Recent Progress of Electrocatalysts and Photocatalysts Bearing First Row Transition Metal for Hydrogen Evolution Reaction (HER)

The design and modification of metal – organic complexes for hydrogen (H 2 ) gas production by water splitting have been intensively investigated over the recent decades. In most reported mechanistic pathways, metal hydride species are considered as crucial intermediates for H 2 formation where the metal present at the active site plays an imperative role in the transfer of electron and proton. In the last few decades, much consideration has been done on the development of non-precious metal – organic catalysts that use solar energy to split water into hydrogen (H 2 ) and oxygen (O 2 ) as alternative fossil fuels. This review discussed the design, fabrication, and evaluation of the catalysts for electrocatalytic and photocatalytic hydrogen production. Mechanistic approach is addressed here in order to understand the fundamental design principle and structural properties relationship of electrocatalysts and photocatalysts. Finally, we discuss some challenges and opportunities of research in the near future in this promising area.


Introduction
Climate change and increasing energy demand have emphasized research on sustainable energy source [1,2]. Day-by-day increase of human population and global requirements has compelled researchers to develop new renewable sustainable energy sources in replacement of hydrocarbon deposits [3]. Renewable sources such as solar power, wind, and water, storage of these energies for on-demand utilization, and transportation are the major challenges for researchers. To develop a clean and eco-friendly environment, splitting of water into hydrogen and oxygen is a tremendous way to produce sustainable energy. Hydrogen gas emerged as a green energy fuel due to its high-energy density and zero carbon dioxide (CO 2 ) emission [4][5][6]. In this regard, electrocatalytic and photocatalytic H 2 generation from water has been considered as one of the most striking approaches [7][8][9]. In recent years, a substantial number of artificial photosynthesis have been developed, exploited solar power as electron and proton source to make a clean renewable fuel [10][11][12][13][14]. Light-induced splitting of water is a suitable process because the production of hydrogen is used as green fuel in future and even used for the synthesis of other chemicals [15][16][17][18].
Literature reports suggested more than 500 billion cubic meters (44.5 million tons) of hydrogen gas is produce yearly worldwide [19,20]. In the current scenario, steam methane refining, coal gasification, and water electrolysis are the major way for hydrogen production. Nowadays 95% hydrogen gas is produced from steam methane reforming and coal gasification, however only 4% hydrogen from water electrolysis. Steam methane is a high-energy-intensive process maintained at high temperature with the formation of carbon dioxide and carbon monoxide: (i) CH 4 + H 2 O = CO + 3H 2 (ii) CO + H 2 O = CO 2 + H 2 . Hence, it is not an eco-friendly method for hydrogen production. Water electrolysis is the most sustainable and clean approach for hydrogen production because its source is abundant. Since the most suitable way of light-driven energy conversion is water electrolysis, artificial photosynthesis (PS II) has been considered as primary goal to produce electron and proton [21,22]. Water splitting is a redox reaction in which aqueous protons are reduced into H 2 at cathode and water is oxidized to O 2 at anode [23]. Both H 2 (HER) and O 2 (OER) reactions are rigorously coupled, which may lead to the formation of explosive H 2 /O 2 mixtures due to gas crossover [24][25][26]. By far, only a few stable metal complexes as catalysts are achieved that can decompose water into H 2 and O 2 [27][28][29][30][31]. Water-splitting reactions are split into two half-reactions: water oxidation to O 2 evolution and water reduction to H 2 production: The limitation of OER is that it takes place after the successive accumulation of four oxidized electrons and protons in Kok cycle (catalytic cycle of the water oxidation in PS II) that require much higher overpotential input than that of HER [32]. Thermodynamic potential is different for H + /H 2 (0 V vs. NHE) and OH -/O 2 (1.23 V vs. NHE), and the overall solar energy conversion efficiency is only $15% in OER [33]. The hydrogen evolution reaction (HER, 2H + + 2e -= H 2 ) is the cathodic reaction with the two-electron transfer in one catalytic intermediate and offers the potential to hydrogen production. However, hydrogen production technology requires proficient electrocatalysts and photocatalysts which support two key electrode reactions (OER and HER) at lower overpotentials.
Moreover discussion on the mechanism of HER, H + adsorption on the hydrogen evolution catalyst surface is the first step, known as Volmer step, followed by Heyrovsky or Tafel steps shown in Figure 1. A suitable HER catalyst always binds H + very fast and releases the product. Hence, electrochemical hydrogen evolution reaction (HER) facilitates for H 2 production on large-scale.
Afterwards, H 2 evolution may occur via two different reaction mechanisms depending on the action of catalyst [34]. Hydronium cation (H 3 O + ) is the proton source in acidic solution, and in alkaline condition H 2 O is the proton source. In Volmer-Tafel mechanism, two protons absorbed on the catalytic surface can combine to form H-H bond to yield H 2 . In Heyrovsky reaction route, a second electron and another proton from the solution are transferred to the catalyst surface which reacts with the absorbed H atom and generate H 2 . This is an electrochemical desorption pathway. Precious metal like Pt-based electrocatalysts is highly reactive for HER and is usually pursuing Volmer-Tafel mechanism. Lately few literatures [35][36][37] have been reported on Ni-based electrocatalysts which follows Volmer-Heyrovsky path.

