Fiber Laser for Phase-Sensitive Optical Time-Domain Reflectometry

We have designed a new fiber laser configuration with an injection-locked DFB laser applicable for phase-sensitive optical time-domain reflectometry. A low-loss fiber optical ring resonator (FORR) is used as a high finesse filter for the self-injection locking of the DFB (IL-DFB) laser. By varying the FORR fidelity, we have compared the DFB laser locking with FORR operating in the under-coupled, critically coupled, and over-coupled regimes. The critical coupling provides better frequency locking and superior narrowing of the laser linewidth. We have demonstrated that the locked DFB laser generates a single-frequency radiation with a linewidth less than 2.5 kHz if the FORR operates in the critically coupled regime. We have employed new IL-DFB laser configuration operating in the critical coupling regime for detection and localization of the perturbations in phase-sensitive OTDR system. The locked DFB laser with a narrow linewidth provides reliable long-distance monitoring of the perturbations measured through the moving differential processing algorithm. The IL-DFB laser delivers accurate localization of the vibrations with a frequency as low as ~50 Hz at a distance of 9270 m providing the same signal-to-noise ratio that is achievable with an expensive ultra-narrow linewidth OEwaves laser (OE4020–155000-PA-00).

Such optical sensor analyzer operates as a conventional OTDR, where a light pulse is injected into the optical fiber and Rayleigh backscattering radiation originating from the natural refractive index inhomogeneities frozen in the fiber core is recorded as timedependent traces. However, in contrast to the conventional OTDR utilizing low coherence laser sources and hence based on recording of Rayleigh backscattering intensity, the w-OTDR systems require highly coherent lasers with a coherence length exceeding the pulse duration and employ a difference between consequent time-dependent traces as a readout signal. For proper operation of w-OTDR systems, the allowed optical frequency shift between two neighboring pulses should be low enough to keep Rayleigh backscattering interference pattern recorded as a result of pulse reflections from multiple scattering fiber centers unchangeable. Under these conditions, two consecutive traces recorded in an undisturbed fiber are identical. Meanwhile, any change in geometry of the frozen distribution of the refractive index in the fiber core caused by stress, strain, or temperature variations applied to some fiber points affects the difference between successive traces and, therefore, can be detected and localized with w-OTDR systems [19][20][21][22]. Typically for long-distance measurements, a coherent laser source with a few kHz linewidth and frequency drift less than 1 MHz/min is required [2]. It is well known that self-injection locking of conventional telecom DFB lasers could significantly improve their spectral performance [23][24][25][26][27][28][29][30][31][32][33][34]. In our previous works, we have demonstrated substantial narrowing of the laser linewidth due to a spectrally selective feedback realized with FORR built from low-cost standard fiber telecom components [35][36][37]. To provide the DFB laser locking, a part of the optical radiation emitted by the DFB laser is passed through the filtering in a fiber ring resonator and returned into the laser cavity. This low-cost all-fiber solution allows achieving the laser linewidth as narrow as 500 Hz [36].
In this chapter, we demonstrate application of the DFB laser locked through a fiber ring cavity for w-OTDR systems. In particular, we show that the proposed laser solution in combination with the moving differential processing algorithm enables accurate detection and localization of vibrations applied to the sensing fiber at a distance up to 10 km. Figure 1 shows the experimental configuration of the DFB laser locked through a fiber optic ring resonator (FORR). The MITSUBISHI FU-68PDF-V520M27B DFB laser with a built-in optical isolator operates a linewidth of~2 MHz at the wavelength of~1534.85 nm. The output DFB laser radiation is passed through an optical circulator (OC), optical coupler (C1), and polarization controller (PC1) and then introduced into a fiber optic ring resonator. The FORR consists of a variable ratio coupler VRC, 95/5 coupler C2 and comprises~4 m length of a standard SMF-28 fiber. The operation of FORR is similar to the Fabry-Perot interferometer with the reflected power detected in port B and transmitted power directed to the coupler C3 [20]. The radiation at the port A is used as an output of the injection-locked DFB (IL-DFB) laser, while port B and C are connected to detectors for the monitoring of the reflected and transmitted powers, respectively. Optical isolators prevent reflections from the fiber ends that potentially could affect the DFB laser behavior. The polarization controller (PC2) and the optical switcher (OS) are used to adjust the feedback strength and activate or deactivate the optical feedback loop that returns transmitted through the FORR power back into the DFB laser cavity.

