Detection of Underground Water by Using GPR

Water is the human vital requirement for life; in these days, decreasing of the fresh water increases the importance of the aquifer water. However, Upper Egypt is higher than north Egypt, so the water map continually changes daily, and the aquifer water is deeper than 10 m. The ground penetrating radar (GPR) system is used for underground water detection. GPR is a promising technology to detect and identify aquifer water or nonmetallic mines. One of the most serious components for the performance of GPR is the antenna system. The technology of the remote sensing and radar is rapidly developing, and it has led to the ultra-wideband electronic systems. All of these factors, such as miniaturized, low cost, possible compromise solution between depth and resolution, scanning in real time, easy to interpret, and decreased the false alarm, are important in designing the ground penetrating system. The electrical properties of the sand and fresh water layers are investigated using laboratory measurement and EM simulation. Different types of antenna may be used in GPR to operate over a frequency range for different penetration depth. Frequency-modulated continuous wave is also used for GPR and for through-the-wall applications. However, most of these kinds of antennas are limited by their large volume for certain applications. Therefore, a compact Vivaldi antenna with EBG and a compact planar printed quasi-Yagi antenna with meandered ground plane are designed to fulfill all above requirement.


Introduction
After the year 2002, ultra-wideband (UWB) systems have gained popularity mainly when the US Department of Federal Communications Commission (FCC) allocated a license-free spectrum for industrial and scientific purposes. FCC is doing the greatest step in opening new doors of researches for UWB in the field of wireless communications and microwave imaging [1,2]. UWB device is defined as any device operating in absolute bandwidth greater than 500 MHz or fractional bandwidth greater than 0.2 of central frequency [3]. The frequency band ranges of UWB extended from 3.1 to 10.6 GHz that have expected the applications in the fields of wireless body area networks (WBAN), wireless local area networks (WLAN), wireless interoperability for microwave access (WiMAX), wireless personal area networks (WPAN), and ground-penetrating radar (GPR) technology where wide bandwidth is required [4]. GPR is the major applications of UWB technology, which

GPR system
Egypt desert water, land mines, and Egyptian ancient mummy detection are an important, and yet challenging problem remains to be solved and is a matter of concern for both civilian groups and military. Water depth, quantity, and volume are different from location to another, and landmines have huge variety in use with various sizes and materials. They are mostly designed in a circular, rectangular, butterfly, or cylindrical shapes as V69, PSM-1, Hamdy, and Mon 200 with dimensions 13, 7.6, 21, and 43 cm, respectively. On the one hand, the electrical properties of water purity are changed due to water quantities and mineral contained; on the other hand, the electrical properties of the mummy are varying according to biological materials involved as tissues, bones, scapula, and femur, respectively [23]. The average effective dielectric constant is equal to 6.5 and dielectric loss equal to 15 [24]. DOI: http://dx.doi.org /10.5772/intechopen.83594 Groundwater is a hidden natural resource. It is found in different proportions, in various rock types, and at various depths of ground surface. Previously, in the past, when there is no visible flow of water along the rivers or lakes, people used to dig small pits, in the river alluvium, then collect the groundwater coming through seepage to use in different purposes and for meeting the domestic needs. As well as the people of mountainous area, springs are the outcome of seepage from any groundwater system [25,26].
More than 60% of the global population thrives by using only the groundwater resources. The groundwater, which was existing at shallow depths in the open wells, has gone deep due to overexploitation. Exploring these water sources becomes a challenging task to geoscientists [27][28][29].
As the signal of the GPR is required to propagate through inhomogeneous media, the efficiency of the antenna should be taken into account. Thus, in order to enhance the efficiency, a compact shape of Vivaldi is designed [7]. The compactness in the shape of antenna is achieved by using two Vivaldi surface shapes with the same feeding network. Frequency-modulated continuous wave (FMCW) is another type than pulse wave also used for GPR and for through-the-wall applications. FMCW systems are transmitting a repetitive waveform with increasing or decreasing frequency [21]. UWB-FMCW systems require a linear sweep, which may be difficult to create. Lower-frequency signals are required to penetrate the ground effectively as the penetration depth decreases with increasing frequencies.
GPR radar could be used for soil with different electrical properties to detect water underground [30,31]. However, a broadband signal with good resolving power is required. Thus, the GPR antenna should operate on lower frequency and should have a very wide bandwidth. Also, the UWB antenna applied to communication system with high gain is highly desired [32].