Fundamental aspects of photocatalytic and electrocatalytic hydrogen production process
Electrocatalytic water splitting is driven by passing the electric current through the water; conversion of electrical energy to chemical energy takes place at electrode through charge transfer process. During this process, water reacts at the anode form O 2 and hydrogen (proton) produce at the cathode as we mentioned earlier. Suitable electrocatalysts can maximally reduce the overpotential which is highly desirable for driving a specific electrochemical reaction. However, the process of surface catalytic reactions in electrocatalysis is very similar to photocatalysis [38]. Photocatalytic is a simple water-splitting reaction in which H 2 and O 2 are produced from water by utilizing the energy of sunlight. Figure 2(a) shows the process of photocatalysis in which a metal catalyst contains chromophores that  immersed solar energy and triggered the electron transfer reaction. The most important criteria for the solar-driven water-splitting reaction are electronic band gap matching of the photosensitive material to the redox potential of water [39]. Metal complexes act as chromophore associated with mainly three types of electron transfer: metal center (MC), ligand center (LC), and metal-ligand center transition (MLCT). The MLCT state of the metal complex plays a crucial role in photocatalytic reactions. In octahedral complexes with conjugated ligand system, the highest occupied molecular orbital (HOMO) corresponds to the metal-localized t 2g -orbitals, and the lowest unoccupied molecular orbital (LUMO) is associated with antibonding π*-orbital localized on the ligands. On the absorption of UV-visible light, an electron is promoted from one of the metal-centered t 2g orbitals to a ligandcentered π* orbital, resulting in the MLCT state shown in Figure 2(b). As a result, the redox properties of the metal complexes are dramatically changed. The excited metal complexes behave as better oxidants and better reductants than their electronic ground state and can hold more thermodynamic driving force for the charge transfer reactions. Based on the photo-induced redox potential changes and the long-lived lifetime of the excited state, many metal complexes have been intensively investigated as chromophores for this photocatalytic H 2 production purpose [40]. Zou and coworkers have described various photocatalytic systems for H 2 production, which exposed that most of the photocatalytic systems suffer photodecomposition and instability [40]. Hence, for long-term use, it is imperative to build up highly proficient H 2 generation systems with long lifetimes and high durability. Many reviews have been published on solar H 2 evolution systems based on photocatalysts [41][42][43][44].

Mechanistic pathway
So far, extensive theoretical study has been revealed, the possible mechanistic process of proton reduction to hydrogen evolution through transition metal molecular catalyst. A generalized mechanistic scheme depicting the homolytic and heterolytic path is shown in Figure 3. The homolytic mechanism involves bimetallic route, where a metal hydride species ([M n+ -H]) react with another metal hydride to release one H 2 via reductive elimination. Instead, heterolytic is a monometallic  [45]. Both pathways function simultaneously, two protons and two electrons are delivered to the metal center, and in few cases, the pH, catalytic concentration, and proton source decide the dominant route [46]. During the past decade, a number of review articles emphases on the structural property relationship and mechanistic study [45,[47][48][49]. Among all research on catalyzed H 2 evolution, the mechanistic investigation on proton reduction catalysis is essential because it can give us a significant idea to design better molecular catalysts in the future [49].

