extension and circulation of the lee-wake vortices are governed primarily by the Keulegan Carpenter (KC) number . The KC number is defined as
where U wm is the maximum velocity of the undisturbed wave-induced oscillatory flow at the sea bottom above the wave boundary layer, D is the pile diameter, and T is the wave period. In contrast to the controlling role of the lee-wake vortices in eroding the sediment grains around a cylinder, the HSV would be less significant because the wave boundary layer is usually thin (see [29, 30]), especially for relatively small KC numbers . Regarding monopile foundations for OWTs, the corresponding value of KC number is usually low due to the large diameter . Therefore, the effect of the HSV might be insignificant for the scour development around a monopile under waves.
In general, the controlling mechanism of the scour process around pile foundation in wave-alone or in current-alone condition has been well established. Yet for the condition of combined waves and currents, which is a common scenario in marine environments, the physical mechanism for the scouring phenomenon is less understood. When the waves and currents coexist, the sediment is normally picked up by the waves due to its higher capacity of lifting sands and transported by the currents due to its higher capacity of carrying sands. Nevertheless, the effect of waves and currents’ coexistence is more than just a superimposition of their capacities of initiating and carrying sediment, due to a nonlinear interaction between waves and currents within and outside the bottom boundary layer [32, 33, 34]. The only experimental investigation so far on the flow pattern around a vertical pile in a combined current-wave flow was made by Sumer et al. . Their results showed that introducing the following currents in the waves increases the size and lifespan of the horseshoe vortex and lowers the critical KC number for the threshold of horseshoe vortex. The horseshoe vortex exists for smaller KC with increasing the current-to-wave velocity ratio. This result is related to the increase in the adverse pressure gradient in front of the pile caused by the superimposed currents. For small values of KC (such as ), the presence of the horseshoe vortex is quite limited in both space and time domain, and its influence on the scour is much less than that in steady currents (). That is, with decreasing KC, the effect of horseshoe vortex decreases and that of the vortex shedding increases accordingly.
2.2 Equilibrium scour depth
The equilibrium scour depth prediction is a key concern in the geotechnical design for the coastal and offshore foundations. On the basis of laboratory flume tests and field data, many empirical equations have been proposed with respect to the equilibrium scour depth around a cylinder over the past few decades.
For the bridge scour in steady currents, Melville and Sutherland equation  and the Colorado State University (CSU) equation  are two of the most commonly used scour equations. They give somewhat conservative estimates of scour depth, the former perhaps more so than the latter . Other well-known scour equations were reviewed by Deng and Cai . The accuracy of several most commonly adopted scour equations were evaluated and compared by Johnson , Mueller  and Sheppard et al. , using a large set of field data.
Unlike the pier-scour in bridge waterways, the local scour at offshore monopile foundations should consider the action of waves. For scour depth around pile exposed to waves alone, the number of prediction equation is much fewer compared with that under steady currents. An empirical expression for scour depth at a circular slender pile exposed to regular waves was established :
where S is the equilibrium scour depth at the pile. Note that Eq. (2) is valid for the live-bed conditions. Sumer et al.  further investigated the effect of the soil density on the scour depth at a pile in waves. The scour depth was significantly increased when the bed soil was changed from medium dense sand to dense sand. Dey et al.  presented the results of equilibrium scour depths at circular piles in clay and sand-clay mixed beds under waves alone. The variation of equilibrium scour depth with KC for different soil conditions follows an exponential law, as was given in , having different coefficients and exponents. Recently, Zanke et al.  proposed the following unifying equation for the prediction of equilibrium scour depth around a pile under the action of waves, tidal or steady currents.
where x rel = x eff /(1 + x eff), x eff = 0.03(1 – 0.35U cr /U) (KC-6), U is the mean velocity in case of steady currents, and U cr is the critical velocity for initiation of sediment motion.
