Bioremediation of Crude Oil Contaminated Soil by Petroleum-Degrading Active Bacteria

Approximatelly 0.6 million tons of petroleum is poured into soil, groundwater, rivers and oceans every year in China. A large amount of the oil contaminated soil has not been remediated. The contaminated soil poses a severe threat to the environment and must be taken care of. Bioremediation has become one of the most popular and promising technologies with growing demand for the remediation of petroleum contaminated soils because pollutants can be completely removed at low cost.


Introduction
Areas of contaminated soil have increased rapidly in recent years due to the continuous growth and development of the oil industry.Meanwhile, the level of contamination becomes severe as time elapses.
Contaminated soils include many complex compounds such as alkanes, benzene, methylbenzene, and benzene, among others.These contaminants are toxic and usually categorized as carcinogenic substances.They can not be easily eliminated and eventually these contaminants will leach into the groundwater systems [1,2] .Consequently, oil contamination is a serious environmental problem to our living ecosystem.
Bioremediation of oil contaminated soil requires low cost and does not lead to secondary pollution.In the last decades, relevant bioremediation techniques have been wildly studied.Most of these studies focused on enhancing bioremediation efficiency by increasing the activities of the native microorganisms by adding nutrients such as nitrogen (N) and phosphorous (P) [3] .These studies have shown that native microbes need a long time to domesticate due to slow growth rates.In addition, the low metabolic activities of these native microbes make a rapid decontamination difficult.Therefore, the application of bioremediation using indigenous microbes is restricted.Fortunately, petroleum-degrading active bacteria could be the solution to this problem.For instance, the Baltic General Investment (BGI) Corporation in America uses mixed microbes to improve bioremediation [4] .The research of Wilson (1993) presents bacteria strains which have shown high degradation rates of polycyclic aromatic hydrocarbons (PAHs) [5] .Bioremediation of petroleum contaminated soil is a complicated process, in which the pollutants characteristics, the ecological structure of microbes, and the environmental conditions must be considered.The adaptation characteristics of petroleum-degrading active bacteria can influence bioremediation.In this research, several strains were isolated from oil contaminated soils from the northern region of the Shaanxi province.The objectives of this work were to establish the characteristics of the strains and the kinetics of the bioremediation process.

Crude oil and petroleum contaminated soil samples
Samples of the crude oil and the petroleum polluted soil used in this study were collected from oil wells located in the northern region of the Shaanxi province.The characteristics of the polluted soil samples are shown in Table 1

Methodology
The procedure for bacteria gathering, separation, and purification was as follows.Ten grams (10 g) of crude oil contaminated soil were quantitatively placed into a 100 mL of culture medium (250 mL flask).This mixture was shaken using a shaker model THZ-82 shaker, manufactured by Changzhou Guohua Electronic Appliance Ltd, China, at a speed of 180 r/min for 7 days at 30ºC .Then, fifty milliliters (50 mL) of the medium were quantitatively added into a 100 mL of culture medium (250 mL flask).After which, the medium was shaken again at a speed of 180 r/min during 7 days at 30ºC.This procedure was repeated 3 times.
Then, the culture medium solution was taken and streaked repeatedly 3 times on the plate, after which the strains were added and the plate was introduced in the refrigerator using a slant culture.
In this work the concentration of petroleum hydrocarbons was determined using a non dispersive infrared oil instrument [6] .Bacteria count was performed by the plate counting method [7] .The operational and performance parameters used for the evaluation of bioremediation included the concentration of TPH, removal efficiency (RE), and number of bacteria (CFU).

The degradation ability of petroleum-degrading active bacteria
In order to test the effect of oil-degrading active bacteria on oil removal, oil was added to the soil samples.After which, active bacteria were added to the contaminated soil samples.Two blank samples were needed here, one of which was sterilized and the other was nonsterilized.The sterilized blank sample was prepared by adding 0.2 wt% of mercury chloride into one of the oil contaminated soil samples.A control test was conducted, which consisted of a contaminated soil sample in the absence of active bacteria but containing the indigenous or native microorganisms samples.
Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 210 Fig 1 shows the relationship between oil removal efficiency and bioremediation time.The oil removal efficiency in the sample containing mercury (sterilized blank sample) chloride was approximately 9%.The oil material lost in the sterilized blank sample containing mercury chloride is attributed to oil volatilization and aerial oxidation.In the case of the blank sample containing only native microorganisms, the oil removal efficiency increased linearly during the first week and then it leveled off around 37% of oil removal.This indicates that the indigenous microbes contributed to the removal of 25% of petroleum hydrocarbon, compared to the removal efficiency of the soil sample containing mercury chloride.

