Simple Substrate Culture in Arid Lands

The limited water resources are the major factor that drew the attention towards the use of intensive agriculture in arid land. Protected cultivation was the first step, which started initially at late seventies and intensified at mid-eighties. Maximizing crop yield per square meter of soil as well as per cubic meter of water could be achieved using soilless culture systems [12]. The need for the use of soilless culture is becoming more important in arid lands than several years ago in order to increase the water use efficiency. In addition, continuous cultivation of crops resulted in poor soil fertility, which in turn has reduced the opportunities for natural soil fertility build up by microbes. This situation has led to poor yield and quality. In addition, conventional crop cultivation in soil (conventional open field agriculture) is difficult as it involves large space, large amounts of water and a huge number of labors [1].


Introduction
The limited water resources are the major factor that drew the attention towards the use of intensive agriculture in arid land. Protected cultivation was the first step, which started initially at late seventies and intensified at mid-eighties. Maximizing crop yield per square meter of soil as well as per cubic meter of water could be achieved using soilless culture systems [12]. The need for the use of soilless culture is becoming more important in arid lands than several years ago in order to increase the water use efficiency. In addition, continuous cultivation of crops resulted in poor soil fertility, which in turn has reduced the opportunities for natural soil fertility build up by microbes. This situation has led to poor yield and quality. In addition, conventional crop cultivation in soil (conventional open field agriculture) is difficult as it involves large space, large amounts of water and a huge number of labors [1].
Soilless agriculture means growing plants in the absence of land as the normal agricultural, where soil not used as a medium for agriculture but used as a support to the system. This technique can be an alternative to the conventional cultivation in the soil which has problems and difficult. In addition, soilless culture is possibly the most intensive method of crop production in today's agricultural industry in combination with greenhouses.
In protected cultivation, the high levels of crop and continuous cropping inevitably leads to problems of pests and diseases in the soil. The accumulation of these problems leads to a loss of yield and eventually of the crop. Cropping can only continue if some form of sterilization of the soil or rotation of crop can take place. Steam sterilization is not economically viable & not efficient, the use of methyl bromide banned in many European states, and it will band. For production to continue there is inevitably a move towards some form of soilless culture or soil replacement cultivation.
The use of soilless culture has substantially increased during the last decade as it contributes to the intensification of horticultural production and provides high crop yields even in areas with adverse growing conditions [12]. This chapter will discussed the importance of soilless culture of soilless culture in arid land, the constrain of using this type of cultivation, the type of soilless culture used in arid lands and the suitable types of substrate culture for arid lands.

Importance of soilless culture in arid land
Soilless culture technique provides a large numbers of advantages could be summarized as follows [9]: • Standardization of the culture, and of the root environment in particular.
• Excluding soil infection and hence the danger of disinfectant residues.
• Drastic reduction of energy input for the conditioning of the root environment.
• Crop production where the soil is unsuitable.
• Drastic reduction of the water consumption.
• Efficient use of nutrients.
• Better control of vegetative and generative plant development.
• Earlier and higher production.
• Rationalization of labor.
• More possibilities for culture mechanization and automatic control.

Why we have to move to this type of cultivation in arid lands
Most of the grower in the arid region now a day should move to the soilless culture for the following reasons:

Increase productivity
The matter of increased yields with the application of soilless culture should 'be examined carefully. It is true that precise control of nutrition to the plants grown in soilless cultures will result in higher yields and quality, but this does not necessarily mean that yields from the best cultures in soil are inferior. Nevertheless, it is difficult to believe that the fast increase in area in soilless culture in the Netherlands and other European countries would have occurred When using water cultures or aggregate cultures with inert substrates the level of nutrients, supplied to the new crops those chosen by the manager. This is not the case with soil cultures where in many cases excess nutrient levels in the soil from the previous crops produce salinity.
Another advantage of the soilless culture related to plant nutrition is the ability to control the pH and the E.C. of the nutrient solution according to the requirement of the crop and the environmental conditions. Similar control in soil cultures is very difficult and expensive [9].

Water economy and control
Water is the most important factor for crop production. Protected crops require large amounts of water due to exclusion of rainfall when crop production is required in hot, arid regions of the world; water is like to be a limiting factor not only of availability but also of quality and cost.
The advantage of soilless culture related to the ease of irrigation applies mainly to certain soilless systems, such as NFT and other true hydroponic systems (where the plants have their roots immersed into the nutrient solution) and to sub-irrigated substrate culture, and is not fully applicable to the rest of the soilless cultures using various inorganic or organic substrates. In fact, watering the later, the frequency and duration of irrigation is much more critical substrates with low water holding capacity, compared to soil.
With reference to water saving, certain soilless systems, for instance the closed or recirculated ones, undoubtedly economize water because drainage and evaporation from the surface eliminated by the design and operational scheme of the systems (NFT, "closed" systems, subirrigated soilless culture). In addition, with soilless culture, more accurate water supply control practiced.
Furthermore, water culture and sub-irrigated substrate systems save much labor in the time consuming task of checking and cleaning irrigation nozzles. On the contrary, crops grown on substrates and soil, require frequent examination of trippers as these can easily be blocked by calcium carbonate or other compounds especially with a "hard" water supply. The blockage problem can be eliminated either by acidification of nutrient solution or by pretreatment of irrigation water [9].

Reduction of labor requirement
Out of soil production exclude all cultural practices associated with the cultivation of the soil, sterilization of soil, weed control, etc. Labor requirement for soilless culture is not similar to all soilless systems. Therefore, the system itself, the degree of automation, the type of substrate, the number of crops raised on each substrate, etc. but in any case, generally speaking, there is a saving in labor impute when soilless culture employed [9].