For shallow-water subsea locations, waves often coexist with currents, propagating either following or opposing the currents. This brings the soil response around marine structures more complicated than that due to waves or currents alone. Nevertheless, the related research is relatively few. Sumer and Fredsøe  conducted a series of tests of irregular waves propagating either along or perpendicular to the current, indicating that the scour depth for combined waves and currents is influenced by the KC number and the current-to-wave velocity ratio. The current-to-wave velocity ratio is defined as U cw = U c/(U c + U wm), in which U c represents the undisturbed near-bed current velocity component of the combined flow, and U wm is the maximum velocity of the undisturbed wave-induced oscillatory flow at the sea bottom above the wave boundary layer. Sumer and Fredsøe  carried out re-analyses of scour data in  and derived the following empirical expression for the scour depth under combined waves and current:
in which S c is the scour depth for the current-only case, and the parameters A and B are given as and B = 6exp(−4.7U cw ). The validity range of Eq. (4) is limited to 4 < KC < 25. The value of Sc /D can be expressed with a mean value Sc /D = 1.3 and a standard deviation σ S/D = 0.7. The maximum scour depth for the live-bed scour regime is suggested to take as Sc /D = 1.3 + σ S/D = 2.0 or Sc /D = 1.3 + 2σ S/D = 2.7 for design purpose. The large variation range of Sc/D in Eq. (4) could produce a great arbitrariness and uncertainty in the practical engineering application. Moreover, the accuracy of Eq. (4) is not very much optimistic . Rudolph and Bos  carried out model tests on scour around a monopile under combined waves and currents with oblique directions, focusing on the range 1 < KC < 10. They proposed an improved scour depth prediction formula based on Sumer and Fredsøe  by analyzing their new data and preceding data.
Recently, Qi and Gao [31, 48] conducted an experimental investigation of the local scour development under combined waves and currents at a monopile. The influence of the wave propagating direction relative to currents is obvious. The experimental results indicated that the wave-current interaction had a substantial effect on the time-development of local scour and the resulting equilibrium scour depth. An average-velocity-based Froude number (Fr a ) was proposed to correlate with the equilibrium scour depth (S/D) at offshore monopile foundation in combined waves and currents . The definition of Fr a is
in which U a () is the average water particle velocity during one-quarter cycle of oscillation under combined waves and currents, when the oscillatory motion and the currents are in the same direction; t is the time and g denotes the gravitational acceleration. The equilibrium scour depths (live-bed scour regime) under combined waves and currents obtained from the experiments were plotted as a function of Fr a (see Figure 3a), along with those of in [44, 49]. Following empirical expression for the correlation between S/D and Fr a was given for predicting equilibrium scour depth under live-bed conditions.
Eq. (6) indicates that the scour depth approaches its mathematical asymptotic value (S/D ≈ 2.0) as Fr a increases (e.g., larger than 1.0). Note that this asymptotic value is in the range of a typical scour depth prediction (S/D ≈ 1.7–2.4) by previous local scour equations around a pile for current-alone conditions. The prediction using the empirical correlation generally distributes in the range of 25% error lines (see Figure 3b), which is superior to the existing formula.
As aforementioned, most existing equations for predicting the equilibrium scour depth around a cylinder are based predominantly on scaled laboratory flume data. Therefore, the inherent scaling issue is worthy of clarifying before extrapolating the results of small scale scour experiments to prototype . The scale effect is essentially attributable to the use of three independent length scales in local scour experiments: cylinder diameter, sediment size, and water depth . The three length scales lead to several controlling similarity parameters that inevitably cannot be satisfied concurrently. Two aspects are specifically drawing attention involving the scale effect: one associated with inadequate similitude of large scale turbulence generated around a cylinder during scour tests and the other with the distortion of sediment size scaling.
The similitude of large scale turbulence requires preservation of flow patterns so that pressure heads along flow path scale directly with the geometric scale relating the small cylinder in a flume test to a prototype pile. The Froude number defined with incoming flow velocity and pile diameter is proved useful for reflecting the similitude associated with flow-field [51, 52]. It was concluded that the flume-based equations for predicting equilibrium scour depth at a cylinder may not adequately account for the similitude of large scale turbulence and thus commonly lead to over-conservative estimations in prototype applications .