Fig. 1. The biodegradation efficiency of the strains evaluated
The soil samples inoculated with SY 21 , SY 22 , SY 23, and SY 44 strains showed higher oil removal efficiencies.The removal efficiency of TPH reached up to 50% after 2 days of inoculation.The different strains inoculated in the contaminated soil showed the same removal rate up to 40%.The isolated strains rapidly adapted to the environment efficiently degrading hydrocarbons compounds.Fig. 1 shows that the biodegradation action of all the petroleumdegrading active bacteria tested follow the same trend.Thus the degradation efficiency of TPH increased gradually, which indicates that the contaminated soil provides an appropriated environment for bacterial growth.Eighty percent (80%) of hydrocarbons were degraded during the first 8 days of bioremediation while the degradation efficiency of the blank sample was only 37%.It is clear that the hydrocarbons were degraded mainly by the petroleum-degrading active bacteria.Fig. 2 shows the variation of number of bacteria as a function of time.The number of bacteria increased gradually, as the bioremediation time progressed.The number of bacteria in the inoculated samples was higher that the number of bacteria in the blank sample.This indicates that the indigenous microbes were inefficient in degrading oil and that the inoculation of petroleum-degrading active bacteria shows potential in removing hydrocarbons contaminants.

Fig. 2. The number change of 7 bacteria
The strains evaluated showed different oil degradation capacity and different patterns.Fig. 3 presents the degradation rate of TPH by seven strains.It is observed that the rates of biodegradation of SY 21 , SY 22 , SY 23, and SY 44 were higher in the second day, while the rates of SY 42 and SY 43 were higher in day 4, while in day 6, the highest degradation rate was shown by strain SY 24 .The average degradation rates of TPH were within 0.01~0.1 g•kg -1 •d -1 , which are higher than degradation data previously reported [8][9][10] , consequently these strains could degrade TPH more rapidly.Previous work [11] using marine filamentous bacteria reported rates of biodegradation in the range of 7.92×10 -11 to 4.8×10 -10 mg•cell -1 •d -1 .Similarly, other work [12] using pseudomonas showed that the highest oil degradation rate was from 1.44×10 -10 to 3.77×10 -9 mg•cell -1 •d -1 .Fig. 4 presents the average degradation rate per cell of the seven strains used in this work.It shows that the highest degradation rate of 2.34×10 -3 mg•cell -1 •d -1 was obtained for the strain SY 43 , f o l l o w e d b y s t r a i n S Y 23 with a degradation rate of 1.50×10 -3 mg•cell -1 •d -1 .The degradation rate of the remaining strains ranged from 1.15×10 -3 to 4.57×10 -4 These results demonstrate that the rate of degradation shown by these strains is tens of thousands times higher than the degradation rate reported in previous work.Therefore, petroleum-degrading active bacteria show great potential for the bioremediation of TPH contaminated soils.

Effect of concentration of TPH in contaminated soil on the biodegradation efficiency of petroleum-degrading active bacteria
Four oil samples containing different concentrations of TPH were prepared.The concentration of TPH in mud samples 1, 2, 3, and 4 were 125mg.L -1 , 56 mg L -1 , 3245 mg.L -1 and 209 mg.L -1 , respectively.In each sample the volume of inoculum was also varied as follows: 2 mL, 5 mL, and 10 mL.Fig. 5 shows the number of bacteria and the removal efficiency (RE) of TPH observed in the mud samples during biodegradation.The number of bacteria increased as the volume of inoculum increased.Hence, the number of bacteria was enhanced by increasing the volume of inoculum.The removal efficiencies of TPH for sample 1 were 30%, 33%, and 70% for the corresponding inoculum volume of 2 mL, 5 mL, and 10 mL after 17 days of biodegradation.In addition, the RE of TPH of sample 2 was 20%, 42%, and 45% and the corresponding RE of TPH of sample 3 was 33%, 38%, and 45%.The petroleum removal efficiency in sample 4 was 43%, 80%, and 81%.These results indicate that the higher the inoculum volume the higher the RE of TPH.The number of bacteria and RE of TPH for the soil samples were low when the inoculum volume was 2 mL.However, when the inoculum volume was increased from 2 mL to 5 mL the removal efficiency of TPH increased.The RE of TPH was similar when the inoculum volumes were 5 mL and 10 mL, respectively.This performance might indicate that a high inoculum volume enhances the competition ability of petroleum-degrading bacteria in relation to native microorganism.It could also aid the quick bacterial adaptation to the environment, which also increases the TPH degradation efficiency.