Metal and redox-active ligands for HER
Here we start by describing the fundamental concept of metal and organic ligand system which gives a strong influence on the performance of H 2 evolution. Transition metal cations with partial filled d-electronic configurations are considered as catalyst. The characteristic feature of this type of catalyst is that the metal ions can exist in higher oxidation state [44]. There are several literatures reported with partially filled d-orbital which show high stability toward water-splitting reactions [50][51][52][53]. However, the most catalytic system requires very high temperature and precious metal at the active site; therefore, it will be a challenge for researchers to develop a photocatalytic and electrocatalytic system at low temperature with lowcost metal [54][55][56][57]. Indeed, first-row transition metal complexes (Co, Ni, Cu, Zn) have been exploited in the last few decades for this purpose. Beyond the reactivity of metal, the redox activity of organic ligands has also received continuous attention. The redox-active ligand works as electron sink in the complexes and maintains the metal in its original oxidation state. Redox-active ligands convey a novel reactivity to the complex by loss or gain of electrons [58]. In addition, the redox-active property of the ligand can also be influenced by the modification of the substituents by σ and π donating ability, π accepting ability, and conjugation [59]. A highly conjugated system such as bpy, porphyries, and ortho-phenylenediamine (opda) having anti-bonding π*-orbital localized on the ligands is considered for hydrogen production due to its multielectron or multiproton pooling ability which is responsible for dramatically changing the potential of redox properties [60,61]. Substituents attached to redox-active ligands, electron density, and charge on the metal ions also effect the standard electrode potential.
So far, considerable advancement has been done in the field of electrocatalytic and photocatalytic water-splitting reaction for hydrogen production, and several advance review papers have been reported by scientists [40,51,[62][63][64]. However, very limited comprehensive tutorial has published on only first-row transition metal-based catalysts. This chapter describes electrocatalytic as well photocatalytic properties of inorganic catalysts and their structural and mechanistic features. Here we put an effort elucidate the direction of fundamental mechanistic aspects during electrocatalytic and photocatalytic hydrogen (H 2 ) production reaction (HER).

Photochemical hydrogen production from a series of 3D transition metal complexes bearing o-phenylenediamine ligand
Masaki Yoshida et al. [65] developed a series of 3D-transition metal complexes with o-phenylenediamine (opda) ligands for hydrogen production due to the following properties: (a) aromatic amine undergoes homolytic N-H bond cleavage by photoexcitation [66] which is applicable for hydrogen production under mild condition, and (b) opda complexes have extensively been obsessed as reversible multielectron or multiproton pooling ability because of its multistep redox processes between o-phenylenediamine(opda), semibenzoquinodiamine (s-bqdi), and o-benzoquinodiimine (bqdi) which is useful for reversible hydrogen production. [M(opda) 3 ], M = Mn 2+ , Fe 2+ , Co 2+ , Ni 2+ , and Zn +2 complexes (1-5) shown in Table 1 have photochemical hydrogen production ability.
a. Photochemistry of aromatic amine (opda) b. Redox properties of opda complex In the past M. Yoshida and coworkers proposed [Fe-opda] for photochemical HER mechanism at photoirradiation of λ = 298 nm; ππ* excitation occurred in complex with N-H bond homolysis process, followed by H 2 elimination [67]. After this process, the opda ligands in the complex were partially oxidized to bqdi or sbqdi ligands. This mechanism is based on the deep-rooted photochemical N-H bond activation of aromatic amines. Theoretical study and ultrafast spectroscopic studies of amino benzene support that the photochemical N-H fission occurs by the photoexcitation to higher-lying ππ* level which leads to the formation of the πσ* state [68]. Photochemical mechanism for HER of all complexes is shown in Figure 4.
All opda-based metal complexes display photochemical HER activities with the formation of almost one equivalent of H 2 gas. However, the HER was not observed at all in the dark in all complexes, which suggests that the HER was obsessed by photochemical reaction. Moreover, they observed remarkable decrease in hydrogen evolution reaction, while the ligand is replaced with aromatic amines. This experiment suggested that the photo-induced HER activities of the complexes in this case are weakly dependent on the central metal ion and strongly dependent on the redox-active ligand. Further to check the metal ion dependency, examine the catalytic hydrogen production in the presence of hydroquinone (HQ ; 10 equiv) as a sacrificial electron-proton donor. The photochemical H 2 production from [M-opda] (7.98 Â 10 À2 mmol) with HQ (7.98 Â 10 À1 mmol) in THF (4 mL) under an N 2 atmosphere at 20°C for 190 h turns over the number for all the complexes given in Table 2. Difference in TON may be caused by the stability of each complexes.