Sterilization practices
The greenhouse soil must be free from any soil-borne pathogens before the establishment of any new crop. Sterilization is a difficult and costly operation, but necessary and of great importance. It is justified because the greenhouse business require high investment in structures, facilities, plant materials, running costs, etc. and the need to obtain maximum yields and returns, is obvious to have an economically viable operation. The most effective method of soil sterilization is by steaming, but the method is expensive due to the high cost of energy and labor, therefore its application eliminated. Chemical sterilization is less expensive but not without disadvantages, i.e. the use of formaldehyde had the problems of fumes which are highly phytotoxic and the most important chemical, methyl bromide, a very toxic material to handle, has the problem of chemical residues (bromide ions taken up by the crop) and environmenta1 pollution.
It is therefore, of great advantage the cultivation of crops outside of the soil as there is no need for sterilization when materials and substrates used only for one time, because spreading of diseases avoided. When "closed" soilless culture used depending on the system, the need for sterilization varies, i.e. to clean "true hydroponic" culture structures, following the removal of all debris, etc., a dilute rate of formaldehyde used, followed with clean water. In the NFT system, the film that forms the gullies can be replaced. When solid substrates are used, steam or chemical sterilization should be applied if the material is to be used again. In this case, the application of both is easier and economic but in any case, sterilization of soilless culture systems is easier than soil sterilization [9].

Control of root environment
Possibilities for more accurate control of root temperature, root oxygen supply are more easily to achieve in soilless cultivation [9].

Multiple crops per year
Due to the absence of the cultivation techniques, operations like soil cultivation, soil sterilization etc., the number of crops per year is increased, in a given production area, because the time interval between crops is nearly short [9].

Unsuitable soil
Soilless culture offers an ideal crop alternative to soil culture when there is no soil available at all, or there is no suitable soil for crop production, when soil salinity is higher or there are toxic substances into the soil and finally there is an accumulation of soil pathogens into the soil [9].

The constraint points for soilless culture in arid lands
• The high temperature most of the year.
• The availability of the soft water.
• The needed water for the cooling.
• The availability for the equipment in the country.
• The availability of the fertilizer for making the nutrient solution in the country.

Soilless culture system for producing vegetables in arid lands
Soilless culture divided into three major branches according the root growing media

Control of root environment
Possibilities for more accurate control of root temperature, root oxygen supply are more easily to achieve in soilless cultivation.

Multiple crops per year
Due to the absence of the cultivation techniques, operations like soil cultivation, soil sterilization etc., the number of crops per year is increased, in a given production area, because the time interval between crops is nearly short.

Unsuitable soil
Soilless culture offers an ideal crop alternative to soil culture when there is no soil available at all, or there is no suitable soil for crop production, when soil salinity is higher or there are toxic substances into the soil and finally there is an accumulation of soil pathogens into the soil.


The high temperature most of the year.  The availability of the soft water.  The needed water for the cooling.  The availability for the equipment in the country.  The availability of the fertilizer for making the nutrient solution in the country.

Soilless culture system for producing vegetables in arid lands
Soilless culture divided into three major branches according the root growing media

Hydroponics
Hydroponics is a technology for growing plants in nutrient solutions (water containing fertilizers). There are different types of hydroponics according the movement of the nutrient solution and the two main systems as follow:

Deep water culture
The plant roots grow in containers filled with water containing fertilizers (static water). In this system water mixed with nutrient solution and oxygen applied to the plants through nutrient solution using air pump or by mixing water with air. The plants are flouting on the nutrient solution using polystyrene sheet.

Hydroponics Aeroponics
Simple Substrate Culture in Arid Lands http://dx.doi.org/10.5772/59628 Hydroponics is a technology for growing plants in nutrient solutions (water containing fertilizers). There are different types of hydroponics according the movement of the nutrient solution and the two main systems as follow:

Deep water culture
The plant roots grow in containers filled with water containing fertilizers (static water). In this system water mixed with nutrient solution and oxygen applied to the plants through nutrient solution using air pump or by mixing water with air. The plants are flouting on the nutrient solution using polystyrene sheet.

Nutrient Film Technique (NFT)
In this system, the roots of the plants grow in a shallow film of water and nutrient solution inside cultivation channel or tube. The plants inserted in polyethylene (black on white) channel laid on a slope bed. The nutrient solution pumped into the channels in a thin film of nutrient solution and the excess nutrient solution collected and returned to the catchment tank.
Photo (1). Different systems of deep-water culture and nutrient film technique

Aeroponics
In this system, nutrient solution sprayed as a fine mist in sealed root chambers. The plants are grown in holes in panels of expanded polystyrene or other material. The plant roots suspended in midair beneath the panel and enclosed in a spraying box. The box sealed so that the roots are in darkness (to inhibit algal growth) and in saturation humidity. A misting system sprays the nutrient solution over the roots periodically. The system normally turned on for only a few seconds every 2-3 minutes. This is sufficient to keep roots moist and the nutrient solution aerated [1].

Aeroponics
In this system, nutrient solution sprayed as a fine mist in sealed root chambers. The plants are grown in holes in panels of expanded polystyrene or other material. The plant roots suspended in midair beneath the panel and enclosed in a spraying box. The box sealed so that the roots are in darkness (to inhibit algal growth) and in saturation humidity. A misting system sprays the nutrient solution over the roots periodically. The system normally turned on for only a few seconds every 2-3 minutes. This is sufficient to keep roots moist and the nutrient solution aerated.

