Numerical Investigations of Electromagnetic Oscillations and Turbulences in Hall Thrusters Using Two Fluid Approach

The first part of the contributed chapter discuss the overview of electric propulsion technology and its requirement in different space missions. The technical terms specific impulse and thrust are explained with their relation to exhaust velocity. The shortcoming of the Hall thrusters and its erosion problems of the channel walls are also conveyed. The second part of the chapter discuss the various waves and electromagnetic instabilities propagating in a Hall thruster magnetized plasma. The dispersion relation for the azimuthal growing waves is derived analytically with the help of magnetohydrodynamics theory. It is depicted that the growth rate of the instability increases with magnetic field, electron drift velocity and collisional frequency, whereas it is decreases with the initial drift of the ions.


Introduction
In the past few years, electric propulsion has received widespread attention as an alternative to chemical propulsion for spacecraft. A chemical thruster is capable of producing high thrust, but it provides a relatively low specific impulse. This limitation of chemical thrusters opens up discussion of the use of electric thrusters, which provide much higher specific impulses. A high specific impulse allows the spacecraft to reach the same speed with lower propellant consumption than chemical ones or travel faster with the same propellant mass [1][2][3][4][5][6][7][8][9][10]. In addition, the use of a high specific impulse, electric thruster permits a significant reduction in propellant mass on spacecraft, which helps reduce launching cost, extending mission lifetime or increase the payload mass on the spacecraft [2]. Therefore, the benefits that electric thrusters provide make them the best choice for in-space propulsion of spacecraft.
To date, several different types of electric propulsion thrusters have been developed, of which Hall thrusters are the most reliable and widely used. Hall thrusters are simple in design, consisting of an annular discharge channel, an anode, a cathode and a radial magnetic field across the channel [1]. A propellant, usually Xenon, is injected to channel through the hollow anode and a high potential difference is applied between the anode and cathode. The electrons emitted from the cathode and start moving towards the anode due to the potential difference. As they enter the discharge channel, they get trapped in the radial magnetic field generated by electromagnetic coils (or permanent magnets) and start drifting in the azimuthal direction (E x B). Due to this trapping, the residence time of electrons in the discharge channel increases and they move very slowly towards the anode. Electrons, then collide with neutral propellant atoms entering the discharge channel and ionize them. Then, these generated ions are accelerated to high velocity towards the thruster exhaust by the electric field to generate thrust. On the thruster exterior, the ion beam is neutralized by electrons from the virtual cathode so that no charge builds up on the spacecraft's surface [2]. More details on Hall thruster operation and fundamentals can be found in [1][2][3][4][5][6][7][8][9][10][11][12][13].
Hall thrusters offer several benefits like simple design, high thrust-to-power ratio, high efficiency, improved performance, etc., which give them a clear advantage over other electric thrusters. For an input power range of 0.1 kW-20 kW, they can produce a few mN to 1 N of thrust and offers a specific impulse in the range of 1000s-3000s with more than 50% efficiency [14]. Hall thrusters can also adjust their thrust level and specific impulse by varying the discharge voltage and propellant mass flow rate, which makes them suitable for applications such as precision maneuvering, attitude control, station keeping and orbital raising [15]. In addition, plasma in a Hall thruster remains quasi-neutral, which eliminates the issue of space charge, allowing the Hall thruster to achieve higher thrust densities. Because of all these characteristics, the space community has shown great interest in Hall thrusters and they have been used successfully on many spacecraft for space missions and maneuvers.
Thrust is caused by a change in a substance's momentum as a result of a chemical reaction or an electrical principle. The thrust indicates how much force, in newtons (N), the propulsion system exert on the vehicle. Let us denote _ m p as the mass flow rate, the exhaust velocity U ! ex and g is the acceleration due to gravity, then spacecraft's thrust denoted by The performance of thrusters is usually determined by thrust T, which is the total force undergone by the rocket. Thrust also has same unit as a force in newton, which shows the movement of the propulsion system. Thrust, is generated by the burning of fuel or by the electrostatic forces. The thrust T ¼ _ m p U ! ex , if the mass flow rate is constant. The specific impulse I sp is used to compare the efficiencies of different type of propulsion systems [2]. The specific impulse is expressed as I sp ¼ T _ m p g . In general, the higher the specific impulse the less fuel is required. Therefore the specific impulse simplifies to The specific impulse has the dimension of time and is a measure for the effective mission time of the thruster. The high value of the specific impulse reduces the mission time. If we denote the thrust efficiency η and the input power P t , then these are related by Tsiolkovsky rocket Eq. (1) can be read as The above Rocket equation defines the change in velocity of a spacecraft. It is clear that a higher d υ ! demands more propellant. In terms of specific impulse, the above equation simplifies to We can now say that I sp plays a key role in the design of a space mission propulsion system.