Cobalt diimine-dioxime complexes for HER
V. Artero and coworker synthesized cobalt diimine-dioxime complexes as molecular catalysts for H 2 evolution [69,70]. This synthesized ligand (N 2 , N 2 À propanediylbis-butan-2-imine-3-oxime) has emerged many years ago through Schiff base condensation of butanedione-monoximeon diamine compounds but not widely used for HER. Cobalt diimine-dioxime catalysts are active for H 2 evolution in aqueous solution, both after immobilization on electrode materials and in lightdriven homogeneous conditions. The electrocatalytic activity of complexes (6) and (7) for hydrogen evolution was supported gas chromatography and by cyclic voltammetry study illustrated in Figure 5 with the appearance of an irreversible wave. In the case of the BF 2 -associated complex (7), the electrcatalytic wave which developed toward negative potentials corresponds to the Co II /Co I couple in contrast to the H-bridged complex (6), electrocatalytic H 2 evolution occurs at potentials positively shifted with regard to the Co II /Co I couple.

Electrocatalytic cycle for H 2 evolution
In the electrocatalytic cycle, V. Artero and coworker observed that in acetonitrile medium, halide ligands are banished with reduced oxidation state from Co II to  Co I . Upon reduction, the coordination in number decreases from six in Co II state to five in Co I state; this characteristic was supported by DFT calculations [71]. In the catalytic cycle (Figure 6), the first step is the transfer of electron and proton by proton-coupled electron transfer (PCET) process. PCET is a chemical reaction that   involves the transfer of electron and proton in which the oxidation number changes by Co II to Co I . In the second steps, further electron and proton transfer takes place by PCET process, and the oxidation number changes from Co I to Co II . In the last step, H 2 is produced in dihydrogen bond through an intramolecular mechanism. The authors also confirmed cobalt diimine-dioxime catalysts 6 and 7 active for H 2 evolution under light-driven conditions in the presence of photosensitizers, associated with Ru, Ir, or Re derivatives. The photocatalytic activity of 6-Br 2 was observed in mixed H 2 O/CH 3 CN solvent in the presence of TEA and cyclometalated iridium-based photosensitizer [72]. Turnover numbers (TON) determined after continuous 4 h UV-visible light irradiation 6-Br 2 showed 300 (H 2 mol cat À1 ), whereas 7-Br 2 complex shows only 50 (H 2 mol cat À1 ) as shown in Table 2.
Similarly, cobalt bis(iminopyridine) complex 8 was prepared for electrocatalytic water-splitting reaction [73]. The ligand-centered redox activity was observed during the cyclic voltammetry, suggesting the considerable role of redox-active ligand which is completely involved to stabilize the cobalt metal in higher oxidation state. The two reduction potentials were observed for the Co III /Co II (quasi reversible) and Co II /Co I (reversible) couples at À0.34 V and À0.86 V (vs. Ag/AgC), respectively. The improved water reduction was attributed to the assimilation of a redox-activeligand to cobalt which facile reduction of [Co-H] n+ species.