Substrate culture
In this system, a solid medium provides support for the plants. As in liquid systems, the nutrient solution delivered directly to the plant roots. The substrate culture divided according to drainage procedure into two major systems according to drainage procedure ;km;,l ;l;l;

Open system
Closed system

Substrate culture
In this system, a solid medium provides support for the plants. As in liquid systems, the nutrient solution delivered directly to the plant roots. The substrate culture divided according to drainage procedure into two major systems according to drainage procedure

Open system
The open system is that when the nutrient solution applied to the system with the plants grow and then drained off as waste.
Because the leached or drained solution is not recirculated to the feeder tank, it does not require monitoring and adjustment. Once mixed, it is generally used until depleted. In addition, the quality of the irrigation water is less critical. A content of up to 500 ppm of extraneous salts is easily tolerated, and for some crops (tomatoes, for example) even higher salinities are permissible, although not desirable. It is advisable to monitor the growing medium, particularly if the irrigation water is relatively saline or if the operation is located in a warm, high sunlight region. To avoid salt accumulation in the medium, enough irrigation water is used to allow a small amount of drainage or "leaching" from the bags. This drainage should be collected and tested periodically for total dissolved salts [1].

Closed system
Closed system works in the same way as open system with on important difference that nutrient solution which run-off after each application is collected and recirculated to be used in successive irrigation times.
Closed systems are economical in the use of nutrients, but require frequent monitoring and adjustments of the nutrient solution. Measuring (EC) is a convenient check of total salt concentration, but provides no data on the concentration of major elements, and it is virtually unaffected by the amounts of trace elements present. Periodic chemical analyses are required, usually every two or three weeks for major elements and every four to six weeks for trace elements.
Small farmers commonly practice this regime: Begin with a new solution; at the end of a week add one-half of the original formula to the solution. At the end of the second week, dump the remaining mixture from the tanks or sumps and start all over again [1].

Substrate culture
In this system, a solid medium provides support for the plants. As in liquid systems, the nutrient solution delivered directly to the plant roots. The substrate culture divided according to drainage procedure into two major systems according to drainage procedure ;km;,l ;l;l;

Open system
Closed system Some individual materials (substrates) can provide all four functions, but not at the required level of each. For example, sand provides excellent support and gas exchange but has insufficient water-and nutrient supplying capacity [9].

Characteristics of appropriate substrates
• Capacity to hold water The capacity to hold and drain surplus water depends on the texture of the medium, the size and form of its granules and the permeability. The smaller granules have more surfaces, are close to each other, and therefore, can hold more water. Also the uneven form of granules has a surface area more than granules of even or round form thus the first has higher capacity to hold water.
Consequently, the size of granules should be appropriate so that it can hold proper quantity of water suitable to the crop to be grown [1].
• The substrate should have good aeration and good drainage capacity The substrate should have a good drainage capacity for draining surplus water and therefore, ensures good aeration around roots. Therefore, we should avoid substrate/medium with fine granules which impedes the movement of oxygen through such granules, reducing the overall aeration condition in the growing environment and leads to asphyxiation of plant roots [1].
• The substrate should be free from harmful or poisonous materials The substrate should be free from any material, which may cause harm to plant roots or affect plant growth such as sand and small stones of lime origin (contain calcium carbonate). This should be avoided as it can increase the nutrient solution pH to more than 7. This increase leads to sedimentation of iron and phosphorus causing a symptom of deficiency although they exist in the solution.
• The substrate should be supportive to plants growing in it The substrate should be acting to fix the plants properly. This depends on the texture of the substrate, which should be medium-heavy to fix plant roots [1].

• To be free from diseases incitements
The substrate should be free from different pests and insects so that it would not form a source of infecting plants by different diseases [1].
• To be free from salinity The substrate should be free from salinity to avoid affecting the growing plants. For instance, the medium made of wood dust usually contains high concentration of sodium chloride due to soaking the wood in salt solution for long periods [1].
• The substrate should be free from weed seeds This is to avoid being a source of weeds, which will grow and compete with the main crop for nutrition and water. In many cases, weeds would also be a host for some diseases, which would infect and damage the growing plants [1].
• To be slow in the decomposition process In case of using organic medium, it would preferably be of slow deteriorating nature so that it continues to be in the best condition for the longest period possible. This will reduce the cost of changing the substrate annually [1].
• To be easily transported, handled, and less expensive There are many kinds of substrates but it is important that the selected one be available in several locations to facilitate its handling and transportation. This would result in reducing the cost of transportation and hence, the preliminary cost of establishing the roof garden. The price of the substrates should be appropriate and acceptable so that the system adopted by all categories of the society [1].

Types of growing media
Growing media "substrates" can classified as follows: Inert media: A solid inert material for supporting the plant and provides air and water availability conditions to the roots such as perlite, sand, Rockwool, volcanic gravel, pumice...etc.
Organic media: A natural organic material for supporting the plant such as peat moss, coconut fibers, coco peat, rice hush, wood bark...etc.
There are several raw materials, which used as substrates for roof farming. Such materials differ from one another about its physical characteristics. Due to variations and multiplicity in the forms and types of materials available in the surrounding environment, there is a need for particular criteria, which enables us to select the appropriate material for an agricultural medium (substrate) [9].

Peat moss
The Peat moss considered the most common substrate and widely used at global level. It is a decomposed organic material available in humid locations of the globe called Peat moss mines. This material used separately or mixed with other substrates such as vermiculite or sand.
The peat moss characterized by the following: • Large capacity to absorb water about 8 folds of its weight at saturation level and drains surplus water.
Soilless Culture -Use of Substrates for the Production of Quality Horticultural Crops • High percentage of organic matter (94-99%).

Rice husk
The characteristics of rice husk presented below: • Very light weight.
• Provides necessary aeration for roots of different plants. If mixed with a substrate of bad aeration, it can improve airing and drainage capacity.
• Has a medium capacity to hold water.
dled, and less expensive strates but it is important that the selected one be available in several nd transportation. This would result in reducing the cost of transportation f establishing the roof garden. The price of the substrates should be he system adopted by all categories of the society.