Bioremediation of oil-contaminated soil by petroleum-degrading active bacteria
Figure 6 shows that significant removal of TPH took place in the soil samples inoculated with petroleum-degrading active bacteria compared with the removal of TPH in the blank sample.After 6 days of bioremediation, the percentage of TPH removal in the samples inoculated with bacteria was 17.2% and 19.2 % for SY 43 and SY 23 respectively; while the percentage of TPH removal in the blank sample was only 1.4%.At day 9, the removal efficiency of SY 43 was 30.5%, which was higher than the removal efficiency observed for the strain SY 23 (24.9%).Fig. 6.TPH concentration and TPH removal efficiency (RE) as a function of bioremeditation time.
After 12 days of bioremediation, the TPH concentration of the sample having the strain SY 43 declined to 213.3mg•kg -1 and the RE of TPH was 81.1%; while the TPH removal efficiency of the sample containing the strain SY 23 and in the blank sample were 60.3% and 25.6%, respectively.After 18 days of inoculation, the removal efficiency in the three samples climbed up to 88.4%, 73.4%, and 37%, respectively.These observations indicate that the contaminated samples inoculated with petroleum-degrading active bacteria had higher oil removal efficiency than in the blank sample.The average degradation rates of TPH by SY 43 and SY 23 was 0.044 g•kg -1 •d -1 , 0.034 g•kg -1 •d -1 respectively; while the corresponding average degradation rate of the cells was 2.14×10 -6 mg• cell -1 •d -1 and 1.64×10 -6 mg• cell -1 •d -1 respectively.Figure 6 shows that the petroleum removal ability of SY 43 is higher than that of SY 23 .Fig. 7 presents the number of bacteria during the bioremediation process for the strains SY 43 , SY 23 , and the blank sample.The number of bacteria in the inoculated soil samples was 100 times bigger than the number of bacteria in the blank sample.The number of bacteria in the soil sample inoculated with SY 43 was higher than the number of bacteria in the soil sample inoculated with SY 23 .Thus, the number of petroleum-degrading active bacteria in the contaminated soil sample seems to be the main factor improving the bioremediation of the soil.The results show that both SY 43 and SY 23 could rapidly degrade TPH in the contaminated soil.The TPH degradation efficiency showed by the strain SY 43 was better than the degradation efficiency achieved by the strain SY 23 .

Conclusions
1.The bacteria strains isolated from petroleum contaminated soil in the north region of the Shaanxi province were Acinetobacter SY 21 , Neisseria SY 22 , Plesiomonas SY 23 , Xanthomonas SY 24 , Azotobacter SY 42 , Flavobacterium SY 43 , and Pseudomonas SY 44 .2. The TPH removal efficiency of these bacteria strains was 50% after 5 days of testing and 80% after 8 days of bioremediation.The average cell-degradation rate and the removal rate of TPH were thousand times higher compared to previously published results.3. The number of active bacteria increases as the amount of inoculum increases, which enhances the competition ability of petroleum-degrading active bacteria against native bacteria.Simultaneously, this competition forces native bacteria to rapidly adapt to the environment improving their degradation ability, though, the bacteria strains show different petroleum removal trends even when the same inoculum amount was added, the average TPHs degradation rate was almost the same and the average degradation rate increases as the TPHs in contaminated soil increases.4. Strains SY 43 and SY 23 show rapid degradation of TPH in contaminated soil.However, the degradation efficiency of SY 43 was higher than the degradation efficiency of SY 23 .

Summary
The growth characteristics of 7 strains isolated from oil contaminated soil, as well as their respective degradation efficiency for various hydrocarbons were investigated.Factors that can impact biological oil degradation efficiency were revealed in a series of experiments.
The results indicate that isolated strains could rapidly degrade crude oil, showing high activity in the first 13 h of bioremediation.These strains could grow in paraffin wax, which indicates that these strains could degrade long chain hydrocarbons.Some of them (SY 22 , SY 23 , SY 24 , SY 42, and SY 43 ) were able to use short chain hydrocarbons and aromatic hydrocarbons as substrate, so these five strains are the preferred ones for the bioremediation of oil contaminated soil.Suitable pH for the growth of these five strains was in the range from 7 to 9. NH 4 NO 3 and oil concentrations should range from 1000 mg/L to 1500 mg/L in order to achieve optimum conditions for petroleum hydrocarbon degradation.Adding organic matter such as starch and glucose accelerated oil and PAH degradation capability of the strains SY 22 , SY 42 , and SY 23 strains.The presence of metal ions, such as Ni 2+ and Co 2+ , in soil decreased the crude oil degradation efficiency of these strains, while metal ions, such as Fe 2+ and Mn 2+ , did not affect the oil degradation activities.
Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 216