Zn II and Cu II complexes for HER
Grapperhaus et al. [74] recently reported two homogeneous electrocatalysts for H 2 production. They derived bis(thiosemicarbazones) ligand from 1,2-diones, considered as a kind of multitalented redox non-innocent system. Tetra-coordinated N 2 S 2 is able to bind with low-valent transition metals centered and formed to stable neutral complexes (9, 10) ( Table 1). Zn II complex 9 containing a redox-active moiety diacetyl-bis (N-4 methyl-3-thiosemicarbazide) exhibits the homogeneous catalysis of electro-driven H 2 evolution through proton reduction with a maximum of TOF 1170 s À1 in CH 3 OH and 11,700 s À1 in CH 3 CN at an overpotential of 0.756 V and 1.074 V, CH 3 COOH used as proton source. Bulk electrolysis showed that the TON of H 2 evolution of Zn II is 37 in over 2.5 h experiments. To make this more comparative, Grapperhaus and coworker synthesized another Cu II complex with similar ligand diacetyl-bis(N-4-methyl-3-thiosemicarbazide) and examined H 2 evolution reaction. Cu II complex 10 exhibits a maximum TOF of 10,000 s À1 in CH 3 CN and 5100 s À1 in DMF at an overpotential of 0.80 and 0.76 V, respectively. Controlled potential electrolysis confirmed Cu II complex act as an excellent electrocatalyst to produce H 2 with a minimum faradic efficiency of 81% and TON as high as 73 during experiment over 23 h. They examined HER mechanism of complex 10 through DFT computational studies. In the proposed mechanism, initially the protonation occurs at the hydrazino nitrogen ligand. This was followed by an electrochemical step as a formation of reduced Cu I species [Cu I (HL)]. The second protonolysis occurs at the opposite hydrazine nitrogen of the ligand to yield [Cu I (H 2 L)] + . Further one-electron reduction of [Cu I (H 2 L)] + leads to the formation of the H 2 evolution illustrated in Figure 7. Hence, here it is worth to mention that the identity of metal ions at the active site affects the HER mechanism.
Professor Wang and group proposed [75] a significant homogeneous mononuclear copper electrocatalyst for H 2 production attributed to diamine-tripyridine ligand; complex 11 attains trigonal bipyramidal geometry. According to the author, this ionic copper complex [Cu(bztpen)] 2+ with a five coordinating nitrogen atom shows a Jahn-Teller effect. Electrochemical and spectroscopic studies supported that the H 2 generation reaction takes place by two successive proton-coupled reduction processes. On the experimental observations of DPV, CV, UV-vis, and 1 H-NMR spectroscopic study, the authors proposed two possible pathways: path (A), protonation takes place at the Cu I centered in the first step (Eqs. (4) and (5)), and path(B), protonation occurs at one of the nitrogen atoms of the ligand (Eqs. (6), (7), and (8)). H 2 generation reaction in path B takes place by two successive proton-coupled reduction processes. Protonation occurs at the ligand centered in the first reduction step, followed by the Cu I centered in the second step. This provides [(bztpenH)Cu II (H)] 2+ copper hydride species, which release H 2 and regenerate Cu II catalyst. Path A: According to the author's studies on the mechanism of this process, the controlled potential electrolysis of complex 11 was measured at pH 2.5 in phosphate buffer at À0.90 V, over 2 h in a glassy carbon electrode. TON 1.4 Â 10 4 mol H 2 (mol cat À1 ) cm À2 was calculated on a faradic efficiency of approximately 96%, which corresponds to a TOF of 2.0 molH 2 (mol cat À1 )s À1 cm À2 of [(bztpen)Cu](BF 4 ) 2 .
Moreover, Wang et al. [76] fabricated and examined two Cu complexes with TMPA = tris(2-pyridyl)methylamine and Cl-TMPA 1-(6-chloropyridin-2-yl)methyl-N,N-bis(pyridin-2-ylmethyl)methaneamine for photocatalytic H 2 evolution behavior. They observed both in Cu(II) complexes [Cu(TMPA)Cl]Cl (12) and [Cu(Cl-TMPA) Cl 2 ](13) that (13) is far efficient for photocatalytic H 2 production than (12), due to the presence of more labile Cl ligand with longer Cu-Cl bond length and a dangling Clsubstituted pyridyl unit in the second coordination sphere, which both contribute to a higher photocatalytic activity of complex (13). TMPA acts as a tetradentate ligand and coordinate with Cu(II) in a distorted trigonal manner; Cl-TMPA acts as a tridentate ligand coordinate to Cu(II) with two chloride ions in a distorted square pyramidal manner, leaving one Cl-substituted pyridyl group in the second coordination sphere structure which is given in Table 1. ESI-Ms data favor the formation of Cu-hydride intermediate for hydrogen evolution. The authors investigated the photocatalytic H 2 production activities in the presence of a multicomponent [Ir(ppy) 2 (dtbpy)]Cl (ppy = 2-phenylpyridine, dtbpy = 4,4 0 -di-tert-butyl-2,2 0 -bipyridine) and triethylamine (TEA) photosystems as sacrificial reductant (SR) under optimal condition upon 6 h of irradiation of UV-visible light, the turnover number (TON) of which is calculated as 6108 for complex (12) and 10,014 for complex (13).
Based on the control potential electrolysis experimental data, the authors proposed photocatalytic hydrogen evolution mechanism. In the first step, excited PS system takes out one electron from TEA and donates to Cu II center of complex (13). The protonated Cl-substituted pyridyl unit accepts that electron and kicks out the Cu-Cl center for the dissociation of Cl ligand which is substituted at the apical position which is more labile (longest bond length Cu-Cl). After that, the Cu I species accept one e À and one H + from the reduced Cl-substituted pyridinium moiety; Cu II -H center is formed as a key intermediate which lead to H 2 evolution. This executive mechanism provides us guidelines to design more efficient Cu-based catalysts for WRCs in the near future (Figure 8).