.3. Coconut fibers
The coconut peat and fibers have recently used as substrate for soil-less agriculture. It obtained from the coconut fruits.

Characteristics of coconut fibers:
• Possibility of use for more than one year without any change in its physical characteristics.
• Its decomposition slow therefore, it would not deteriorate quickly.
• Has capacity to hold water.
• Can provide enough airing to the substrate. est materials used as a solid substrate for sands containing lime due to the high rate welding material for sand granules and and. It is also advisable not to use coast t is preferable to use sands of granite or . The diameter of sand granules is an on of agriculture substrate with sand. The y of moisture and very fine sand does not haracterized by good drainage capacity but re, it is preferable to mix it with peat moss nesium silicate, which obtained from metallic chips from Mica mines in terial to use as a substrate obtained by ature of 1000 centigrade. Therefore, the reates an increasing pressure inside its all light pieces of good porosity and iculture.
: assium in an absorbable form for the at vermiculite is a good water absorption es to be wet most of time; hence, it is materials to reduce such permanent wet condition so that it would be th.
olcanic lava of color graded from grey to white and consist of Aluminum is grinded and heated to high temperature from 900-1000C. This results ng air gaps, which cause large expansion, and swelling of granules.
consistence with no capacity of cationic Sand considered one of the best and oldest materials used as a solid substrate for growing plants. It is preferable not to use sands containing lime due to the high rate of calcium carbonate, which acts as a welding material for sand granules and changes the physical characteristics of sand. It is also advisable not to use coast sands due to its high content of salt. It is preferable to use sands of granite or silicone origin as agriculture substrate. The diameter of sand granules is an important factor for successful preparation of agriculture substrate with sand. The course sand cannot hold enough quantity of moisture and very fine sand does not allow a sufficient rate of aeration. Sand characterized by good drainage capacity but its ability to hold water is weak. Therefore, it is preferable to mix it with peat moss or compost.
an one year without any change in its ore, it would not deteriorate quickly. the substrate.
ldest materials used as a solid substrate for se sands containing lime due to the high rate a welding material for sand granules and sand. It is also advisable not to use coast It is preferable to use sands of granite or te. The diameter of sand granules is an tion of agriculture substrate with sand. The ity of moisture and very fine sand does not characterized by good drainage capacity but fore, it is preferable to mix it with peat moss agnesium silicate, which obtained from metallic chips from Mica mines in aterial to use as a substrate obtained by erature of 1000 centigrade. Therefore, the creates an increasing pressure inside its small light pieces of good porosity and griculture.

re:
otassium in an absorbable form for the that vermiculite is a good water absorption nues to be wet most of time; hence, it is

Vermiculite
It is dehydrated iron, aluminum and magnesium silicate, which obtained from metallic chips from Mica mines in Africa, Australia, and America. The material to use as a substrate obtained by treating the raw element with a temperature of 1000 centigrade. Therefore, the humidity transforms to vapor which creates an increasing pressure inside its layers, which in turn fragmented to small light pieces of good porosity and characteristics appropriate to soil-less agriculture.
it is preferable to mix it with peat moss sium silicate, which obtained from metallic chips from Mica mines in rial to use as a substrate obtained by re of 1000 centigrade. Therefore, the tes an increasing pressure inside its ll light pieces of good porosity and lture.
sium in an absorbable form for the vermiculite is a good water absorption to be wet most of time; hence, it is aterials to reduce such permanent wet condition so that it would be .
canic lava of color graded from grey to white and consist of Aluminum grinded and heated to high temperature from 900-1000C. This results air gaps, which cause large expansion, and swelling of granules.
nsistence with no capacity of cationic lding enough water. However, irrigation y to guarantee the water and nutritional ons. rosity which facilitates its irrigation by rately with good results or in a mix with grow several vegetable crops, seeds, flowers, and indoor ornamental Some characteristics of Vermiculite are: • High capacity to hold water.
• Contains magnesium and potassium in an absorbable form for the benefit of plants. It has noted that vermiculite is a good water absorption material and therefore, continues to be wet most of time; hence, it is preferable to mix it with other materials to reduce such permanent wet condition so that it would be more appropriate for plant growth.

Perlite
This is a volcanic stone originated from volcanic lava of color graded from grey to white and consist of Aluminum Silicate + Sodium and Potassium, which is grinded and heated to high temperature from 900-1000°C. This results to swelling due to exodus of hot air forming air gaps, which cause large expansion, and swelling of granules.
st materials used as a solid substrate for ands containing lime due to the high rate elding material for sand granules and d. It is also advisable not to use coast is preferable to use sands of granite or The diameter of sand granules is an of agriculture substrate with sand. The of moisture and very fine sand does not racterized by good drainage capacity but , it is preferable to mix it with peat moss esium silicate, which obtained from metallic chips from Mica mines in rial to use as a substrate obtained by ure of 1000 centigrade. Therefore, the ates an increasing pressure inside its all light pieces of good porosity and ulture.
sium in an absorbable form for the t vermiculite is a good water absorption s to be wet most of time; hence, it is aterials to reduce such permanent wet condition so that it would be h.
lcanic lava of color graded from grey to white and consist of Aluminum grinded and heated to high temperature from 900-1000C. This results g air gaps, which cause large expansion, and swelling of granules.
onsistence with no capacity of cationic lding enough water. However, irrigation y to guarantee the water and nutritional ions. rosity which facilitates its irrigation by rately with good results or in a mix with o grow several vegetable crops, seeds, flowers, and indoor ornamental Some characteristics of Perlite are: • A material of stable physical consistence with no capacity of cationic alternation.
• A light weight material. • Good drainage capacity while holding enough water. However, irrigation is preferred several times per day to guarantee the water and nutritional elements needed by the plants.
• A substrate of good airing conditions.
• A material of good capillary porosity which facilitates its irrigation by sub-surface method.
• Perlite is widely used either separately with good results or in a mix with other substrates like peat moss to grow several vegetable crops, seeds, flowers, and indoor ornamental plants.