Experimental results and discussion
Once the DFB laser frequency gets a resonance with the FORR, the DFB laser is locked in frequency to one of the FORR frequency modes. This effect could be observed as a suppression of the temporal power fluctuations recorded at ports C and B. Figure 2 shows typical oscilloscope traces of transmitted and reflected powers recorded at ports C and B, respectively. Single   frequency regime is observed during some time intervals that are interrupted by short-time mode hopping events. The frequency drift during the stable time interval strongly depends on environmental conditions and can be less than 1-2 MHz/min, if the FORR is placed in an isolation box used for environmental protection.
Stabilization of the laser operation is accompanied by stabilization of the polarization state of the locked DFB laser radiation recorded at the port A and the transmitted power recorded at the port C (see Figure 3). However, during the mode hopping, the polarization state can be changed. In our previous work, we have reported two possible regimes of mode hopping [35].
The first regime, we have attributed to the hopping between FORR modes of nearest orders, but of the same polarization state, and the second one to the hopping between orthogonal polarizations modes of the same order. These two regimes have significantly different time which the system takes to recover steady-state operation after the mode hopping event. In the first most common regime, the recovery time is typically~5 ms, but in the second regime, the typical recovery time is significantly less and equal to~100 μs [35].
The locking performance strongly depends on the parameters of the VRC coupler used in the FORR. The coupling regime is defined by a relation between the VRC coupling coefficient k 1 and the total losses inside the cavity α [38]: where the power transmission coefficient α includes all losses inside the fiber loop and γ 1 is the intensity loss in the variable ratio coupler. Figure 4 shows the normalized reflected power versus the coupling coefficient k 1 at port B. In the critical coupling regime, the reflected power reaches the minimum, and therefore, all nearby input power are transmitted through the FORR (see Figure 5). For that reason, the critical coupling provides higher feedback strength leading to better locking. Let us stress out that for the DFB laser locked at the resonance frequency of the FORR, the transmitted and reflected powers from FORR are in good agreement with the theoretical estimations.
The finesse of the resonance peak of the FORR is defined as a ratio of the FORR intermode interval to the spectral peak width: where FSR = c/nL ≈ 50 MHz is the free spectral range of the FORR and Δf is the full-width at half-maximum (FWHM) of the feedback loop transmission peak.  For the FORR configuration with an additional coupler C2, Δf could be found following the same procedure as it is described in Ref. 26 for a simple optical ring resonator. For our resonator, the FWHM of the cavity mode can be estimated as [37]: In the critical coupling regime at k 1 = 0.08, Eq. (3) gives Δf = 0.77 MHz and the finesse F = 65.8.
The finesse of the resonator strongly depends on the total cavity losses and the coupling coefficient. The finesse is higher for smaller losses and lower coupling coefficients (see Figure 6).
The delayed self-heterodyne spectra of the IL-DFB laser measured with unbalanced Mach-Zehnder interferometer [39] during the time intervals of stable laser operation at the critical coupling regime are shown in Figure 7. The Mach-Zehnder interferometer comprises 35 km of the delay fiber line in one arm and 20 MHz phase modulator in the other. The beat signal of two interferometer arms is detected by 125 MHz photodiode and RF spectrum analyzer. One can see that the DFB laser linewidth Δν decreases from approximately 2 MHz for a free running laser to 2.4 kHz for the IL-DFB laser operating in critical coupling regime.
Assuming the Lorentzian shape of the laser line, the laser coherence length L c [40] is described as: where c is the speed of the light in vacuum, N eff is the effective group refraction index in the sensing fiber equal to 1.468 [41], and Δν is the laser linewidth.