Ni electrocatalysts for HER
Professor Richard Eisenberg and coworker [77] synthesized a sequence of nickel bis(chelate) complexes; all complexes attained square planar geometry and examined photocatalytic as well as electrocatalytic behavior for hydrogen evolution.
Fluorescein (Fl) as the photosensitizer along with triethanolamine (TEOA) as the sacrificial electron donor was used in water under basic medium (pH = 9.8). Bis (chelate) complexes (14)(15)(16)(17) contain bdt(bisdithiolate) and their derivatives having S, O, or N as donors for coordination to the Ni center. The photochemical study reveals that only complexes 15 and 17 exhibited similar activity of hydrogen production in terms of TON (6000 mol of H 2 per mole of catalyst in 100 h). In contrast, the TON for the sample complex 16 was much lower ($900). Complex 14 was observed to be inactive for hydrogen generation. To understand the better significant result, the authors pursued electrochemical experiments under a fixed potential to examine the catalytic activity of complexes. In the absence of acid, both monoanionic complexes 14 and 17 exhibit only one reversible redox couple at À0.56 and À0.45 V, respectively, which is attributed to the [NiL 2 ] À /[NiL 2 ] 2À ligand-based reductions. The neutral complexes 15 and 16 exhibit two reversible reduction waves at À0.11 and À0.94 V and at À0.89 and À1.53 V, respectively. However, on increasing the concentration of acetic acid to these solutions, more negative catalytic waves were observed in cyclic voltammetry study. Complex 14 shows much more negative reduction potential (À2.25) which suggested this system is inactive for H 2 generation (as we discussed earlier). As is the case for complex 14, complex 16 exhibits a catalytic wave potential at À2.03 V which showed poor activity for H 2 generation as a consequence of not favorable electron transfer step from Fl À to the catalyst. Moreover, complexes 15 and 17 show activity for light-driven H 2 generation; these two complexes display electrocatalytic wave potential at significantly less negative at À1.64 and À1.62 V, respectively.

Concluding remarks and future scope
Here we present a recent development of molecular catalysts toward clean and renewable fuels using earth-abundant metals. We have highlighted a series of Co-, Ni-, Cu-, Zn-based complexes for HER. We have recapitulated the fundamental principles of hydrogen and oxygen evolution reactions with molecular complexes. The designing and fabrication of the molecular complexes with redox-active ligands have been discussed in details; HER activity of the complexes strongly dependent on redox-active ligands as well the central metal ions are discussed in detail. A mechanistic approach and transfer of electron and proton during the homogeneous electrocatalyst and photocatalysts cycle are given in point. Although reasonable progress has been made in the development of metal complexes based electrocatalysts and chromospheres for photocatalytic hydrogen production, still several issues exist which need further improvement: (i) some photocatalytic systems suffer from low activities and short life times which is manifested in the instability of catalytic systems and so concern on the systems with modest water splitting activity and poor stability of the complexes. (ii) most of the complexes are not soluble in water leading to the use of organic solvent or mixture of organicwater solvent. From the future prospective, it is required to develop redox-active ligands with substituted functional group to increase the solubility of complexes in water. More experimental, spectroscopic, magnetic, and theoretical investigations is still needed to be carried out in order to understand the ligand-and metal-centered electron transfer processes. (iii) In addition, the overpotential requirements for most of the organic ligands are still very high, a chelating ligands giving much lower thermodynamic potentials and much smaller oxidation potential that should be utilized in future. (iv) In the regard of future growth in this field, with the need to design molecular complexes that can be immobilized on the surface of the electrode, for this purpose addition of suitable functional group in the ligand is necessity. These complexes can also be supported by the development of surface of the solid photocatalyst, like TiO 2 , BiVO 4 , etc. to demonstrate efficient photoelectrochemical cell.