Introduction
Eight million tons (Mt) of petroleum is spilled into the environment every year worldwide.In China, 0.6 Mts of petroleum enters into soil, groundwater, rivers and ocean every year.Oil contamination is a severe threat for our environment and thereby attracts general concern.Consequently, the remediation of oil polluted sites has become an important issue worldwide.
Bioremediation has become one of the most promising technologies for soil remediation, because the cost of remediation of petroleum contaminated soils by biological techniques is low; in addition to the fact that through bioremediation the complete removal of oil can be achieved; while no secondary pollution is introduced.Microorganisms used for bioremediation are usually grouped as indigenous and exogenous microbes.The addition of nutrients increases the activity of native microorganisms, however bioremediation is boosted with the addition of exogenous bacteria.Native microbes need a long time to domesticate, and thereby show low growth rates and low metabolic activity, which make decontamination slow and ineffective.Therefore, the application of bioremediation using indigenous microbes is restricted.Thus, the screening of petroleum-degrading active bacteria to remediate oil polluted soil is a necessary task.In this experimental work, several strains (seven) were isolated from oil contaminated soil in the north region of the Shaanxi province.The effect of pH, nutrition (nitrogen and phosphorous), and pollution intensity on the oil degradation efficiency of the isolated strains were investigated.Furthermore, based on the complexity of the soil systems, the degradation capacity of the isolated bacteria of different kinds of petroleum hydrocarbons and the effect of adding organic co-substrate and metal ions on the bioremediation were studied.

The Source of samples
The tested crude oil and petroleum polluted soil were collected at oil wells in the northern region of the Shaanxi province.The strains separated from the oil contaminated soil were SY 21 , SY 22 , SY 23 , SY 24 , SY 42 , SY 43 , and SY 44 [13] .

Culture medium
The recipes of the different culture media used in this work are provided as follows.
Recipe of liquid or solid beef grease & peptone cultivation medium: 10 g of peptone, 3 g of beef grease, 5 g of NaCl, 1000 mL of distilled water, pH 7.0.The medium can be solidified using 20 g of agar.

Strains separation
Crude oil was added into the soil collected in the north region of the Shaanxi province intermittently, to progressively increase the oil concentration in the soil, so as to obtain bacteria with high capacity for oil degradation.The process was carried out at aerobic conditions under continuous shaking.Temperature was controlled at 30 o C. Pure strains were isolated 21 days later by streaking them repeatedly on a plate.
The separated strains were identified to the genus level depending on their morphological and physiological-biochemical characteristics in general ways.
The preparation of the bacterium suspension was carried out by inoculating the strains into liquid beef grease & peptone medium, which was pre-sterilized under 121 o C for 30min.The mixture of medium and bacteria was shaken for 36 h (180 r/min) under 30 o C. Later, the mixture was centrifuged (180 r/min) and the resulting suspension was discharged while the residual sediment was washed 3 times using phosphate buffer.Finally, the washed sediments were diluted using phosphate buffer in order to adjust the number of the cells in bacterium suspension to be 1×10 8 .

Study on the growth characteristics of the strains
Under sterile conditions, strains were inoculated in 200 mL liquid beef grease & peptone medium, which had been previously sterilized.Then the mixture of bacteria and medium was shaken at 30 o C and 180 r/min.Afterwards, optical density D 460 of the bacterium liquid using light (460 nm wavelength) was measured at regular intervals.

Determination of petroleum hydrocarbons
Oil degrading strains were inoculated into the crude oil medium, which was previously sterilized.This mixture was shaken and the pH adjusted below 3.Then, the medium was placed into funnels, shook and the total volume brought to 100 mL after adding 20 mL of CCL 4 in order to extract the hydrocarbons present in it.This mixture was kept static for segregation to take place (layered).The under layer was filtered and dried using anhydrous sodium sulfate and then it was placed into a 50 mL volumetric flask.The upper-layer was extracted using CCL 4 twice, then filtered, and placed into a 50 mL volumetric flask.The concentration of petroleum hydrocarbon was determined using a non dispersive infrared oil analyzer and the biodegradation of petroleum hydrocarbon  was determined using the following equation (1).
In this equation ( 1), 0 c and c x represent the residual concentration of petroleum hydrocarbon in blank samples and the test samples, in mg/L; respectively.

Strains' hydrocarbon degradation efficiency tests
Six hydrocarbon compounds which included normal octane, paraffin wax, benzene, methylbenzene, phenol, and naphthalene were added to the inorganic medium that was Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 218 previously sterilized 121 o C for30 min using high pressure steam.Then, 5 mL of bacterium suspension were added to the medium.This mixture was shaken for 36 hours under 30 o C and 180 r/min.After all the phenol was evaporated from the mixture, the bacterium suspension was added.Naphthalene mixed with acetone was also added into the bacterium suspension after all the acetone was evaporated from the mixture.Finally, the optical density D 460 of the culture solution under 460nm was measured and the concentration of petroleum hydrocarbons was determined at regular intervals.

