Vibration Suppression Controller of Multi-Mass Resonance System Using Fuzzy Controller

Vibration suppression control of the mechanical system is a very important technology for realizing high precision, high speed response and energy saving. In general, the mechanical system is modeled with a multi-mass resonance system, and vibration suppression control is applied. This chapter presents a novel controller design method for the speed control system to suppress the resonance vibration of two-mass resonance system and three-mass resonance system. The target systems are constructed by a motor, finite rigid shafts, and loads. The control system consists of a speed fuzzy controller and a proportional-integral (PI) current controller to realize precise speed and torque response. In order to implement the experimental system, the system is treated as the digital control. This chapter also utilizes a differential evolution (DE) to determine five optimal controller parameters (three scaling factors of the fuzzy controller and two controller gains of PI current controller. Finally, this chapter verified the effectiveness to suppress the resonance vibrations and the robustness of the proposed method by the computer simulations and the experiments by using the test experimental setup.


Introduction
Recently, motor drive system, which consists of several motors, shafts, gears, and loads, is widely utilized in industrial fields. These mechanical systems are made a request the highspeed response, weight reduction, miniaturization, and high precision requirements for various industrial applications.
Hence, in industrial field, the system is treated as a multi-mass resonance system, which consists of several inertial moments, torsional shafts, and gear coupling. The first-order approximation model of multi-mass resonances model is two-mass resonance model. For instance, several control methods, which are PID control (Proportional plus Integral plus Derivative Control) with a resonance ratio control using the disturbance observer, coefficient diagram method (CDM), full state feedback control with the state observer, the pole placement method, fractional order PID k control, and H ∞ control method, are effective to control for twomass resonance system [1][2][3]. Ikeda et al. [4] have explained the effectiveness of the controller design technique using the pole placement method for the two-mass position control system. However, the resonance system is required more high precision and high response speed control in recent years. Therefore, it is necessary to deal with a higher order model of the resonance system. For instance, the drive train of the electric vehicle is constructed the fourmass system. Likewise, the ball screw drive stage is typically four-mass system. The thermal power generation system composed of multiple turbines and generators is modeled as twelvemass resonance system. Thus, several vibration suppression control methods on three-mass resonance system or more have been proposed [5,6]. Here, modified-IPD speed controller using Taguchi Method has been proposed in Refs. [7,8].
Meanwhile, the state equations of the controlled object and its parameters are required to design the control systems. Refs. [9,10] previously proposed a controller gain tuning method for a vibration suppression-type speed controller using fictitious reference iterative tuning (FRIT) for single-input multi-variable control objects without knowledge of the system state equations and the parameters.
In contrast, a fuzzy control system can be assumed as one method for solving these problems. A fuzzy control system using a fuzzy inference is the embodiment of non-mathematical control algorithm, which is constructed by experience and intuition. Several applications brought in the fuzzy control system to motor drive system [11][12][13][14].
This chapter proposes a vibration suppression controller by using a fuzzy inference. The control system consists of a speed fuzzy controller and a proportional-integral (PI) current controller to realize precise speed and torque response on two or three inertial resonance system. In the control system, only motor side state variables are utilized for controlling the resonance system. Additionally, this chapter treats with the proposed control system as the digital control system. Here, the proposed control system is new system that I improved to apply the control system which I already proposed for simulation model in Refs. [13,14] to experimental actual equipment.
The fuzzy controller has three scaling factors, and the PI current controller has two controller gains. In this chapter, a differential evolution algorithm (DE) is utilized the determination of these five controller parameters [13][14][15][16][17][18]. DE, which was proposed by Price and Storn, is one of the evolutionary optimization strategies. By using DE, it is easy and fast to determine the proper controller parameters.
Lastly, the validity of the controller design, the robustness, and the control effectiveness of the proposed method was verified using the simulations and the experiments by using the test experimental set up.
2. Multi-mass vibration suppression control system 2.1. 2-mass model Figure 1 shows the two-mass resonance model. The model is configured of two rigid inertial masses with a torsional shaft, where ω M , T dis , ω L , T in , J M , J L , K s , and T L denote the motor angular speed, the torsional torque, the load angular speed, the input torque, the inertia of motor, the inertia of load, the shaft torsional stiffness, and the load torque, respectively.
If all the state variables can be observed by several sensors and all the system parameters are known or identified, it is easy to construct the optimal control system. However, in general, it is difficult to measure the state variables of the load side due to constraints on scarce measurement environment and sensor installation location. Therefore, in this chapter, we use only the motor side variables. Furthermore, we contemplate for the current minor control in order to compensate torque response. Eq. (1) shows the continuous state equation of two-mass resonance model, where the viscous friction is not considered.
Eq. (2) shows the transfer function of two-mass model, which input signal is T in and output signal is ω M .
where ω r is a resonance frequency and ω a is an anti-resonance frequency. Here, we use the DC servo motor as the driving motor. Eq. (3) is the voltage equation of dc servo motor, where R a is the armature resistance, L a is the armature inductance, K e is the back-emf constant, and K 0 is the converter gains of the DC power supply. Input torque is calculated by T in = K t i a , where K t is the torque constant.   The inertia ratio R of two-mass model is given by Eq. (4), where J Mn and J Ln represent the nominal values of the motor and load inertias, respectively.

