The detection and analysis of SF6 decomposition components are of great significance in online condition assessment and fault diagnosis of GIS. Considering the shortcomings of general detection methods, carbon nanotubes (CNTs) gas sensor was studied to detect the SF6 decomposition components because of its advantages in large surface activity and abundant pore structure, et al. The large surface area has a strong adsorption and desorption capacity. In this chapter, SF6 decomposed gases, namely SO2F2, SOF2, SO2, H2S and CF4 are chosen as probe gases because they are the main by-products in the decomposition of SF6 under partial density (PD). First, the properties and preparation methods of CNTs are introduced to verify the advantages of CNTs for SF6 decomposition components detection. Then, both theoretical calculation and sensing experiment were adopted to study the microadsorption mechanism and macrogas-sensing properties. Based on the intrinsic CNTs, study for SF6 decomposition components adsorption, Pd, Ni, Al, Pt and Au metal doping CNTs and plasma-modified CNTs are discussed in order to enhance the gas sensing and selectivity of CNTs.
Part of the book: Nanomaterials Based Gas Sensors for SF6 Decomposition Components Detection
Titanium dioxide nanotube arrays (TNTAs) are a typical three-dimensional nanomaterial. TNTA has rich chemical and physical properties and low manufacturing costs. Thus, TNTA has broad application prospects. In recent years, research has shown that because of its large specific surface area and nanosize effect, the TNTAs have an enormous potential for development compared with other nanostructure forms in fields such as light catalysis, sensor, and solar batteries. TNTAs have become the hotspot of international nanometer material research. The tiny gas sensor made from TNTA has several advantages, such as fast response, high sensitivity, and small size. Several scholars in this field have achieved significant progress. As a sensitive material, TNTA is used to test O2, NO2, H2, ethanol, and other gases. In this chapter, three SF6 decomposed gases, namely SO2, SOF2 and SO2F2, are chosen as probe gases because they are the main by-products in the decomposition of SF6 under PD. Then, the adsorption behaviors of these gases on different anatase (101) surfaces including intrinsic, Pt-doped and Au-doped, are studied using the first principles density functional theory (DFT) calculations. The simulation results can be used as supplement for gas-sensing experiments of TNTA gas sensors. This work is expected to add insights into the fundamental understanding of interactions between gases and TNTA surfaces for better sensor design.
Part of the book: Nanomaterials Based Gas Sensors for SF6 Decomposition Components Detection
Gas Insulated Switchgear (GIS) has been widely used in substations. The insulating medium used in GIS is sulfur hexafluoride (SF6) gas. However, the internal insulation defect existed in GIS would inevitably lead to partial discharge (PD), and cause the composition of SF6 to SOF2, SO2F2 and SO2 and other characteristic component gases. The decomposition phenomenon would greatly reduce the insulation performance of SF6 insulated equipment, and even paralyze the whole power supply system. In this chapter, we first discuss the objective existence, decomposition mechanism and harmness of insulation defects. Then the methods for insulation defects detection used to avoid the insulation accidents are introduced. Comparing all of the detection methods, diagnosing the insulation defect through analyzing the decomposed gases of SF6 by chemical gas sensors is the optimal method due to its advantages, such as high detection accuracy and stability, signifying the importance of developing chemical gas sensor used in SF6 insulated equipment. In conclusion, there kinds of gas sensor material, carbon nanotubes, graphene, are chosen as the gas sensing materials to build specific gas sensors for detecting each kind of SF6 decomposed gases, and then enhance the gas sensitivity and selectivity by material modification.
Part of the book: Nanomaterials Based Gas Sensors for SF6 Decomposition Components Detection
In order to judge the inside insulation fault of SF6 insulated equipment, the gas-sensing properties to a series of characteristic SF6 decomposition components, SOF2, SO2F2, SO2, H2S, CF4, HF, and SF6, have been studied. In this study, a comparative study of these gas-sensing materials has been made in theoretical and experimental fields to find the optimal gas-sensing material, and put forward the effective approaches to improve the gas-sensing properties of materials.
Part of the book: Nanomaterials Based Gas Sensors for SF6 Decomposition Components Detection
Graphene is an allotrope of carbon apart from graphite, diamond, fullerene and carbon nanotubes. Because graphene has unique mechanical, structural, thermal and electrochemical properties and can present the stability characteristics of these features, it becomes two‐dimensional (2‐d) materials which can alter three‐dimensional (3‐d) carbon nanotubes composite materials and has important research value. Pristine graphene and graphene films doped with Au nanoparticles were synthesized by the chemical reduction method. Their corresponding gas sensors were both fabricated by the traditional drop coating method and then used as an adsorbent for the detection of H2S, SO2, SOF2 and SO2F2 at room temperature. Theoretical simulation was also investigated when the decomposed gaseous components of sulfur hexafluoride (SF6), namely, H2S, SO2, SOF2 and SO2F2, were adsorbed on pristine and Au‐embedded graphene based on DFT. In order to interpret the adsorption processes between Au‐doped graphene and gas molecules, this chapter discussed the charge transfer mechanism on the adsorption surface for further investigation.
Part of the book: Nanomaterials Based Gas Sensors for SF6 Decomposition Components Detection