Evaluation of the factors influencing the activity of petroleum-degrading bacteria
Crude oil samples were mixed with petroleum ether to prepare a solution having a concentration of 60 g of crude oil/L of solution.Then, the mixture was filtrated using a 0.25 m filter membrane.The filtrate was placed into a flask and the petroleum ether was completed evaporated from the flask.Then, pre-sterilized inorganic medium and 5 mL of bacterial suspension were added into the flask.Using this oil-contaminated soil samples as the starting point, several petroleum degradation experiments were performed at different conditions of pH, organic load, nitrogen source, carbon source and metal ions.

Isolated strains cultivated in hydrocarbon medium
Table 2 shows bacterial growth, bacterial density, and the rate of oil biodegradation reached by each strain after 7 days of cultivation.The strains grew well in oil media and emulsified crude oil.The density of bacteria after 7 days of cultivation was observed to range between 110 7 /mL and 110 9 /mL.These results indicate that the strains used petroleum as the carbon source.The biodegradability () after 7 days of cultivation was between 43.8% and 58.9%, which exceeded the biodegradability of formerly reported petroleum-degrading bacteria B01(25.8%-32.8%) [11]and were close to that of O-8-3 Pseudomonas, marine bacteria SJ-06W, SJ-6, and SJ-16A-2 as previously reported [14] .

The growth trend in liquid medium
Figure 8 shows bacteria growth as a function of time.The curves in Fig. 8 indicate that bacteria grow rates were low during the first 13 hours, after which the bacteria grow rates followed a logarithm growth period during the next 13~23 hours; and then turned into a slow down growth period during the following 23~40 hours.Finally, bacteria began to die after 40 hours of activity.Thus, the strains showed the highest activity during the 13 to 23 hours of life.
Fig. 8. Growth trend of the seven isolated strains in liquid cultivation medium

Growth trend in agar medium
Figure 9 shows the growth trend of the same 7 strains in agar media.
Fig. 9 shows the variation of the diameter of colony forming of the different strains as a function of time.The colonies of SY 21 were formed after 4 hours of activity.After 9.2 hours the diameter reached 4 mm.This colony expanded continuously in the first 20 hours during which the average growth rate was 12.84 mm/d.In addition the colony growth was circular having an ivory-opaque color with an arid and disordered surface.The SY 22 strain formed a circular ivory and semitransparent colony after 4 hours of inoculation.The surface of the colony was wet and orderly with a diameter of 3 mm after 9.2 hour.Similar to the previous case, the colony expanded continuously within the first 20 hours with an average growth Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 220 rate of 8.41 mm/d.The colony formed by the strain SY 23 was ivory and opaque with an arid and disordered surface.The SY 23 colony was formed after 9.2 hours reaching a diameter of 2 mm after 15 hours.This colony also expanded continuously with an average growth rate at 2.49 mm/d.The SY 24 formed an opaque and creamy yellow colony after 4 hours of inoculation.Its surface was flat and disordered, and the colony expanded continuously during the first 37 hours at a growth rate at 8.43 mm/d.After inoculation the strain SY 42 formed a white transparent and circular colony.The surface of the colony was wet and orderly.The average growth rate of this colony was 5.30 mm/d.The colony made up by the SY 43 strain was white-transparent and disordered with a wet and smooth surface.The average growth rate of this colony was 5.30 mm/d.The SY 44 strain formed an ivory semitransparent circular colony.Its surface was wet, smooth, and orderly and reaching a diameter of 4.2 mm after 4 hours.The colony expanded continuously during the first 15 hours with an average growth rate of 24.32 mm/d.The average growth rate of the 7 isolated strains ranged from 2.49 to 32.4 mm/d.Fig. 9. Growth tendency of seven isolated strains in agar cultivation medium