Calcined or Expanded clays
Heating montmorrillonitic clay minerals to approximately 690ºC forms calcined clays.
The pottery-like particles formed are six times as heavy as perlite.
Calcined clays have a relatively high cation exchange as well as water holding capacity.
This material is a very durable and useful amendment [11].
pproximately 690ºC forms calcined clays. es as heavy as perlite. exchange as well as water holding capacity. endment.
. in composition and fragmented material. hich give pumice a low , the commercial term for fine-grained in diameter, may be deposited some from silicic lavas rich in dissolved on, sudden release of pressure leads rates a frothy mass of expelled lava. tmosphere as a vent filling or flow, umice has many advantages such nd high surface area, which result rom the chemical point except that it contain calcium carbonate ith acid leading to a reduction in the size of the particle. This ger time, the substrate can be compacted. teristics, where this material is heavier. not hold it for a long period.
Expanded Clay Pumice

Pumice
Pumice is direct product of acidic volcanism. It is a highly vesicular volcanic glass, silicic in composition and occurs as massive blocks or unconsolidated, fragmented material. The vesicles are glass-walled bubble casts, which give pumice a low density compared to natural glass. Pumicite, the commercial term for fine-grained, fragmented pumice with shards under 2mm in diameter, may be deposited some distance from the source. Pumice is formed from silicic lavas rich in dissolved volatiles, particularly water vapor. On eruption, sudden release of pressure leads to expansion of volatile which, in turn, generates a frothy mass of expelled lava. This mass may solidify on contact with the atmosphere as a vent filling or flow, or may be shattered by a violent eruption. Pumice has many advantages such as high strength-toweight ratio, insulation and high surface area, which result from the vesicular nature of this rock [11]. amendment.
ism. ic in composition and d, fragmented material. s, which give pumice a low ite, the commercial term for fine-grained m in diameter, may be deposited some ed from silicic lavas rich in dissolved ption, sudden release of pressure leads nerates a frothy mass of expelled lava. e atmosphere as a vent filling or flow, . Pumice has many advantages such n and high surface area, which result from the chemical point except that it contain calcium carbonate t with acid leading to a reduction in the size of the particle. This onger time, the substrate can be compacted. racteristics, where this material is heavier. es not hold it for a long period. . , contains Aluminum, Potassium, Sodium, traces of Iron, Calcium, ps, which formed because of hot vapor exodus before the volcanic n its natural form and does not need ppropriate size of granules.
o Perlite from the chemical point of ristics, as the first material is heavier. esn't hold it for a long period. . in agriculture particularly in Europe where it used to produce many contains Diabase (60%), Lime stone (20%) and Coal (20%). melting together. The melted material is transformed to fine threads t centrifugal machine and cooling. The threads are then compressed

Expanded Clay
Pumice Some characteristics of pumice • Pumice a material similar to Perlite from the chemical point except that it contain calcium carbonate which make a problem which react with acid leading to a reduction in the size of the particle. This reduction of particle after using for longer time, the substrate can be compacted.
• It differ than perlite in physical characteristics, where this material is heavier.
• Does not absorb water easily and does not hold it for a long period.
• A substrate of good airing condition.

Foamy rock
This is a silicon rock of volcanic origin, contains Aluminum, Potassium, Sodium, traces of Iron, Calcium, and Magnesium. The material has several gaps, which formed because of hot vapor exodus before the volcanic lava cools down. This material is available in its natural form and does not need heating but only breaking and grinding to the appropriate size of granules.
Some characteristics of Foamy rock are: • Foamy rock is a material similar to Perlite from the chemical point of view but differs in physical characteristics, as the first material is heavier.
• Does not absorb water easily and doesn't hold it for a long period.
• A substrate of good airing condition.
• Easy to clean and purify.

Rockwool
The use of rockwool has quickly spread in agriculture particularly in Europe where it used to produce many vegetable and ornamental crops.
This mix heated to very high temperature for melting together. The melted material is transformed to fine threads of 5-micron diameter after treatment with fast centrifugal machine and cooling. The threads are then compressed and divided into the required sizes. During the cooling process, the phenol material added to help sticking the rocky wool into a substrate of good porosity.

Important forms and uses of rockwool
• Germination cubes: This could be in a single or aggregated form.

• Seedlings blocks:
To accommodate the small germination cubic's with its contents of plants or the young seedlings directly.
• Agricultural slices: To which seeds of proper size transferred, where plant completes its life cycle.
• Loose (unpacked) rock wool: This used as substrates for cultivation in pots or mixed with other substrates to improve the characteristics of airing and water holding.

Some characteristics of rockwool are:
• Dry material does not contain any nutritional or non-nutritional solution.
• Sterilized material free of pests, insects, and disease.
• Very light but solid material. This facilitates its preparation and processing.
• A material of high porosity (97% of the total size) which facilitates drainage.
• Facilitates disposal of salt sediments through adding water only in the open system for leaching.
d does not hold it for a long period. ition.
rigin, contains Aluminum, Potassium, Sodium, traces of Iron, Calcium, l gaps, which formed because of hot vapor exodus before the volcanic ble in its natural form and does not need the appropriate size of granules.
: ilar to Perlite from the chemical point of racteristics, as the first material is heavier. d doesn't hold it for a long period. ition.
read in agriculture particularly in Europe where it used to produce many and contains Diabase (60%), Lime stone (20%) and Coal (20%).
for melting together. The melted material is transformed to fine threads fast centrifugal machine and cooling. The threads are then compressed • Easy to sterilize and could be used for more than a year.
ded into the required sizes. During the cooling process, the phenol material added to help sticking the ool into a substrate of good porosity. Easy to sterilize and could be used for more than a year. ve substrates used separately or in the form of mixture of more than one substrate.

nt forms and uses of rockwool
trates Mixtures ve-mentioned substrates could be used in a separate form as agricultural substrate or may be mixed to attain the best characteristic for the plants to be grown. strate characteristic has a strong impact on success of agricultural operation because it determines the between water needed for plant growth and the air necessary for root's breathing. It is therefore, necessary small gaps to help holding of water needed for plant life and large gaps required to ensure air necessary owth. Some of the most important characteristics, which assessed, are: Substrate The above substrates used separately or in the form of mixture of more than one substrate.