Compact ultra-wideband (UWB) Vivaldi antenna
The main object of this section is the detection of water. A compact novel shape of Vivaldi antenna as shown in Figure 1 with dimensions of 0.17λ × 0.16λ × 0.013λ is proposed in this section [6].
A comparative study was undertaken as shown in Table 1 for different Vivaldi antenna that are used of GPR application in the same interesting operating frequencies [8][9][10][11] to show that the proposed antenna gives compact size with higher gain from 250 MHz up to 10 GHz. There are a number of techniques used for improving the parameters of printed antennas with different feeding techniques. These techniques include electromagnetic bandgap (EBG), metamaterial, and defected ground structure (DGS). EBG structure has gained popularity among all the techniques reported for enhancing the parameters due to its simple structural design. The periodical shapes are etched as square, mushroom, and circular shapes in the radiator or ground plane to achieve inductive and capacitive load to create band-stop characteristics and to suppress higher mode harmonics and mutual coupling.
The basic concepts, working principles, and equivalent models of the different shapes of electromagnetic bandgap structure (EBG) are presented [36]. EBG has been used in the design of the Vivaldi antennas for improving the bandwidth and gain of proposed antenna and suppressing the higher harmonics mode and mutual coupling between adjacent elements. In addition, the proposed antenna crosspolarization is improved for the radiation characteristics [6].

Vivaldi antenna geometry and principle theory
A relatively large number of published UWB Vivaldi antennas consist of a feed line and exponential ground plane. Our proposed antenna starts as shown in Figure 2(a) from one layer of FR4 low-cost substrate with conventional exponential Vivaldi tapered slot line shape using empirical Eq.(1) [4]: where x and y are the axes of the inner and outer exponential to improve the impedance bandwidth. The first step is without any slot, Figure 2(a), the second with circular EBG-etched slot on the edge of exponential tapered slot.
The symmetrical circular electromagnetic bandgap structure (EBG) slots are etched to increase the antenna bandwidth as shown in Figure 2(b). The modified version from the first one is obtained by slotting the two arms of the Vivaldi antenna.
To improve the bandwidth of the Vivaldi antenna, symmetrical semicircular slots are etched to increase the antenna bandwidth as shown in Figure 2  Finally, dual FR4 substrates printed with Vivaldi ground plane with the same feeding line are used. The final geometry of the proposed antenna design with ground plane and feeding network is shown in Figure 3. This design is used to investigate a dual substrate layer of Vivaldi ground plane antenna as shown in Figure 3(a) with the same feeding network as shown in Figure 3(b). Proposed Vivaldi antenna consists of two layers from the dielectric sheet, the feeding line is sandwiched between them, and the two layers of metallic Vivaldi are mounted on

Antenna simulation and measured results
The reflection coefficients of the antenna versus frequency for the four-step design of Vivaldi antennas in frequency range from 0.25 to 10 GHz are shown in Figure 4(a), and the zooming range from 0.25 to 2 GHz is shown in Figure 4(b). The final antenna design achieves improvement in antenna impedance matching all over the band. The dimensions of the proposed antennas are shown in Table 2.
The surface current density distributions of the compact Vivaldi antenna is shown in Figure 5 at different resonant frequencies 0.4, 0.5, 0.75, 1.5, 1.75, and 2 GHz. The current distribution of the proposed antenna is studied to verify the operation of the proposed Vivaldi antenna. The exponential edge is responsible for the fundamental resonant frequency of the proposed antenna at 1.75 GHz as shown in Figure 5. The semicircular slots are etched to create the frequencies at 0.5 and 0.75 GHz. By adding stubs with different lengths, they are affecting the resonance from 1 to 2 GHz. The highest magnitude of current (red) is related to the corresponding radiating element. The simulated antenna gain of single and dual substrate is shown in Figure 6(a). The gain gives better performance by using dual substrate layer, and it increases from 8 to 17 dBi in average over the operating band from 0.2 to 2 GHz. The average radiation efficiency is around 80% over the operating band for dual substrate, while its value is 50% for single substrate as shown in Figure 6(b).
To validate the simulated results of the proposed antennas with single and dual substrate, they are fabricated by using printed circuit board (photolithographic)  technology and measured by using Agilent vector network analyzer technologies "Field Fox" Microwave Analyzer N9918A 26.5 GHz. Figure 7 shows the photo of the fabricated antenna, feeding line, and Vivaldi antenna with dual substrate. The comparison between the measured and simulated results has been performed for the proposed Vivaldi antenna with single substrate that indicates good agreement.      Figure 9. Figure 9(a) shows the whole range from 0.2 to 10 GHz, while Figure 9(b) shows the zoom-operating range from 0.2 to 2 GHz. One can notice that there is a slight difference between the measured and simulated results of the reflection coefficient due to soldering of feeding launcher and fabrication tolerances.       Figure 10 shows the three-dimensional radiation patterns of the proposed dual substrate Vivaldi antenna at different operating frequencies within the operating band at 0.5, 1, 1.5, and 2 GHz. The radiation patterns correspond to the axes shown in Figure 1. In the antenna, the radiator and the ground plane are participating to radiation. End-fire radiation pattern is an important requirement for ultrawideband GPR application system. At lower frequencies of operation, the pattern resembles a conventional dipole antenna, but at higher end of the UWB spectrum, a few ripples are observed which is due to higher-order modes.