Description of the Hall thruster
This description of the Hall thruster is shown in Figure 1. The anode and cathode set up an axial electric field and magnetic coils create a radial magnetic field. First cathode starts producing a stream of electrons and these electrons are attracted by positive anode. When electrons are moving to anode, then at the channel exit they face of perpendicular electric and magnetic fields, these fields are more strong at channel exit. Due to these perpendicular fields, electrons trapped in an ExB drift and formed Hall current [1]. At this time Xenon gas is released from the anode, when neutral atom of gas reached at the channel exit, then electron collides with neutral atoms and ionized them. These ions are accelerated out of channel by electric field at the channel exit and this motion of ions imparts a reaction force on the thruster in reverse direction. The cathode is also used to neutral the ions charge so it produce a stream of electron to neutral the ions [1-10].

Stationary plasma thruster (SPT)
The wall material of this type of thruster is dielectric like borosil (BN-SiO2), boron nitride (BN) and alumina. This type of material has low secondary electron emission coefficient with Xenon ion interaction. Most of SPT use Xenon as a propellant because of its higher mass (131.3amu), lower first ionization potential, less toxicity, ionization cross section of ($2.310 À6 cm 2 ) and of its desirable thermodynamics properties [1,10].

Thruster with anode layer (TAL)
These types of thruster has metallic conducting walls and has narrow acceleration zone associated with the narrow electric field region near the anode. The ratio of channel width and channel depth in these thruster is 2:1. The conducting channel wall is negatively biased and it is a part of magnetic circuit so it prevent electron to move in direction of wall and repel them to ionization region and reduce electron power losses [1][2][3][4][5][6][7][8][9][10].

Components of a Hall thruster
The main components of a Hall thruster are body, magnetic coils, discharge channel, anode and cathode. The body of the Hall thruster provides better shape of external magnetic field, so it is normally made up of iron (steel). In this thruster a single thick disk shape annular discharge channel exist on the front face. To create better shape of magnetic field two type of magnetic coils are situated in the thruster channel. The inner coil is made of single reel and located radially inward in the channel and the outer coil is made of multiple reels and located radially outward in the channel. The magnetic coils and iron body made a magnetic circuit. The magnetic iron body of the thruster is separated from thruster discharge channel by walls and the material of these walls is metal or ceramic. The material of the anode is normally stainless steel, which avoids magnetic interaction and supply hardiness [1][2][3][4][5][6][7][8][9][10]. To set up an axial electric field in discharge channel of thruster a cathode is required and this cathode is normally hollow cathode with lanthanum hexaboride or barium oxide. The cathode completes the discharge circuit and work like an electron source. This description of the Hall thruster provides knowledge about the structure of thruster.

Hall current and thrust
As discussed earlier, there is an azimuthal electron drift in a Hall thruster channel, which is normal to both the applied electric field and generates a Hall current [1,10]. Because of the collisions of the electrons with neutrals, electrons, ions and potential fluctuations in the plasma, generate the axial electron current density. The azimuthal E X B drift is given by The Hall current may be approximated by integrating the magnitude of E r =B z along the acceleration region and multiplying the result by the electron charge density and width. In mathematically, it can be read as Here, w is the channel width and V d is the voltage at cathode.