Most flume experiments were forced to use particles of comparable size to full-scale particles due to requirements of both the similitude associated with particle mobility and the natural size limit to which bed particles become cohesive. As such, the similarity of sediment size with respect to pile diameter cannot be maintained. According to Melville and Chiew , D/d 50 barely has effect on the scour development for D/d 50 > 50, with d 50 as the median grain size of the sediment. However, some more recent research indicates a decrease in S/D at very large values of D/d 50 [54, 55]. Consequently, a prototype scour depth prediction based on the flume scour data is greater than that in the field, that is, a relatively conservative or safe prediction. A comparison between the maximum calculated scour data from different formulations used in standard and technical recommendations for the design of offshore wind farms and available scour data in European wind farms found in technical reports was once conducted by Matutano et al. . The observed maximum scour depths were largely less than estimated in most offshore wind farms studied, which is consistent with the similarity analysis.
It should be noted that various offshore standards like DNV·GL  recommend Eq. (2) proposed in  to estimate the scour depth around monopile foundations for the OWTs under combined waves and currents. This could be inappropriate and potentially lead to great inaccuracies .
2.3 Time scale
The time scale of scour process (T 0) is a certain amount of elapsed time for a substantial amount of scour to develop , which is essential for predicting the scour depth at any instant in a certain wave and/or current condition. In the case of live-bed scour, the equilibrium scour depth is achieved faster than the clear-water case, generating a smaller time scale. The time scale of scour process can be defined in several ways according to different mathematical functions for approximating the scour development toward the equilibrium stage . For example, Briaud et al.  proposed a hyperbolic function , where S e is the equilibrium scour depth. Alternatively, a more commonly used definition was proposed in : . The value of the time scale can be obtained by fitting the measured scour depth development curve with these functions of . The normalized time scale is usually defined as
where s is the specific gravity of sand grains.
For steady currents, the normalized time scale is associated with the ratio of boundary layer thickness to pile diameter () and the Shields parameter (), using following empirical expression for live-bed scour regime .
The Shields parameter (θ) is defined as
in which U f is the maximum value of the undisturbed friction velocity, is the sediment grain density, and is the water density. The detailed calculation procedure of θ is given by Soulsby .
In the case of waves, the time scale of the scour process around a cylinder is governed by two parameters, namely the KC number and the Shields parameter. The empirical expression of T* based on and for live-bed scour regime can be represented by .
Under combined waves and currents, Petersen et al.  concluded that the time scale of scour varies with the KC number, the Shields parameter associated with the wave component of the flow (), and U cw. The time scale of scour increases significantly when even a slight current is superimposing on a wave. On the basis of the data of Refs. [61, 62] and their own, Chen and Li  proposed a piecewise fitting formula for the time scale of scour under combined waves and currents (see Figure 4)
2.4 Backfilling process
Backfilling process is the deposition of sediment into a scour hole previously generated, when the pile is exposed to a changing flow environment (the flow environment changing from, e.g., a steady current to a wave, from a steady current to combined waves and currents, or from a wave to a smaller wave). For the monopile foundations of the OWTs, the flow climate changes continuously, hence leading to scour and backfilling in an alternating fashion. The backfilling process needs to be quantitatively estimated to establish models for predicting the time history of scour and backfilling for large periods of time (see ).
Hartvig et al.  experimentally studied the scour and backfilling around a pile subjected to alternating sequences of currents with and without superimposed irregular waves. The results indicated that initially current-scoured beds, when subjected to waves, are backfilled about 10 times slower than the scoured ones. Sumer et al.  later presented a systematic investigation of the scour holes backfilling under waves or combined waves and currents around a pile. The results showed that the scour depth corresponding to the equilibrium state of backfilling is the same as that corresponding to the equilibrium state of scour around the pile for the same wave or combined waves and currents climate. That is, the final equilibrium scour is uninfluenced by the loading history of the flow but only dependent on the flow condition at the last stage if the last loading stage is sufficiently long. The time scale of backfilling is much larger than that of scour when the KC number associated with the backfilling is KC < O(10) (typical wind farm application). Various empirical equations involving the time scale were further proposed for different flow environment changes.