Printed quasi-Yagi antenna with size reduction for water detection
Nowadays, quasi-Yagi printed antenna is extensively used in modern radar systems due to some advantages as high directivity, good radiation efficiency, affordable, low profile, and easy fabrication [33][34][35]37]. However, the disadvantage of these antennas is narrow bandwidth, which achieves about 10%. So, the microstrip-fed quasi-Yagi antenna was initially introduced in 1991 [38] to improve the bandwidth of planar printed quasi-Yagi antennas, and many designs have been reported in [39]. A quasi-Yagi antenna based on microstrip-to-slot-line transition structure was presented in [40]. Modified wideband microstrip-to-coplanar strip-line (CPS) balun was used in quasi-Yagi antenna designs for increasing the antenna bandwidth [41]. Approximately 48 and 38.3% bandwidths were achieved by using the microstrip-to-coplanar strip-line transition structures in [42] and [43], respectively. However, the antenna bandwidths are still restricted by the delay line used in the balun structures. Coplanar waveguide feeding or ultra-wideband balun was presented to improve the bandwidth in some designs [44]. A broad bandwidth of 44% was obtained in [45]. However, the asymmetric nature of the printed quasi-Yagi antenna deteriorates the unidirectional radiation patterns. An ultra-wide band balun feeding structure in which the balun was realized via holes was used in quasi-Yagi antenna for wideband in [46]. Slot and CPS-fed feeding structures were also used in planar printed quasi-Yagi antenna to increase the bandwidth. The maximum available bandwidth of these techniques is about 55%. To improve the bandwidth of quasi-Yagi antenna by modifying the driver to a tapered driver or bowtie driver, rapid developing technology of remote sensing and radar has led to the ultra-wide band (UWB) electronic systems. Figure 12 shows the geometric structure and parameters of the proposed planar quasi-Yagi antenna. This antenna is printed on commercial thick FR4 substrate and a thickness of 9.5 mm. The antenna consists of a microstrip-line-to-slot-line transition structure, a meandered driver T-shaped dipole and two meandered parasitic strips on top layer. The feeding system is printed on the other substrate side with lengths L f and S D with a circular resonator. The circular resonator is used to match the input impedance of the antenna to a 50 Ω feeding line. The dimension of the substrate width and length are 72 × 70 cm 2 . For matching the antenna, a λ / 4 slot line ended with a circular slot of diameter L D is used.