Channel length and scaling laws for larmor radius
The ratio of electric and magnetic field is such that the ion's gyro radius is much larger than electron's gyro radius, so that ions are not magnetized inside the channel. The channel length is calculated by determining the Larmor radius of both the plasma species [10]. The motion of the moving charged particle under the electromagnetic fields defined as follows This gives the radius of gyration Here, Ω c ¼ qB m , is called the cyclotron frequency. If ions are accelerated through electrical potential V ⊥ (perpendicular to the magnetic field), then energy balance leads to mυ ⊥ 2 2 ¼ qV ⊥ . This implies to These above equations gives the larmor radius in terms of the applied potential The magnitudes of the fields are such that r i > > L > > r e , where L ($6 cm) is the length of the acceleration channel. For a typical Hall thruster, Larmor radius for electrons ($0.13 cm) and ions ($180 cm) corresponds to the radial magnetic field strength of order 150 G and energy 300 eV.
Despite many successful applications of Hall thrusters, some aspects of their operation are still poorly understood. One notable problem is the anomalous electron mobility [16,17] and plasma sheath, which is far above the classical collisional values. It has been established that the inhomogeneous plasma under the electromagnetic fields is not in the thermodynamically equilibrium state [17][18][19][20]. The equilibrium E Â B electron drift, ion flow rate, plasma and magnetic field gradients are all sources of plasma instabilities in Hall plasmas. Hall plasmas devices with ExB electron drift demonstrate wide range of turbulent fluctuations. These fluctuations are probably the reason of the observed anomaly in the electron transport across the magnetic field [21][22][23] and other nonlinear phenomena (coherent rotating spoke) [24][25][26]. Understanding of the mechanisms of the coherent structures and anomalous transport requires the detailed study of linear instabilities in Hall plasma devices. These instabilities are also considered to be a principal source of anomalous transport in toroidal magnetic confinement devices [2].

Oscillations and instabilities in Hall thrusters
If free energy is available in the system and even though system is in equilibrium in the sense that all the forces are in balance, then these oscillations can grow at the cost of free energy and hence instabilities can take place. There are different types of instabilities that depend on different conditions. For proper description of a particular instability, one should be able to define the mode of the growing wave, the nature of the growth and the source of the free energy. Instabilities are mainly classified into four groups, namely streaming instabilities, Rayleigh-Taylor instabilities, universal instabilities and kinetic instabilities.
When there is any kind of perturbation, the free energy available excites the waves and the plasma waves no longer remains in thermal equilibrium. Even though there exist an equilibrium because all the forces are balanced and there is no net force and it is possible to find a time independent solution to the wave. Perturbation makes the plasma waves unstable, which is always a motion that brings the plasma closer to true thermodynamic equilibrium by decreasing the free energy. Instabilities may be classified according to the type of free energy available to drive them. Few of them has been explained below.

Streaming instability
This type of instability occurs, when either a current or a beam of energetic particles is driven through plasma so that the different species of particles have drifts relative to one another. This drift energy attempt to excite waves and oscillation. This energy is acquired at the loss of the drift energy, which is in the unperturbed state.

Rayleigh-Taylor instabilities
In this kind of instability, the plasma has a sharp boundary or a density gradient, so that it does not remain uniform. In addition to this, an external, nonelectromagnetic force is applied into the plasma. This force is responsible for driving the instability in plasma. This analogy can be realized in an inverted glass of water. Though the plane interface between the air and the water is in the state of equilibrium, where the air pressure support the weight of the water. Any ripple arising in the surface of water tend to grow at the loss of potential energy in the influence of gravitational field. Whenever a light fluid supports a heavy fluid this things happen, which is quite known in the field of hydrodynamics [1].