The degradation ability of petroleum-degrading active bacteria toward different types of hydrocarbons
The majority of petroleum-degrading bacteria can degrade only few kinds of hydrocarbons [15][16] .The middle-chain and long-chain normal alkane can be degraded by most petroleumdegrading bacteria.However, the short-chain hydrocarbons and aromatic hydrocarbons can only be degraded by few petroleum-degrading bacteria.For the majority of bacteria it is difficult to digest short-chain and aromatic hydrocarbons, which can even be toxic.
In this work, the hydrocarbon degradation capability of the 7 strains was evaluated using the following hydrocarbon compounds: octane, paraffin wax, benzene, methylbenzene, phenol, and naphthalene.The initial concentration of these hydrocarbon compounds were 125 mg/L, 64800 mg/L, 200 mg/L, 14.4 mg/L, 200 mg/L, and 330 mg/L, respectively.During these tests the temperature and pH were set at 30 o C and 7, respectively.
Table 3 shows that the seven strains grew in the paraffin wax media (The optical density D 460 measured range from 0.117 to 0.450).The degradation efficiency of paraffin wax shown by the SY 43 strain was 81.3%, which was the highest degradation efficiency observed, while the strain SY 21 showed the lowest efficiency at 43.7% degradation.The degradation efficiencies of the other strains were between SY 43 and SY 21 .All of these 7 strains showed a high degradation capability toward middle and long-chain alkane, as the 90% of paraffin wax consisted of C 18 C 61 normal and isomeric alkanes [17] .The degradation efficiencies of naphthalene by the 7 strains were about 40%.The SY 23 and SY 24 strains showed high abilities to degrade benzene, methylbenzene, and phenol as the degradation efficiency reached from 80% to 90%.The majority of these strains showed low degrading efficiency toward normal octane, with the exception of strains SY 24 and SY 43 , which showed degradation rates of 54.4% and 56.8% respectively.These observations indicate that the following strains SY

The effect of pH
In microorganisms, biochemical reactions are catalyzed by enzymes.It is well known that enzymatic reactions occur within a suitable pH range and microorganisms are sensitive to the alteration of pH.Thus, it is necessary to determine the optimum pH value suitable for petroleum degradation by bacteria.The pH value of soil normally ranges between 2.5 to 11.0.Thus, before the inoculation of strains into the crude oil media (petroleum concentration was fixed at 600 mg/L), the pH value was adjusted to 3, 5, 7, 9, and 11 for each medium.The experiments were carried out at a rotation speed of 180 r/min for 96 hours at 30 o C.After which, the concentration of petroleum hydrocarbon was determined and the degradation efficiency was calculated.Figure 10 shows the degradation efficiency of 4 of the strains.4 summarizes the degradation efficiencies of the strains.The observations in Table 4 indicate that the hydrocarbon degradation efficiency shown by these strains exceeded 60% when the mass concentration of petroleum hydrocarbon was 1000 mg/L.The hydrocarbon degradation efficiency shown by the SY 24 strain was reduced when the mass concentration of petroleum hydrocarbon increased to 1500 mg/L.The hydrocarbon degradation efficiency of all the strains was reduced when the mass concentration of petroleum hydrocarbon was increased to 3000

Effect of different nitrogen sources
In order to determine the impact of the nitrogen source on the strain degradation efficiency, a series of different nitrogen sources were used in addition to NH 4 NO 3 (200 mg/L) in the inorganic media.The concentration of the different nitrogen sources was set as 350 mg/L.The rotation speed was set at 180r/min for 96 hours at 30 o C and at pH of 8.0.After 96 hours of inoculation the concentration of the residual petroleum was determined.Table 5 presents the hydrocarbon degradation efficiency as a function of nitrogen source.Table 5 indicates that all the strains showed the highest degradation efficiency when NH 4 NO 3 was used as the nitrogen source, while the lowest degradation efficiencies were observed when NaNO 3 was used as the nitrogen source.This indicates that NH 4 NO 3 is the best nitrogen source for the strains under evaluation, which is in agreement with the results presented by other researchers [18] .It is important to mention that the SY 23 strain showed a high degradation efficiency when (NH 4 ) 2 SO 4 and Urea were used as nitrogen sources, which points out that SY 23 could be used for remediation situations were these nitrogen sources are readily available.

Effect of different carbon sources
Glucose and starch were used as co substrate in the inorganic medium in which petroleum concentration was fixed at 1000 mg/L.These experiments were carried out at a rotation speed of 180 r/min for 96 hours at a temperature and pH of 30 o C and 8.0, respectively.
Table 6 shows the effect of dosing co substrate on the removal efficiency of petroleum.Table 6 shows that the degradation efficiency of petroleum hydrocarbon by the SY 22 and SY 23 strains increased from 43.8% and 17.6% to 71.5% and 70.2%, respectively.These results show that the strains degradation efficiency was enhanced by the use of glucose and starch as carbon sources.The explanation is that glucose and starch can be used as co-metabolism medium during the petroleum degradation process [19] .The SY 22 and SY 42 strains had high degradation efficiency of naphthalene (42.6% and 40.8% as showed in Table 3), these efficiencies were improved after adding glucose and starch.The SY 23 strain also showed high degradation efficiency of benzene, methylbenzene, and phenol with corresponding efficiencies of 90.5%, 84.7% and 90.5%.These observations indicate that the SY 23 strain can degrade PAH in crude oil and that the degradation efficiency can be increased to a large extent after adding starch.Thus, bacteria activity can be improved by adding the Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 224 appropriate carbon sources, in this case glucose and starch.It has been previously reported that using glucose as carbon source improves the degradation efficiency of PAH and if glucose is fed intermittently the abilities of bacteria to degrade petroleum hydrocarbon could be maximized [20] .