Backfilling can reduce the scale of the scour hole, which is beneficial to the bearing behavior of a monopile unprotected against scour. Sørensen et al.  assessed the relative density of the backfilled soil around a model monopile of 0.55 m diameter based on the test in a large wave channel. The relative density of the backfill material was found to be rather large, varying between 65 and 80%. Note that these values were obtained from only one set of laboratory tests, and lower densities may exist. The backfilled soil was found to increase the soil support to a monopile foundation significantly. Therefore, an optimized design with respect to both the fatigue limit state and the ultimate limit state can be achieved by considering the time variation of the scour depth .
3. Effects of local scour on the lateral response of a monopile
3.1 Lateral bearing behavior
The lateral response of a pile is commonly evaluated using a load transfer approach, with “p-y” curves quantifying the nonlinear interaction between the pile and the surrounding soil. The p-y curves idealize the soil as a series of independent springs distributed along the pile length, with each spring describing the nonlinear relationship between the lateral soil resistance (p) and the lateral deflection of the pile (y). Various formulations for p-y curves have been developed for sands, for example Refs. [68, 69, 70, 71]. The results in Refs. [68, 69] form the basis of the widely used API method .
Scour around submarine structures leads to a reduction in the effective stresses and hence strength and stiffness of the soil at a given depth around a pile. As scour depth is predicted to scale with the pile diameter, scouring can impact greatly on the overall response of large-diameter monopiles due to the low slenderness ratio (typically between about 3 and 10). As shown in Figure 5, scour reduces the pile embedment depth from L to L’ and increases the load eccentricity (cantilever length) from e to e’, changing the profiles of lateral soil resistance p, inducing much larger deformations of the pile and reducing the foundations stiffness.
Scour can cause the p-y response at a given absolute depth z (measured from the original soil surface or “mudline”) to soften, reducing both initial stiffness and the limiting resistance. In design codes such as DNV·GL , local scour is often considered to cause complete loss of soil resistance down to the depth of scour below the original seabed while estimating the pile capacities. Although such a design practice is simple, it often leads to extreme conservative pile foundation design and subsequent unnecessary cost . In recent years, the importance of scour hole dimensions for pile capacities has been increasingly recognized.
In an analytical study , general scour effects were incorporated by updating the parameters per unit length (p ult) at a given depth to account for the over-consolidation induced by removal of a scour depth of sand. Lin et al.  and Yang et al.  further modified the ultimate lateral resistance due to changes in the shallow wedge-type failure mechanism to consider the effects of the local scour. Results indicated that the local scour hole would result in much higher lateral soil resistance for a given depth than for the general scour case, that is, complete removal of the soil surface layer. Tseng et al.  combined the approach of Sørensen  for modifying the initial modulus of subgrade reaction (k py) and the approach of Lin et al.  for modifying p ult to evaluate the scour effect on the deformation response of monopile foundations. According to the case analysis, when the p-y curve method suggested by the design guidelines for an offshore wind turbine was used to design the monopile foundation for an OWT, the foundation deformation was underestimated for a scour depth of less than pile diameter, and foundation stiffness was underestimated for a scour depth of greater than pile diameter.
A series of centrifuge tests were conducted by Qi et al.  to investigate the scour effects on p-y curves. A practical approach to incorporate effects of scour on the p-y curves was proposed by adopting an effective soil depth (z e) in the determination of p-y curves. The effective soil depth was expressed by
where the effective soil depth is a weighted-average of the soil depth relative to the original mudline z and the soil depth below the current scour base (, S is the scour depth), f is an empirical parameter indicating the transition rate for the effective soil depth from z e = z’ at the current mudline to as the soil depth increases. The recommended value of f = 1.5 for local-scour conditions was based on the tests with 30° slope angle of the scour hole. As the slope angle of the scour hole decreases, the effect of the sloping overburden soil above the level of the scour base reduces and the value of f should be reduced accordingly. This conclusion conforms to the results of a recent study by Lin and Wu .
Local scour not only exaggerates the deformation and reduces the stiffness of the monopile foundation, but also changes its bearing mechanism. Monopile foundations for the OWTs generally behave rigidly, rotating as a whole and developing a “toe-kick” phenomenon. Figure 6 illustrates the mobilized soil resistance components of a laterally loaded short pile. Significant base shear and axial resistance will be mobilized at the pile tip if the slenderness ratio gets sufficiently small. Moreover, vertical side resistances emerge around the pile shaft due to the mobilized horizontal displacement of the pile tip and rotation of the pile. Numerical investigations by Bekken  and Byrne et al.  have confirmed the significant contributions due to the horizontal pile tip displacement and rotation of the pile on the resistance of a monopile.