Universal instabilities
A plasma is hardly present in perfect thermodynamic equilibrium, when it is confined by gravitational field or an electric field (driving forces). The plasma is expanded by plasma pressure and an instability is driven by the expansion energy. Any finite plasma always contains this type of free energy and the waves, which comes out as a result are called universal instabilities.

Kinetic instabilities
Generally, the velocity distributions are assumed to be Maxwell-Boltzmann in fluid theory. If there is a case, where distributions are not Maxwell-Boltzmann, then there may be a departure from thermodynamic equilibrium and this anisotropy of the velocity distribution drive the kinetic instabilities.

Streaming instabilities
These kind of instabilities occur, when the plasma particles streams with their relative drift, which may be driven due to the travel of charge particle beam or internal driven current. For example, the two stream instability is due to the relative drift of ion and electron streams.

Electromagnetic resistive instability
These instabilities have been investigated in various positions of the acceleration channel of the thruster. The effect of radial magnetic field, thermal motions of plasma particles and electron collisions can induce time varying fields in the discharge oscillations. This can prompt an electromagnetic resistive instability in the Hall thruster. In this chapter, we derive the dispersion relation for the electromagnetic instabilities in a Hall thruster and conditions for the instability.

Oscillations and instabilities in Hall thrusters
There are numerous types of oscillation found in thrusters which propagates in azimuthally and axially direction ranging from a few kHz to tens of MHz [1,10]. These oscillations may reduce the specific impulse and the efficiency of a Hall thruster. These disturbances can also limit the operating life of a Hall thruster and therefore, suppression of this oscillation has become an essential task for Hall thrusters. These fluctuations are responsible for electron transport across magnetic field lines, performance and ionization of propellant [27][28][29][30]. The magnitude of these oscillations strongly depend on the magnetic field, location of the cathodes, the discharge voltage and the mass flow rate.
Low frequency oscillation, frequently referred to as the breathing mode, is intimately tied to the details of propellant ionization and eventual ion acceleration and manifests itself as a strong 10-30 kHz oscillation in the thruster discharge current. Breathing mode models suggest the presence of a propagating ionization front traversing the channel of the thrusters [31]. Benítez and Ahedo investigated the axial-azimuthal instabilities in the global discharge region of a Hall-thruster to identify dominant mode (develops in the near plume at 1-5 MHz) and subdominant mode (develops near the anode100-300 kHz) [32]. Lafleur et al. studied transport effects of the electron drift instability in Hall-effect Thrusters [33]. Fan et al. studied the effects of the peak magnetic field position on Hall thruster discharge characteristics [34]. Sekine et al. investigated the spatially and temporally resolved ion flow measurements inside the plasma source of an inductive radio frequency plasma thruster [35]. Puerta et al. generalized non-ideal treatment and growth rates analysis of drift waves instabilities in a collisions-free magnetized dusty plasma [36]. The electrostatic dispersion relation for an unbounded homogeneous plasma in the presence of unmagnetized ions, magnetized electrons and an applied magnetic field has been solved numerically by Mikellides and Ortega in the near-plume of a magnetically shielded Hall thruster [37]. Tomilin and Ivan Khmelevskoi studied the influence of kinetic effects on dispersion properties of high-frequency perturbations in Hall thruster plasmas [38]. Marcovati et al. reported the dynamic behavior of gradient-driven drift waves in a strongly magnetron discharge in multi ion plasma [39]. Litvak and Fisch [40] investigated resistive instabilities in a Hall plasma and found that plasma perturbations in the acceleration channel are unstable in the presence of collisions. Fernandez et al. [41] did simulations for resistive instabilities. Marusov et al. [42] modeled the stability of gradient-drift waves in a Hall-type plasma using two-fluid ideal magnetohydrodynamics. Ducrocq et al. [43] studied high-frequency electron drift instability, where they derived threedimensional dispersion relation for a model of a crossed electric and magnetic field configuration existing in the Hall thruster. Litvak and Fisch [44] have analyzed gradient driven Rayleigh type instabilities in a Hall thruster using two fluid hydrodynamic equations. Kapulkin and Guelman [45] investigated low frequency instability in near anode region of a Hall thruster, where they obtained that the instability can be responsible for the enhanced transfer of the electrons between the ionization region and the anode. Choueiri [46] has quantitatively discussed the nature of oscillations in the 1 kHz-60 MHz frequency range observed during operation of Hall thrusters. Various plasma parameters measured inside the accelerating channel of a typical Hall thruster were used to evaluate the various stability criteria and dispersion relations of oscillations [46].
At small amplitudes, the oscillations can be considered a part of normal operation with no significant effect on operation. At large amplitudes, the oscillations can severely and adversely affect operation. The details of these oscillation are given in Table 1.
Lakhin et al. have developed the effects of finite electron temperature on gradient drift instabilities in partially magnetized plasmas in the frequency range ω Bi ≪ ω ≪ ω Be driven by the equilibrium current perpendicular to the magnetic field [56]. Romadanov et al. [57] studied the structure of nonlocal gradient-drift instabilities in Hall E Â B discharge plasma. Koshkarov  10-100 kHz.