Effect of different metal ions
The concentration of metal ions increased in oil fields due to the aging and mineralization of soil during the weathering process of petroleum contaminated soil.In order to find the impact of the presence metal ion on the biological removal of petroleum, metal ions of Fe 2+ , Mn 2+ , Ni 2+ , and Co 2+ were added into the inorganic salt liquid media in which the petroleum hydrocarbon concentration was 1000 mg/L.
The experiment was carried out at rotation speed of 180 r/min for 96 hours at 30 o C and a pH of 8.0.Table 7 shows the calculated petroleum removal efficiencies and it clearly shows that the degradation efficiency of the strains declined significantly after adding Ni 2+.It seems that a high concentration of Ni 2+ restricted the activities of the microorganisms.For instance, the degradation efficiency of SY 43 strain was decreased from 53.3% to 10.9%.In contrast, adding Fe 2+ improved the degradation efficiency of petroleum hydrocarbon (SY 21 and SY 23 strain).However, the activity of SY 43 strain was restricted.After adding Mn 2+ the degradation efficiency of oil by SY 23 strain was enhanced by 12% while the degradation efficiency by SY 21 and SY 43 strain was not affected.The degradation efficiency of oil achieved by the SY 21 and SY 43 strains decreased 16% and 12% respectively after adding the metal ions of Co 2+ .These results point out that the addition of metal ions such as Fe 2+ and Mn 2+ has a favorable influence on the oil degradation efficiency.On the contrary, the degradation efficiency of petroleum hydrocarbon was decreased after adding metal ions such Ni 2+ and Co 2+ .was used as a nitrogen source in contaminated soil containing oil concentrations ranging from 1000 mg/L to 1500mg/L.6.The degradation efficiency of strains SY 22 , SY 42 , and SY 23 is significantly enhanced by the addition of starch and glucose.7. The presence of metal ions such as Ni 2+ and Co 2+ in the oil contaminated soil decreases the strains degradation efficiency, while the presence of Fe 2+ and Mn 2+ does not affect the oil degradation by the strains, on the contrary might improve it.

Part III Bioremediation of oil contaminated soil by SY23 petroleumdegrading active bacteria -Impact of bulking agent and tillage on bioremediation of petroleum-contaminated soil 4.1 Summary
The impact of adding bulking agent and tillage on bioremediation of petroleum contaminated soil was studied.The results showed that the strain degradation efficiency of TPH was 76% in 48 days after adding bulking agents and tillage.This degradation efficiency was 15% higher than the degradation efficiency in the control experiment in which bulking agent was not added.Meanwhile, the degradation rate was 2.34 times higher in the sample containing bulking agent compared to the control sample.The addition of bulking agent increased water content in the soil as the bulking agent absorbed water, which improved the degradation of TPH.Gas chromatography-Mass Spectrometer (GC-MS) analysis indicated that the peak numbers of the GC profile decreased from 32 to 14 in 64 days after adding bulking agent.This result indicated that branched alkanes, alkene, carotane, and alkylnaphthalenes were thoroughly degraded.The peak numbers of the GC profile decreased 10 times.Furthermore residual hopanes and steranes were also thoroughly degraded after the combined treatment of the oil contaminated soil with bulking agents and tillage.The degradation efficiency of TPH decreased as tillage times decreased, the optimum tillage frequency was once per day with a shovel.

Introduction
Petroleum could lead to the contamination of ground water after petroleum sprays into soil.Bioremediation of petroleum hydrocarbon contaminated soil is considered a new technology with a broad prospect because of its low-cost [9] .During in situ bioremediation, Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 226 sufficient dissolved oxygen (DO) is necessary to keep the degradation activity of bacteria.It has been reported that the mineralization of TPH in soil will be restrained when the DO concentration is lower than 15% (dry soil) or 5% (wet soil) [21] .Tillage is a mechanical way to improve the local environment in the soil.This method can change the physico-chemical characteristic of soil and stimulate the activity of bacteria by increasing the oxygen content in the soil and aiding the release of carbon dioxide [22,23] .Bulking agents are cheap low density materials.The addition of bulking agents into the soil reduces the density, increases the porosity, and enhances the spread rate of oxygen in the soil [24] .This research evaluates the impact of adding a bulking agent and tillage on the bioremediation of petroleumcontaminated soil.