Antenna design and geometry
The traditional printed quasi-Yagi antenna started to resonate from 90 MHz as shown in Figure 13(a). Folded stub ground plane and driven dipole that is etched in order to reduce the size of the printed quasi-Yagi antenna, as shown in Figure 13(b), are employed. The ground plane width and the driver dipole length are equal. The antenna shown in Figure 13(b) has 80 MHz as the lowest frequency. Since the ground plane has reduced size, the bandwidth of the antenna is reduced. A driver meander dipole is etched to increase the electrical size of the antenna (Figure 13(c)). The antenna started to operate from 62.5 to 185 MHz. Two meandered stubs are symmetrically extended from its ground plane as shown in Figure 13(d). The reflection coefficients |S11| of the antenna design procedure are shown in Figure 14.
As shown, the antenna consists of a circular balun feeding which takes the form of a curved microstrip line step transition, in addition to a printed dipole, a ground plane, and two parasitic strips. The larger dipole is located at a distance S away from the ground plane which has a greater length than the larger dipole itself, so it can act  Simulated |S 11 | of the design steps as shown in Figure 11 [37].  as a reflector. On the second size of the substrate, the two dipoles are located, their line length is 2.6 cm, and the two parasitic spacing was optimized using the readingmade software package HFSS ver.14 in order to improve the antenna performance which means that it has a wide bandwidth, stable radiation, moderate gain, and high front-to-back ratio.
In quasi-Yagi antenna design, metallic strip is always used as a director. To improve the directivity and impedance matching in the high-frequency band, the two metallic strips are used. The simulated surface current distributions of the proposed antenna at 50, 100, and 150 MHz are shown in Figure 15. The directors have weak surface current as shown in Figure 15, while the two parasitic strips have a large magnitude of surface current at 50 MHz. the largest value of surface current at resonant 100 MHz takes place at larger parasitic strip and the driven dipole. At 150 MHz, the current concentrates on the meandered driven dipole. Compared to Figure 15, the surface currents on the metallic strips are enhanced, which means that the effects of the parasitic strips as directors improved the antenna performance at the high-frequency band.

Antenna parameter study
The antenna structure was optimized to operate at 100 MHz center frequency. The reflection coefficient against frequency for different values of L 1 is shown in Figure 16(a). As the value of L 1 is increased (in steps from 40 to 55 cm), the resonance frequency decreased. At L 1 = 50 cm, the antenna provides the largest beamwidth. One can say that the resonant frequency of the lower band is mainly determined by the length of the larger strip. The dipole in this antenna acts as director of quasi-Yagi antenna. Also, simulation was done to see the effect of L 2 on the antenna bandwidth. Figure 16(b) shows S 11 against frequency for different values of L 2 , which shows that as L 2 increased from 20 to 35 cm, the highest frequency almost did not change, while the lower resonance (50 MHz) slightly changed. When the ground plane circular slot L D was changed from 4 to 5.5 cm, impedance matching was affected, while the lower and higher frequency did not change (Figure 17(a)). One can conclude that the diameter of the slot affects the feeding impedance. The effect of the feeding length L f was studied as shown in Figure 17(b). L f was varied from 15 to 16.5 cm which caused noticeable changes in the operating frequency band and the value of the reflection coefficient. The length L f highly affects the impedance matching, and the optimized length of the feeding is 16 cm. Figure 18(a) shows the reflection coefficient of the antenna as a function of the spacing between the driver and director (T and T 1 ).
Increments of the spacing decreased the coupling effect between the parasitic element and the dipole induced significant changes in the reflection coefficient in the operating band region from 50 to 150 MHz, but negligible changes occur in the bandwidth. In the high-frequency region of 100 MHz band, the antenna performance is affected mainly by the spacing between the driver and the director. The quasi-Yagi antenna and the T-dipole were designed to operate at 50 and 150 MHz, which shows that a suitable choice of this spacing is very important for the wideband operation of the proposed antenna.
The reflection coefficient S 11 against frequency is shown in Figure 19 for different values of the parameter D (balun circle) and S D (length from the feeding). The lower resonance and impedance matching are varied as D increases from 4 to