Flight oscillations
These oscillations are also called ionization flight oscillations, because they are determined by the change of ionization rate due to the delay of particle appearance, from one region to another. The analysis is based on the concept that plasma particles are delayed in being transferred from one region to other [54].  for Rayleigh type instability under the effects of thermal motions of ions and plasma resistivity induces resistive instabilities (electrostatic and electromagnetic) [62][63][64][65] associated with azimuthal and axial directions. Yadav et al. presented the model for relativistic electron-beam assisted growth of oscillating two-stream instability [66]. Aria and Malik [67] have investigated the propagating modes, instabilities and plasma sheath formed on the outer surface of a spacecraft. The detailed physical picture of the processes in the thruster is very complex. It includes a whole series of phenomena, such as stabilization of the flow in cross-fields. Becatti et al. investigated the properties of plasma oscillations in the exterior region of a high-current hollow cathode [68].

Magnetic field profiles and erosion problems
Magnetic field is an important parameter, which affect the performance and operation of Hall thruster. The erosion on the channel walls and on the electrodes can be minimized by accelerated beam of ions to a narrower beam width and by use of appropriate profile of magnetic field. The radial magnetic field causes the erosions of the walls, so new topology of magnetic field 'lens' is proposed by Morozov [69]. By using magnetic shielding technique, the discharge chamber erosion rate can be reduced by orders of magnitude [70]. Morozov and Lebedev proposed a magnetic field lens to focus the plasma beam [71]. Morozov et al. have designed a lens-type magnetic field with a zero magnetic point to make the plume divergence half angle only 10°in SPT-ATON Hall thruster [72]. Hofer et al. showed that the performance of the Hall thruster can be enhanced by reducing the divergence of the plume that could damage the solar panels and other parts of the satellite [73]. Hofer et al. used magnetic field to control the unmagnetized ion beam that formed in Hall thruster. By controlling ion beam the wall erosion was reduced to 2-3 order by ion bombardment [74]. Huang et al. studied the effect of background pressure on performance and plume of NASA's High Voltage Hall Accelerator Hall thruster [75]. Their result shows that discharge current and thrust are increases with pressure and ion beam current, ion energy per charge, plum divergence decreases with increasing background pressure.
Liu et al. studied the effect of azimuthally electron drift on sheath profile and anomalous erosion in thrusters. Their results show that azimuthally electron drift induce sheath oscillations and it can produce an asymmetric sheath structure. To simulate the azimuthally erosion evolution, an erosion modal is used and it has been concluded that the azimuthally asymmetric ion sputtering is responsible for an asymmetric erosion profile [76]. Kim studied the ionization processes and ion dynamics in the accelerating channel to determine the stationary plasma thrusters performance levels [54]. Choueiri theoretically studied the difference between stationary plasma thruster and thruster with anode layer by measuring the temperature of secondary electron emission from the walls of thruster [77]. Hong et al. studied the effect of wall grooves on Hall thruster discharge to improve the performance of Hall thruster. If wall grooves are present in ionization region it increases near wall conductivity and decrease electron transient time, thrust and efficiency [78]. Ding et al. studied the discharge current and stability in graphite walls and BN-SiO 2 walls for magnetic shielded and unshielded thruster. Their result shows that magnetic shielded thruster does not show change in stability and discharge current but 25% discharge current increases in unshielded thruster [79]. Experimental results and PIC simulation show that oblique channel's specific impulse, anode efficiency, thrust, propellant utilization and ionization in plume region is improved 20% rather than the straight channel thruster [80]. Olano et al. studied the effect of magnetic field configuration on thruster performance and plasma discharge by proposing three types of configurations: (A) nominal, (B) orthogonal magnetic field and (C) high magnetic field [80,81]. Garrigues et al. did PIC simulations and shows that in a Hall thruster electric discharge produce due to wall-plasma interaction and wall of thruster channel is reduced due to interaction with ions [82]. The electrostatic and magnetic probes are used to investigate the electromagnetic fluctuations and coherent magnetohydrodynamic azimuthal modes in thruster [68].