To investigate the scour effect on the behavior of a laterally loaded monopile, a three-dimensional finite element model was proposed and verified by Qi and Gao . The results indicated that the scour could induce a significant transition of pile behavior for a typical monopile foundation of the OWTs. Figure 7(a) shows the variation of y p/y n with E s L 4/E p I p, in which y n denotes the lateral pile displacement at the loading position obtained from the 3D finite element results, and y p denotes the lateral pile displacement according to the conventional p-y method. The non-dimensional expression of E s L 4/E p I p is aimed to reflect the rigidity of the pile foundation [7, 84], where I p denotes the second moment of area of a pile and E p I p represents the bending stiffness of the pile. It is seen that for an approximate range of E s L 4/E p I p > 50, the value of y p/y n is generally equal to 1.0, while the value of y p/y n obviously deviates from the value of y p/y n = 1.0 for E s L 4/E p I p < 50. The deviation of y p/y n implies that due to the scour-induced increase of pile rigidity (see Figure 7(b)), the pile’s tip and shaft resistance could become a significant component of the whole soil resistance. The parameter L s in Figure 7(b) denotes the pile embedment depth after scour. The traditional p-y approach only takes account of the lateral soil resistance and thus the scour would render the traditional p-y approach inapplicable for post-scour conditions.
There are relatively fewer studies concerning the scour effect on the pile behavior under cyclic loading compared with aforementioned studies on the monotonic pile behavior . Achmus et al.  numerically quantified the scour-induced increase of pile deformation by adopting a degradation stiffness model to account for cyclic loading. The results indicated an evident accumulation of lateral deformation under cyclic loading. Up to now, no systematic investigations into the influence of scour on the cyclic pile behavior can be found in the literatures. This issue needs to be further studied. Moreover, local scour and backfilling occurs around a monopile foundation in an alternating fashion due to the continuously changing flow climate in marine conditions. This variation of scour depth should also be included while evaluating the long-term cyclic pile behavior.
3.2 Natural frequency and fatigue life (FL)
Compared to other types of OWT foundations such as gravity base, tripod, and suction bucket, the monopile is a dynamically sensitive structure due to its flexibility. The primary excitation forces arise from the wind, waves, and the rotor excitations. The fundamental frequency f 0 (the first tower bending frequency) of the structure is the most important controlling parameter for its dynamic response.
The OWTs are usually designed as soft-stiff structures in order to avoid resonances, meaning that f 0 is above the rotational frequency of the rotor f 1P but below the blade-passing frequency f 3P (see Figure 8). The excitation frequencies related to environmental loads from wind and waves are typically below the 1P frequency for OWTs with relatively small installed capacities, for example, smaller than 3.6 MW [87, 88]. Nevertheless, for a 6–8 MW modern OWT on a monopile, designed for the soft-stiff frequency range, f 0 would be around 0.20–0.23 Hz . In this frequency range, the fundamental mode of the structure would resonate with the waves at low wind speeds and be exposed to high spectral energy of waves during higher wind speeds. Due to the narrow soft-stiff frequency range for the OWTs on monopile foundations, even a small natural frequency shift from the initial design value may finally lead to resonance and the resulting stress in the materials of the monopile will be higher than in the quasi-static case. This high stress would potentially reduce the FL of the OWTs significantly.