Three-mass model
Similarly to two-mass resonance model, Figure 3 reveals the three-mass model. The model consists of three rigid inertias and two shafts. Here, J c and J L are the load 1 inertia moment and the load 2 inertia moment, respectively. Furthermore, ω c , ω L , T dis1 , T dis2 , K s1 , and K s2 denote load 1 angular speed, load 2 angular speed, shaft 1 torsional torque, shaft 2 torsional torque, the shaft 1 stiffness, and the shaft 2 stiffness, respectively. Figure 2. Block diagram of two-mass resonance model. The state equation of three-mass resonance model is shown in Eq. (5). Then, Eq. (6) shows the continuous transfer function of three-mass resonance model, which input signal is T in and output signal is ω M .
In this equation, ω indicates the angular frequency, where ω r1 , ω r2 , ω a1 , and ω a2 are the resonance frequencies, and anti-resonance frequency, respectively. Then, the block diagram realized by using above equations is shown in Figure 4.

Experimental set up
This chapter confirms the effectiveness and performance of the proposed method by experiments using the experimental equipment. Figure 5 is the appearance of the experimental system constructed in this research. The twomass resonance system is simulated by utilizing the dc servo motor and the dc generator with a finite rigid coupling. The controller is realized on a digital signal processor, which calculates the PWM signal to a four-quadrant dc chopper.
The DSP board (PE-PRO/F28335 Starter Kit, Myway Plus Corp.) consists of the DSP (TMS320F28335PGFA), a digital input/output (I/O), ABZ counters for encoder signals, analogto-digital (AD) converters and digital-to-analog (DA) converters [19]. The motor and load angles and angular speeds are detected using 5000 pulses-per-revolution encoders. The current of dc servo motor is measured by the current sensor and AD converter.  The control frequency and the detection frequency of the encoder are both 1 ms, and the detection period for the current is 10 μsec. The design language used was C. Then, while considering the application of the system to specific apparatus, we constructed a digital control system that contains a discrete controller. In addition, we used MATLAB/Simulink software for the proposed off-line tuning process based on simulation and constructed the fuzzy control system as a continuous system [20]. The disturbance is added to the dc generator as the torque by using the electric load device on constant current mode. Figures 6 and 7 show the apparatus of the two-mass model and three-mass model used in the experimental set up, respectively. Figure 8 shows the experimental system configuration. For reference, the nominal parameters    Tables 1 and 2, respectively. Figure 9 shows an example of experimental result using two-mass model. These step waves are the motor and load angular speeds with direct current voltage input. Similarly, Figure 10 shows an example of experimental result using three-mass model, which are the motor and  Figure 8. Configuration of experimental system (two-mass resonance model).

Symbol
Parameter Value  load angular speeds with same above condition. In these figures, the resonance vibrations can be observed. The purpose of this research is to suppress these resonance vibrations.
3. Proposed fuzzy control system

Fuzzy speed controller
Fuzzy controller, which is executed by the fuzzy set and the fuzzy inference, can control for nonlinear systems or uncertain model. Figure 11 indicates the proposed fuzzy speed controller in this chapter. The speed controller is based on fuzzy control. The current controller is typical PI controller. Furthermore, the load side state variables are not utilized for control, where S 1 , S 2, and S 3 are the parameters to determine the scale of the membership function, which are called scaling factors or scaling coefficient. K pc and K ic are the current PI controller gains. Eq. (7) shows the transfer function of current PI controller. Additionally, this chapter uses the discrete control system. u c ðkÞ ¼ K pc þ 1 s K ic eðkÞ ð 7Þ Figure 12 is indicative of the membership function for the premise variables. This membership function is a shape of triangle with a dense center. Figure 13 indicates the membership     Then, the consequence variable is the variation width of the current input Δi ref (k). Therefore, the proposed fuzzy controller is nearly same as the proportional-derivative (PD) type controller. Figure 14 is indicative of the fuzzy rule table. The rule is included the rising correction of the angular speed response.