Introduction to electromagnetic instabilities and their dispersion relations
The resistive instability is driven by coupling to a dissipative process. Due to the collisions between the electrons and neutral particles, resistive instability can occur in the acceleration channel of the Hall thruster. This instability occurs due to the interaction of the wave with the electrons' flow in the presence of electron collisions. The two major problems in plasma confinement are equilibrium and stability of plasma. The system in an equilibrium state if all the forces, which act on a system are balanced but stability and instability of the equilibrium can be assured by giving some perturbations to the equilibrium state. The stable and unstable state of equilibrium depend on small perturbation whether the perturbations are damped or amplified. For small perturbations, equilibrium is non-linear but stability can be linearized.

Plasma model and basic equations for purely azimuthal waves
For the case of small amplitude perturbations and wavelengths much smaller than the scale lengths of inhomogeneities, the analysis of linearization can be applied. In the simplest approach, we consider the x-axis is taken along the axis of the thruster and the z-axis is taken along the radius of the thruster. The direction the magnetic field B ! is along the z-axis. The y-axis is taken correspond to the azimuthal direction. Consistent to the fluid approach, we write below the basic fluid equations where n j is the mass density and υ ! j is the velocity of species j (j = i, e). The momentum equations for electrons and ions are

Linearization of fluid equations
To linearize all the equations, let us write The unperturbed density is taken as n 0 , electric field (magnetic field) as E ! 0 (B ! 0 ) and the perturbed value of the electric field (magnetic field) is taken as E ! 1 (B ! 1 ). Here, we consider the perturbed densities for ions and electrons as n i1 and n e1 velocities as υ ! i1 and υ ! e1 indicated by subscript 1 along with their unperturbed values as υ 0 and u 0 in the x-and y-directions respectively. In view of small variations of both the density and magnetic field along the channel, the plasma inhomogeneities are neglected. The oscillations of the perturbed on and electron densities are taken small enough n i1 , n e1 < < n 0 ð Þ so that the collisional effect due to the velocity perturbations dominate over the one due to the density perturbation. Since υ

Dispersion equation and growth rate of azimuthal waves
We take the variation of oscillating quantities in azimuthal direction as $ exp iωt À iky ð Þ . The linearized Eqs. (14)- (17) are used and the density and velocity perturbations are expressed in terms of the electric field as From Eq. (15) From Eqs. (13) and (14) The x-component of the perturbed current density 24) and the y-component of the perturbed current density