Substrates mixtures
The above-mentioned substrates could be used in a separate form as agricultural substrate or may be mixed together to attain the best characteristic for the plants to be grown.
The substrate characteristic has a strong impact on success of agricultural operation because it determines the balance between water needed for plant growth and the air necessary for root's breathing. It is therefore, necessary to have small gaps to help holding of water needed for plant life and large gaps required to ensure air necessary for its growth. Some of the most important characteristics, which assessed, are: • Substrate's weight The design was as follow: Five 0.8 * 38rn trenches for each tunnel were excavated to a depth of 20 or 40 cm. The bottom of each trench was first leveled and graded to a slope of 12 cm per 40m [5]. The profile of the trench was adjusted to 1 (V) shape. The trench was lined with a water proof polyethylene sheet (200 p) to prevent plants from rooting into the original soil [6]. The surface of the bed was sloped to be parallel to the bottom of the trench. There inches corrugated perforated plastic pipe placed along the bottom of each trench. The drains were connected at the lower end to a main drain that sink into a 9 m3 nutrient tank.
Once the drain pipes are in place, washed coarse sand obtained from Cairo -Alex. Desert road (km 40) filled to a depth of either 20 or 40 cm.
The nutrient tank was 2.0 m length X 1.5 m width X 3.0 m height with 30 cm thick concrete construction, coated with bituminous paint. This tank divided into two equal parts each designed to hold a volume of 30 to 40 % greater than maximum volume required for daily irrigation of each tunnel [10]. A float valve attached to a water refilling line in order to maintain the water level in the tank. The system is designed to recirculate the nutrient solution frequently from the nutrient tank by means of a submersible pump (1 Hp, 220V, and 2 inch in diameter outlet pipe) that was operated by a time clock, one or two times daily.
Some solid particles could be released into the recirculating solution, therefore filtration would be necessary. In fact, the tank acts as a sedimentation tank for the solid particles, which released from the main underground water supply or from recirculated nutrient solution. In addition, two filtration systems were used:

1.
A coarse filter "Nylon stocking" was fitted on the outlet of the main drain pipe before the nutrient tank.
2. 150 mesh screen filter were fitted between the circulation pump and the inlet pipe to the main irrigation pipe, in such a way that it is easily removed for cleaning.
The filtration units particularly the screen filter have to be cleaned and replaced fairly frequently because solid particles retained on the screen will progressively reduce the flow rate through the screen. A drip irrigation system was used with this sand culture [7] with excess nutrient solution (over 50 % of the total applied) to maintain recycling. Such system is termed as a closed system. The drip irrigation system feeds each plant individually by the use of two-liter emitter.
Drip irrigation system of each plastic tunnel contains 50 mm in diameter polyethylene header line. From this header line, 18 mm polyethylene pipe run along each plant row. The emitters were placed in these lateral lies at the base of each plant (50 cm distance between successive plants).
It is worthily to mention that, emitters, pipes fittings of drip irrigation system used for both soil or sand culture and the cover of nutrient tank should be black to prevent algae growth inside the piping system or the nutrient tank.
It is essential that materials used to construct the closed sand culture should not be phytotoxic.
In other words, they should not have any harmful effect on the plants. No phytotoxicity has been reported from the use of concrete, bituminous pipes or sheets [5].

Polystyrene pot system
There are two main systems for the polystyrene pot system:

Vertical pot system (Condensing system):
Different production systems for different crops introduced to small growers in the APRP region by ICARDA-APRP. For production of cash crops such as strawberries and beans, the vertical soilless production system was adapted to maximize growing space by growing the crops vertically. Such technique for strawberry has been investigated for last four years in Bahrain, Kuwait, Oman and Saudi Arabia and currently in Egypt has proved promising from the view point of productivity, cost and water saving. The fundamental structure of the system is the columns, which consist of 8-12 growing containers made from polystyrene on top of each other as seen in the photo. These column of polystyrene pots installed in sloped channel lined by polyethylene sheets to collect the excess of nutrient solution. At the end of the channels there is a PVC tube to collect the return nutrient solution delivering them to filter then to the nutrient solution tank. The column supported by one inch PVC tube from inside the pots. The pots filled substrate (peat moss: perlite 1:4 v/v). The crops are planted in the 4 corners of these containers. The irrigation water and nutrition solution applied to the plants using the drip irrigation and the excess of irrigation recirculated in closed system. The growing containers made locally and the system could be installed in any greenhouse or even in the open field.
Main advantages of the system The production of strawberries in the vertical hydroponics system was quite successful. The hydroponics system showed followings advantage over the traditional soil-bed production system: 1. 30-50% savings in the cost of the production materials; 4. Longer production season;

5.
Increased income due to early season production when prices are high; and 6. Far less incidence of pests and deceases. As a result, lesser chemicals used and higher quality produces obtained.