Scour around the monopile leads to significant reduction of f 0. This would make f 0 align with the frequency of the passing sea waves or the rotational frequency of the rotor (f 1p) under certain circumstances, exposing structures to the threat of resonances. Sørensen and Ibsen  calculated the undamped natural frequencies of an existing offshore wind farm at HornsRev1 by means of the Winkler model approach. The stiffness derived from p-y curves given in the API code was adopted in their desk study, without accounting for the degradation of stiffness due to cyclic loading. The results revealed that the first natural frequency decreases with approximately 5% when the scour depth reached 1.3D. Prendergast et al.  conducted finite element numerical modeling to examine the scour effects on the natural frequency of a 3.6 MW OWT on a monopile in typical offshore sand deposits. The numerical model was validated by scale model tests and proved capable of tracking the scour-induced change in the natural frequency of the system. A reduction of up to 8.5% in natural frequency was observed in loose sand for S/D = 1.3. A comparison among cases with different soil stiffness profiles suggests that scour-induced resonance of an OWT on a monopile is most likely to occur in loose deposits. Prendergast et al.  recently improved the numerical model to further include the effect of spatial variability in soil properties derived from measured Cone Penetration Test (CPT) data. A stochastic ground model was developed to account for the uncertainty in soil-structure interaction stiffness for a given offshore site. The results indicated that the first natural system frequency reduces while the range of predicted system frequencies increases as the scour progresses. This means that the results of frequency-based SHM (structural health monitoring) technique for assessing scour magnitude-based solely on first natural frequency measurements becomes less certain for a deeper scour hole.
Several recent studies have focused on the scour effects associated with the FL of OWTs. Damgaard et al.  performed fully coupled aero-hydro-elastic simulations to evaluate the scour effects on the fatigue loads for parked OWTs. It was shown that a scour hole of 1.3D deep increases the fatigue damage equivalent moment with approximately 40%. Note that time-varying stiffness/damping properties of the soil due to long-term cyclic loading [93, 94] and scour depth variation due to backfilling are not accounted for. Rezaei et al.  presented a study of scour and backfilling effects on the FL of a 5 MW monopile supported OWT, using quasi-static, modal, and time-domain fatigue analyses. It was demonstrated that a scour depth of 1.5D could result in a 45% reduction of the FL of the wind turbine structure. Backfilling is beneficial to extend FL of the OWTs. Nevertheless, the relative density barely has effect on the FL of the OWTs.
4. Concluding remarks
Monopile is the most commonly adopted foundation type for OWTs. Local scour induced by waves and/or currents can jeopardize the function of the structure system to a great extent. In contrast to bridge scour which has been sufficiently studied over the past half century, an important feature of scour phenomenon around an offshore monopile stems from the various flow conditions in a marine environment, namely waves only, currents only, and combined waves and currents. In view of the complexity of incoming flow conditions, several crucial aspects related to local scour around a monopile foundation are reviewed, including the fundamental scour mechanisms, the maximum scour depth, the time scale, and the backfilling process. The inherent scaling issue arising from extrapolating the results of small scale scour experiments to prototype is clarified.
The driving depth of an offshore monopile can be significantly reduced by the local scour due to the low slenderness ratio, consequently imposing great influence on twofold structural responses. First, scour will cause the p-y response at a given absolute depth to soften, reducing both initial stiffness and the limiting resistance. Moreover, scour would render the traditional p-y approach inapplicable for post-scour conditions due to the change of bearing mechanism. Second, scour around the monopile leads to significant reduction of the fundamental frequency. This would make the fundamental frequency align with the frequency of the passing sea waves or the rotational frequency of the rotor under certain circumstances, exposing structures to the threat of resonances.
The current upward trends in both water depth and size of OWTs have led to consequential growth mainly in the horizontal loading. Monopiles with diameters up to 10 m have been proposed as a feasible option to support the OWTs with approximately 10 MW installed capacity. To efficiently minimize the cost while remaining safety, more meticulous considerations for monopile design are in need involving the scour depth prediction and evaluation of scour effects on structural responses. An alternative hybrid foundation system comprising a monopile and a bearing plate (or skirted footing) has been demonstrated to enhance the lateral bearing capacity compared with a monopile [96, 97, 98, 99]. Nevertheless, the enhanced capacity of the hybrid foundation largely relies on the proper interaction between the bearing plate and the soils at the shallow zone of the seabed, where local scour and wave-induced pore pressure could occur [100, 101, 102, 103, 104, 105, 106, 107, 108]. The extent of local scour and scour effects on both the bearing capacity and natural frequency of a hybrid monopile need to be further investigated.
This work is financially supported by the National Natural Science Foundation of China (Grant Nos. 11602273; 11825205) and the Youth Innovation Promotion Association of the Chinese Academy of Sciences (Grant No. 2012014).