Therefore, the coherence length is increased from approximately 26 m for a free running DFB laser up to 27.2 km for the IL-DFB laser operating in the critical coupling regime.     Thus, the critical coupling provides the best IL-DFB laser stability and narrowest linewidth making the laser applicable in w-OTDR systems.
The configuration of the w-OTDR system with IL-DFB laser operating in the critical coupling regime is shown in Figure 9. The output radiation of the IL-DBF laser is amplified by an EDFA up to 23 mW and passes through a bandpass filter (BPF) to filter out spontaneous emission noise. Since a low-frequency perturbation causes very small modification of the Rayleigh scattering traces, a simple calculation of the differences between two neighboring successive traces is not enough to localize the perturbed fiber segment. Figure 10 shows superposition of the absolute values of differences between all neighboring successive traces. One can see that the signal obtained for the distance of perturbations is the same as for any other positions.
However, the signal-to-noise ratio can be significantly improved with applying a special averaging procedure. For these purposes, we have processed the storage traces by employing three-step algorithm which is similar to moving differential method [19].
First, we determine the partial sums by averaging of N consequent traces. Each next partial sum is shifted by a number m of traces from the previous one. Then, we calculate the absolute value of the differences between every consequent partial sum.
The last step of the algorithm includes an analysis of the superposition of the absolute values for all differences.  Figure 11 shows the superposition of all differences for N = 75 and m = 10. The highest peak denotes the point of the perturbation at 9270 m along the fiber under test. The signal peak exceeds the maximum of the noise value in 1.6 times and the average value of the noise approximately by 9 dB. Let us stress out that with the unlocked DFB laser, we never register the perturbation even at distances less than 0.1 km.
It is experimentally demonstrated that the relation between the signal and average value of the noise strongly depends on the shift between the averaging data arrays. However, a choice of   the number of averaging not so strongly affects the signal-to-noise ratio and could be selected arbitrary within the interval between 40 and 120. Figure 12 shows superposition of the absolute values of differences between the averaged traces for the shift m = 23 and averaging number N = 75.
The signal peak exceeds the maximum of the noise value in 2.1 times and the average noise value approximately by 10 dB. A number of the performed experiments allow us to conclude that in our experimental conditions, the maximum of the signal-to-noise ratio is achieved with the shift m approximately equal to 20.
The obtained value of the signal-to-noise ratio allows correct localization of the perturbations with the IL-DFB laser system at distances of about 10 km and resolution of around 10-15 m but does not allow comparing a capacity of the proposed solution with commercially available techniques.
In order to fulfill this gap, we have performed the same measurements, under the same experimental conditions, but utilizing a commercially available ultra-narrow linewidth (~300 Hz) laser OEwaves laser OE4020-155000-PA-00. Figure 14 shows the superposition of the subtractions of averaged traces for the measurements utilizing OEwaves laser for the shift m = 23 and averaging number N = 75. The signal peak at the distance of~9270 m exceeds the highest noise signal in about 2.25 times that is nearly the same result as obtained with our IL-DFB laser.

Conclusion
We have employed IL-DFB laser configuration at the critical coupling regime for detection and localization of the perturbations by w-OTDR system.
At the critical coupling regime, the laser power is practically totally accumulated inside the cavity providing strong feedback for laser locking and resulting in the best laser stability and  Fiber Laser for Phase-Sensitive Optical Time-Domain Reflectometry http://dx.doi.org/10.5772/intechopen.72553 significant narrowing of the laser generation spectrum. The locked DFB laser with the linewidth of about 2.4 kHz provides the long-distance measurements of the perturbations as the moving differential processing algorithm is applied. The IL-DFB laser delivers accurate localization of vibrations at the frequency as low as low 50 Hz at the distance of~9270 m with the same signal-to-noise ratio that is achieved with an expensive ultra-narrow linewidth laser OEwaves laser OE4020-155000-PA-00.
We believe that proposed solution can be useful for applications in cost-effective w-OTDR system for the measurement of the perturbations at distances up to ten kilometers.