Simple pot system
For production of cash crops such as tomato, pepper, cantaloupe...etc, the recirculation pot system adapted to maximize growing space by growing the crops in polystyrene pots. Such technique for the cash crops has been investigated for last four years in Bahrain, Kuwait, Oman and Saudi Arabia and currently in Egypt has proved promising from the view point of productivity, cost and water saving. The fundamental structure of the system is simple containers made from polystyrene inserted in a sloped channel lined by polyethylene as seen in the photo. The crops are planted in these containers in substrate consists of perlite: peat moss (4:1 v/v). The irrigation water and nutrition solution applied to the plants using the drip irrigation and the excess of irrigation recirculated in closed system.

Polyethylene containers
There are different types of containers is suitable to substrate culture in arid lands. Also, the different containers shapes create different substrate systems as follow:

Open toped container (Vertical containers)
This type of containers suitable for substrate can hold the water because it can allow a longer column of substrate for the big plants and allowed the water to be drained by gravity.
The idea for these containers to have a holes at the lowermost of the container (5 cm from the bottom) to allow the water to drain. The container filled with small gravel in these 5 cm and then by the chosen substrate. If the open system is used, the containers installed on a bed covered by polyethylene sheets and the drain water is collected and used in another use. If the closed system is used, there a gutter is installed and the containers are installed inside these gutter. The drain water collected and delivered to the nutrient solution after filtering to the nutrient solution tank.

Horizontal bags
The idea of these bags is use for the substrate cannot hold the water like perlite. These bags have a short side and there are holes at the lowermost to drain the excess water. When these bags filled with water, part of these holes will be blocked and keep some water at the bottom of the bags to be a pool can supply the roots with water and nutrient.
This type of containers suitable for substrate can hold the water because it can allow a longer col substrate for the big plants and allowed the water to be drained by gravity.
The idea for these containers to have a holes at the lowermost of the container (5 cm from the bot allow the water to drain. The container filled with small gravel in these 5 cm and then by the chosen subs the open system is used, the containers installed on a bed covered by polyethylene sheets and the drain w collected and used in another use. If the closed system is used, there a gutter is installed and the contain installed inside these gutter. The drain water collected and delivered to the nutrient solution after filtering nutrient solution tank. Photo (8) container system using polyethylene bags Photo (9) container system using polyethylene Photo (10) container system using polyethylene containers There are different types of containers is suitable to substrate culture in arid lands. Also, the different rs shapes create different substrate systems as follow:

pen toped container (Vertical containers)
This type of containers suitable for substrate can hold the water because it can allow a longer column of e for the big plants and allowed the water to be drained by gravity.
The idea for these containers to have a holes at the lowermost of the container (5 cm from the bottom) to e water to drain. The container filled with small gravel in these 5 cm and then by the chosen substrate. If n system is used, the containers installed on a bed covered by polyethylene sheets and the drain water is d and used in another use. If the closed system is used, there a gutter is installed and the containers are inside these gutter. The drain water collected and delivered to the nutrient solution after filtering to the solution tank.
(8) container system using polyethylene bags Photo (9) container system using polyethylene pots (10) container system using polyethylene containers Figure 9. Container system using polyethylene pots

Polyethylene containers
There are different types of containers is suitable to substrate culture in arid lands. Also, the different containers shapes create different substrate systems as follow:

Open toped container (Vertical containers)
This type of containers suitable for substrate can hold the water because it can allow a longer column of substrate for the big plants and allowed the water to be drained by gravity.
The idea for these containers to have a holes at the lowermost of the container (5 cm from the bottom) to allow the water to drain. The container filled with small gravel in these 5 cm and then by the chosen substrate. If the open system is used, the containers installed on a bed covered by polyethylene sheets and the drain water is collected and used in another use. If the closed system is used, there a gutter is installed and the containers are installed inside these gutter. The drain water collected and delivered to the nutrient solution after filtering to the nutrient solution tank.
Photo (8) container system using polyethylene bags Photo (9) container system using polyethylene pots Photo (10) container system using polyethylene containers

Water quality control in the arid lands
The limited water resources and rapid increase in population were the major factors that drew the attention towards the use of substrate in the arid lands.
The best water for substrate cropping is rainwater or water condensed from moisture -laden air. Water from these two sources has virtually no dissolved substances in it. Consequently, there is no build -up of excess ions coming into the substrate installation with the make -up water. An economy in the arid lands, the use of this scarce water can be obtained, if it is mixed with less pure water to provide a blended water in which the concentration of dissolved substances is still acceptable. If the water, that is being used has dissolved in it a substance that is being supplied by the make -up water at a faster than the crop is removing it, then an excess will accumulate in the recirculating solution. If the build -up of the excess is not too rapid, then it is quite realistic to pump out the nutrient solution from the installation after a period of time that was not sufficient duration for an adverse concentration to build up. [2] suggested to obtain an analysis of the water supply in ppm for the following ions : nitrogen phosphorus,potassium calcium magnesium iron manganese boron, copper, molybdenum, zinc, sodium, chlorides and sulphate. From an inspection of the analytical data it should be possible to decide which ion, or ions, may build up to adversely high concentrations.
Arrangements should then be made for weekly analyses to enable the concentration of the suspect ion (or ions) to be plotted on a graph as the concentration build up. Close observation of the crop will indicate when appearance of the plants begins to be not quite right. However, this method is very -expensive.
On the other hand, [8] suggested a method for deciding when the nutrient solution can be discharging when the hard water was used. This method used successfully in Egypt when the ground water used in the substrate system.
The author suggested that the two most common salts dissolved in the hard water are calcium and magnesium. Electrical conductivity, monitored as EC increases as nutrient salts dissolved in the solution. It follows then that natural salts dissolved in water added to the EC. The EC of the water before nutrients added is known as the base EC. Use the conductivity meter to measure base EC taking care to use a representative sample, i.e., from a pond or other open water source. Collect from "open" water not from puddle edges, from the tap; run the tap for a minute before collecting the sample. If your CF meter is not 'temperature compensated adjust the sample temperature to around 20 "C before taking a reading. The author divided the water to: The sum of the effects of using hard water make -up supplies is that, after nutrients additions to a pre-determined level, desired EC subsequent changes in solution EC don't solely reflect the removal of nutrient from the solution by the plants. This situation manifests itself as stable solution EC when make -up water EC additions more or less equate with nutrient losses, or as rising solution EC when make -up water EC additions are greater than nutrient losses. Sometimes, the solution EC may fall if marginally hard water is used. Irrespective of the manifestation, the effect is a gradual decline of the nutrient status of the solution. This decline must be arrested and the following procedure demonstrates how this is done