Conductivity tensor
From the Maxwell's equation, we have Faraday's law gives the relationship between changing electric and magnetic field as For a plane electromagnetic wave Where E ! is the electric field, B ! is the magnetic field, j represents the complex number, k ! is the wave vector, t is the time, E 0 ! and B 0 ! is complex magnitude of electric and magnetic field. Then ∇ operation gives ik and ∂ ∂t gives Àiω. Substituting these operators Faraday's law become

Permittivity tensor
From Maxwell's equations, we get which on expansion will give x Àk x k y Àk x k z Àk y k x k 2 À k 2 y Àk y k z Then permittivity tensor will be x Àk x k y Àk x k z Àk y k x k 2 À k 2 y Àk y k z Àk z k x Àk z k y k 2 À k 2 In general But for a pure dielectric medium k ¼ ω c ffiffiffiffi ε r p and we will get ε r ¼ ε rr À ε rx Àε rx ε ry Àε rx ε rz Àε ry ε rx ε rr À ε ry Àε ry ε rz Àε rz ε rx Àε rz ε ry ε rr À ε rz Then, the Maxwell's equations are used in view of the perturbed electric and magnetic fields of the electromagnetic wave, and the plasma dielectric tensor ε ij is obtained as Finally, the wave equation k 2 δ ij À k i k j À ω 2 c 2 ε ij E j ¼ 0 is written in the following form Where, the components of the dielectric tensor are obtained from Eq. (34) with the help of the Eqs. (24) and (25) By substituting these components into Eq. (35) we get the following cumbersome analytical expression of the dispersion relation of electromagnetic waves propagating in magnetized plasma [40].

Typical parameters of Hall thrusters
The values and ranges of some typical parameters are given in Table 2.

Numerical results and discussion
We solve the dispersion Eq. (40) to find out complex root by using typical values of the magnetic field, azimuthal wave number, collision frequency, electron drift velocity, ion drift velocity and electron temperature. Then the effect of these parameters on the growth γ of the electromagnetic wave is studied in Figures 1-4. Figure 2 shows that the growth rate of the wave get enhanced for the larger values of the drift velocity of the electrons [64]. Since the drift velocity can be correlated with the discharge voltage, so it can be said that the growth rate is increased with the discharge voltage. Esipchuk and Tilinin [83] also reported the proportionality of the frequency of drift instability to the discharge voltage. The increase in the growth rate may be attributed to the strong coupling between the electric field and electron current [84]. Figure 3 shows the variation of growth rate under the effect of collisional frequency. It is seen that the wave grows at a faster rate in the presence of more electron collisions. Since the stronger resistive coupling of the oscillations to the electrons' closed drift requires the electron collisions, it is obvious that this instability grow faster in the presence of higher collision frequency. Similar results were also reported in the simulation studies of resistive instability by Fernandez et al. [41] that the growth rate is directly proportional to the square root of the collision frequency.
The dependence of growth rate on the magnetic field is shown in Figure 4, where it is observed that the wave grows faster in the presence of strong magnetic

Results and the discussion
The different aspects of the Hall thrusters have been reviewed in this chapter along with future challenges related to the performance and efficiency. The different types of turbulence and oscillation with frequency ranges are also summarized. Hall thruster Plasma support electrostatic and electromagnetic waves under the influence of resistive effects. Therefore the waves (electrostatic and electromagnetic) propagating in azimuthal direction in a Hall thruster channel are found to be unstable due to the resistive coupling to the electrons' closed drift in the presence of collisions. The theoretical model for the propagation of electromagnetic instability is derived in a Hall thrusters. The dispersion relation for the electromagnetic instability is derived analytically. The dispersion relation is solved numerically with the help of MATLAB to study the growing and propagating modes. The dominated modes are plotted to observe the behaviors of the instability. accelerators with closed electron drift and extended acceleration zone Proc. 5th All-Union Conf. on Plasma [55] Bugrova A I and Kim V 1984 Modern state of physical studies in accelerators with closed electron drift and extended acceleration zone pp 107-28 in