Ground-penetrating radar antenna system
FMCW GPR system is used for the detection of underground water in the frequency range from 50 to 150 MHz. Figure 20(a) shows the radar system which requires a high-gain antenna to obtain acceptable scanning resolution. We used laboratory measurement and EM simulation in order to investigate the electrical and physical properties of the sand and fresh water. The simulated parameters depend on the Debye dispersive model inherent in HFSS software package. Figure 20(b) shows the study of the ground effect on the radiation characteristics of the antenna S11 projection. The distance K between the antenna and the ground surface was increased from up to 100 cm. The volume of the sand layer was 300 × 200 × 200 cm 3 . Figure 21 shows the reflection with and without the sand layer. It was found that in order to keep S 11 very close from the case of free space, K should not be less than 50 cm. Figure 22 shows both the gain and radiation efficiency. It is clear that the gain was increased by about 1.5 dBi compared to the case of free space, which may be attributed to the increase in directivity at certain frequencies, while it remains unchanged in other frequencies.
The antenna radiation efficiency, as indicated from Figure 22, is reduced. The threedimension radiation pattern of the proposed antenna in both cases is also studied at three different resonant frequencies 50, 100, and 150 MHz, respectively, as shown in Table 3, while the 2D radiation patterns at xy-plane (EФ, Eθ) at Ф = 0° and yz-plane        Table 4 at the same frequencies.
The two-dimensional radiation patterns at 50, 100, and 150 MHz with and without sand are platen in Table 4. A slight change took place in the E-plane and H-plane radiation patterns keeping good directivity within the whole frequency band. The bock lobes are below −5 dB. Deterioration takes place in the H-plan (YZ plane) as the frequency increases especially in the high-frequency bands (e.g., 500 MHz).

Fabrication and measurements
A photolithographic technique on FR4 substrate with 100 μm copper thickness was used to realize the proposed antenna. A 50 Ω SMA launcher was used as a transition between the microstrip antenna and the coaxial line, which was not included in the simulation process. Rohde and Schwarz ZVA67 VNA was used to measure S11. The antenna gain and radiation efficiency are also tested as shown in Figure 23 in both cases namely free space and in the presence of sand layer. The antenna gain is also tested as shown in Figure 23 in both cases namely free space and in the presence of sand layer. The proposed antenna performance is investigated with and without sand layer as shown in Figure 20(a). The sufficient distance that keeps the antenna reflection coefficient near from free space is almost about 50 cm as shown in Figure 20(b). Figure 23 shows that the antenna radiation efficiency is increased at present of sand layer by 5%. While the antenna gain is reduced by about 1.5 dBi in the present of sand layer. The gain in the present of sand layer increases at certain resonant frequency due to increase in directivity and has value less than free space on the other resonant frequencies. The optimized antenna reflection coefficient is measured, and there is a good agreement with the simulated results. The measured bandwidth extends from 56 to 150 MHz for the −6 dB reflection coefficient, while the simulated bandwidth extends from 45 to 140 MHz. This bandwidth completely covers the specification for operation.
The slight difference between the measured and simulated reflection coefficient could be from misalignment between curved microstrip line and the circular slot of the balun and effect of the SMA connector, in addition to some fabrication tolerances.

Conclusion
The importance of aquifer water increased these days after decreasing the fresh water. A precise approach for the detection of buried nonmetallic objects is groundpenetrating radar (GPR). It should be importance of aquifer water increased these days after decreasing the freshwater. A precise approach for the detection of buried nonmetallic objects is ground penetrating radar (GPR). A novel, miniaturized, and low-cost antennas, which compromise between depth and resolution for different applications, are highly needed. This requires hundreds of conducting research activities in this area. However, although GPR has shown some promising results, the complexity of the problem requires certain challenges on the operation of GPR systems. One of the most serious hardware components for the performance of ground-penetrating radar (GPR) is the antenna system. First, a new compact Vivaldi antenna is designed to achieve ultra-wideband extending from 0.4 to 10 GHz and high average gain of about 17 dBi with average radiation efficiency of about 80%. The proposed antenna consists of dual exponential Vivaldi shapes on both dielectric substrates with the same feeding network. The GPR results in frequency range extending from 0.4 to 2 GHz of the water detection have also been investigated under certain system parameters. Second, ultra-wideband printed quasi-Yagi antenna has been introduced. The proposed antenna has the advantage of simple single feed structure which consists of a circulator balun with a microstrip line and a circulator slot. The antenna bandwidth extends from 47 to 150 MHz based on −6 dB reflection coefficient. The gains at the upper and lower bands are 3.5 and 6.5 dBi. It should be noted that the proposed antenna has the advantage of simple structure and stable end-fire radiation pattern, which makes it widely used in ground-penetrating radar. The average simulated gain in this band is about 5 dBi. At the same time, this antenna possesses low profile and miniaturization characteristics. Furthermore, the wide beamwidth and high gain can promise the antenna to be widely applied in many communication systems.