At system start -up
Fill the nutrient solution tank with clean water, begin circulation and bring the system to operating capacity. Check, and note, the base CF of the water in the nutrient solution tank. Add the acid to reduce water pH close to desired pH "between 6 -6.5". The amount of acid used will depend on the hardness of the water. It is useful to keep a record of the amount of acid required so that future treatment of the same volume, after solution discharges, will be rapidly accomplished. Do not overdose; avoid lowering the pH much below 6.0.
Determine desired EC depending on the crop and use the following equation: Add nutrient A first and allow this to disperse a little before adding B. Allow time between nutrient additions and monitoring EC for the nutrients to disperse throughout the system. This process may be encouraged by stirring the solution in the circulation tank. When target EC achieved check solution pH and adjust if necessary.
The following examples illustrate this procedure : • Base EC of make -up water 6 • Solution volume in the nutrient solution tank 210 liters

Discharging the solution
Eventually the target EC will be raised to an unacceptably high value. Generally, this occurrence dictates the time the solution should discharged. The frequency of discharging will regulated by the rate of water removal by the plants of course, but also and particularly by the hardness, manifested as base EC of the make -up water.
The general advice, found to have great practical utility, is to allow the rise in EC to continue until it passes a value 50 % greater than the original EC. When it reaches this value you have to discharge the nutrient solution.
Some mono crop growers a dot the procedure of discharging the solution when the target EC reaches twice the desired EC.
10. The special program for using very hard water (0.9 or above) The principal problems with very hard water supplies, base EC 0. 9 m.mhos or above, are these: First, because of the very high level of natural salts present, there is a large oversupply of those which are also nutrient salts, so that a smaller proportion are removed from the system due to take up by the plants.
Second, large amounts of acid are required to neutralize the salts. The result is that' start -up solution EC, already high due to high base EC, is quickly increased by make -up water and acid additions, and there is reduced scope to assign these EC increases to useful nutrients. The practical significance is that the full base EC must be allowed at system start -up when calculating a target EC and when maintaining nutrient levels in the solution by setting a new target EC. Accordingly, when using very hard water supplies, calculation of target EC uses the following equation: Target EC = Desired EC + Base EC Then it follow the same procedure as described in the hard water (EC 0.4 -0.8 m.mhos)

Nutrient solution composition
Plants require 16 essential elements for their growth and development. Without these nutrients, plants cannot complete their life cycles and their roles in plant growth cannot replaced by any other elements. These 16 elements divided into micro and macro element categories as sketched bellow.

Discharging the solution:
Eventually the target EC will be raised to an unacceptably high value. Generally, this occurrence dictates the time the solution should discharged. The frequency of discharging will regulated by the rate of water removal by the plants of course, but also and particularly by the hardness, manifested as base EC of the make -up water. The general advice, found to have great practical utility, is to allow the rise in EC to continue until it passes a value 50 % greater than the original EC. When it reaches this value you have to discharge the nutrient solution. Some mono crop growers a dot the procedure of discharging the solution when the target EC reaches twice the desired EC.
10. The special program for using very hard water (0.9 or above) The principal problems with very hard water supplies, base EC 0. 9 m.mhos or above, are these: -First, because of the very high level of natural salts present, there is a large oversupply of those which are also nutrient salts, so that a smaller proportion are removed from the system due to take up by the plants. Second, large amounts of acid are required to neutralize the salts. The result is that' start -up solution EC, already high due to high base EC, is quickly increased by make -up water and acid additions, and there is reduced scope to assign these EC increases to useful nutrients. The practical significance is that the full base EC must be allowed at system start -up when calculating a target EC and when maintaining nutrient levels in the solution by setting a new target EC. Accordingly, when using very hard water supplies, calculation of target EC uses the following equation: Target EC = Desired EC + Base EC Then it follow the same procedure as described in the hard water (EC 0.4 -0.8 m.mhos)

Nutrient solution composition
Plants require 16 essential elements for their growth and development. Without these nutrients, plants cannot complete their life cycles and their roles in plant growth cannot replaced by any other elements. These 16 elements divided into micro and macro element categories as sketched bellow.
All the nutrient elements required for plant growth have to be present in the nutrient solution for soilless culture systems. Some of the elements may be present in adequate quantities as in the water supply. Other elements will have to be added to the water. These usually are: N -P -K -Ca -Mg -Fe-Mn -B -Cu -Zn -Mo.

Conclusion
It is clear to solve the problems in the arid lands as shortage of water and lack of technology and the limited income of the grower that using simple but the high technology substrate culture can be a substitute of the soil cultivation. This is because that most of the equipment produced locally, the prices of this equipment's is reasonable and can afforded by the medium class grower special the grower is producing for export. This technique is saving water, there is no need of soil sterilization, there is no for land reclamation.
The most system of the simple substrate system is the column polystyrene pot system for the small plants and the single polystyrene system for the big plants, which can isolate the plants from the high temperature.

Author details
Usama Ahmed Aly El-Behairy