Design method of controller parameters by differential evolution
In this chapter, five parameters (S 1 , S 2 , S 3 , K pc and K ic ) of the proposed controller have to be designed. However, it is difficult to determine them by trial and error or some. Therefore, this chapter proposes the differential evolution (DE) to search the optimal controller parameters.
Here, DE is one of evolutionary optimized solution search methods. DE is the optimization method-based multi-point search method. In particular, basic GA expresses parameter by binary coding, whereas DE uses the parameters by real variable vector. The DE design is conducted by the initial population, the mutation, the crossover, and the selection. The design flow of DE is shown in Figure 15. In this chapter, DE/rand/1/bin design strategy is used for the determination of five controller parameters.
where D is the number of design parameter vectors, NP is the number of members in each population. Each parameter vector is represented by the parameter vector (target vector) x i,G , where G denotes one generation. The mutation vector v i,G is calculated by Eq. (10). From this equation, F indicates the step width (scaling factor) of DE design, and CR indicates of the crossover rate, where r 1 , r 2, and r 3 are different values. In Eq. (11), u j,G+1 is the vector of trial parameter, the rand is random value, and ST indicates the start point. The selection is utilized next algorithm, As previously described, the proposed method uses five control parameters (S 1 , S 2 , S 3 , K pc, and K ic ). The population size is 2000, the order of each vector is 20, and the coefficient of membership function F is 0.5. Moreover, the rate of crossover CR is 0.9. Then, the performance index function is shown in Eq. (13). Meanwhile, this chapter utilizes the inverse of y as a fitness function.

Verification results of computer simulation
Next, the simulation results of the proposed method are demonstrated by computer simulation. Table 3 shows the results of design parameter using the proposed method for two-mass model. Figure 16 is indicative of the transition of the maximum fitness function. In this simulation design, the step response and the disturbance response have been evaluated. Furthermore, the inertia ratio R is 1.07, and the stiffness of shaft K sn has been set to 18.5 Nm/rad in the simulation design. Figures 17 and 18 show the step responses that were obtained for the motor and load angular speeds, and armature current when using the proposed method. In this chapter, ω ref is 30 rad/s, the DC voltage input is 25 V, and the disturbance input T L is changed from 0 to 20% at t = 0.3 s. As shown by these figures, good waves are observed for the reference-following, vibration    suppression, and the disturbance performance. Figure 19 is indicative of the search process of the S 1 vector. Similarly, Figures 20-23 show the transition of the S 2 vector, S 3 vector, K pc vector and K ic vector, respectively. In particular, from Figure 23 and Table 3, K ic is 1.0 · 10 À6 of the design limitation value. Therefore, integral gain of the current PI controller can be omitted for this control object.

2-mass model
Next, the experimental results by using the proposed method are illustrated in this section. Figures 24 and 25 show the experimental results of two-mass model using the proposed method, where the condition (R = 1.07, K sn = 18.5 Nm/rad) is same as the above simulation results shown in Figures 17 and 18. From these figures, it is observed that the resonance vibrations between the motor and the load angular speed (ω M and ω L ) have been suppressed very well. Furthermore, after inputting disturbance, it can be seen that the angular speeds immediately have followed the reference speed ω ref without resonance vibrations. Hence, the validity of the control system, which consists of the proposed method, can be confirmed.

Effects of parameter variation
Next, it is described the effectiveness of robustness by the proposed design method. This section evaluates the robustness to variations in the ratio of inertia and the stiffness of the rigid shaft based on a nominal value. Figures 26 and 27 show the experimental results of the motor and load angular speeds obtained for the inertia ratio variation when using the same controller gains that were designed using the    proposed method, when R = [0.42, 2.65], where the disturbance torque input was skipped. From these figure, although it can be observed some overshoot and resonance vibration, the good results can be confirmed that were obtained for the design condition. Figure 28 shows the experimental results of the motor and load angular speeds obtained for the stiffness of shaft variation using the same controller gains, when K sn = 70.7. From this figure, it can be seen some resonance vibrations. However, the vibrations rapidly have been suppressed well.
Similarly, Figure 29 shows the experimental results when K sn = 3.1. As can be seen, the motor and load angular speeds oscillated and overshot. Therefore, if the stiffness of shaft of the experimental model is less than the design value, the settling time to suppress the resonance vibration becomes longer, although the proposed control system is not unstable. In addition, Figure 30 shows the experimental result when the control parameter redesigned with the stiffness of shaft K sn as the nominal value of experimental model. Good responses can be observed in this figure.
Furthermore, the proposed fuzzy control system is applied to a three-mass resonance model. Figure 31 shows the experimental results of the motor and load angular speeds when using the same controller gains designed for two-mass model (R = 1.07, K sn = 18.5 Nm/rad, where the nominal parameters of the three-mass experimental setup are J Mn = 2.774 · 10 À4 kgm 2 , J Ln = 2.940 · 10 À4 kgm 2 , K s1n = 18.5 Nm/rad, K s2n = 18.5 Nm/rad. From this figure, the effectiveness of the proposed method can be confirmed in a similar manner to the two-mass model case.

Conclusions
This chapter proposed the speed control system to suppress the resonance vibration of multiinertial model, especially two-mass system and three-mass system. The controller has been constructed with the digital fuzzy controller for speed control and the digital PI controller for current control. In the control system, only motor side state variables have been used for controlling the resonance system. Additionally, this chapter utilized the DE to determine these five controller parameters. Finally, the validity of the controller design, the robustness, and the control effectiveness of the proposed method has been verified using the simulations and the experiments by using the test experimental set up.