Samples source
Oil contaminated soil samples were collected at contaminated sites surrounding oil wells from an oil field located in the northern region of the Shaanxi province, China.The samples were homogenized, sieved (pore size 2 mm), and stored in a dark and ventilated fridge at 4°C until use.

Microbial inoculations
Petroleum degrading active bacteria were collected from oil contaminated soil samples [25] .The solid SY 23 strain was obtained as a concentrated bacteria suspension that was separated by centrifuge.The solid bacterial product was prepared after the solid SY 23 strain was dried on sterilized condition at 37 o C for 48 hours.

Processing methods
In order to prepare a bacterial-rich suspension, certain amount of the solid bacterial product was added into a bacteria-free buffer.A substrate medium was added into the bulking agent to prepare a mixture.Later, the mixture was sterilized.Then, the bacterial-rich suspension was mixed with the bulking agent mixture which was cultured for 24 hours.The final product was ready for addition into the petroleum contaminated soil.

Analytical methods
The petroleum hydrocarbon (TPH) composition was determined using an OCMA -350 nondispersive infrared oil analyzer.Oil components were measured using a gas chromatograph (Model Trace 2000) and a Mass Spectrometer (Ms) model Voyager 5975B, manufactured by Agilent USA.The GC was equipped with a 30 m long capillary (DB-5) in which the stationary phase was 0.25 μm thick.The measurable range of relative molecular weights was 30 to 450.GC conditions for analysis were as follows: carrier gas: helium (0.8 mL.min -1 ); Flame Ionization Detector (FID) temperature: 320 o C; the initial temperature was 40 o C and it was maintained for 5 minutes.Then, the temperature was increased to 300 o C at a speed of 10 o C /min.Conductivity meter was used to measure conductivity and pH test paper was used to measure pH values.The conductivity and pH values must be analyzed under the conditions where the ratio of bulk factor of soil to water was 1:5(W/V) [8] .Finally, constant weight method was used to measure moisture content.

Design of the experiments
The objective of the experimental design was to investigate the bioremediation of petroleum hydrocarbon contaminated soil by bioaugmentation products through bioremediation simulation tests with the addition of bulking agent and tillage.The experiments were carried out in basin ports having diameters of 15 cm and depths of 15cm.A mass of 1000 g of soil was used in each group.Table .8summarizes the experimental conditions.Each experimental group was conducted in triplicate.Experiments were carried out at room temperature, which varied in the range of 16 to 20 o C. Samples were taken for analysis at time intervals to measure pH, conductivity, TPH concentration, and moisture content.The sample interval was increased when the rate of petroleum-degradation started to decrease.

The influence of bulking agent on the degradation of petroleum hydrocarbons
Figure 11 shows the experimental observations, and it indicates that the addition of bulking agent and tillage aid the reduction of petroluem concentration.Samples subjected to tillage had the lowest remaining TPH concentration.TPH concentration declined from 4.5 g/kg to 1.737 g/kg (57%) after tilling for 19 days with bulking agent.While, for sample BF without bulking agent only 23% of the TPH was degraded.The degradation rate in sample BF was only 0.968 g/kg.Thus, the removal rate of TPH was 2.34 times higher when bulking agent was added.The concentration of TPH in sample CF with bulking agent after 48 days of bioremediation had declined 3.044 g/kg (76%).Meanwhile the sample without bulking agent (BF) only declined 2.611 g/kg (61%).For the Stagnant samples with added bulking agent, the removal efficiency of TPH was 66.4% while the removal efficiency of the samples without bulking agent was only 50.9% after 48 days.These observations indicate that the addition of bulking agent accelerates the removal rate of TPH by bacteria.The bulking agent Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 228 increases the permeability of the contaminated soil so that the oxygen transfer rate and the water-holding capacity are also enhanced.This provides an advantageous condition for bioremediation of oil contaminated soil.Research conducted by Xiaomei Ye [26] showed that the concentration of TPH declined 70% after 120 days of degradation which is in agreement with this study.
Figure 11 indicates that the removal efficiency of samples AF, BF, and CF were 22%, 33%, and 67% respectively after tilling for 26 days.Meanwhile, the removal efficiency in those samples without tilling was 2%, 22%, and 56% respectively.It is obvious that tillage has increased the removal efficiency of TPH.Tillage not only raises the content of oxygen in soil but also accelerates the speed of substrate transfer from outside into the biomembrane.The oxygen concentration in soil has a significant effect on the degradation of TPH.During pure oxygen aeration, the release rate of CO 2 is 0.013 mol/d.However, the production of CO 2 is reduced to 0.004 mol/d during air aeration [27] .In addition, tillage separate the soil block into small ones and mixes the soil.Therefore, tillage causes redistribution of C, N, and water in the contaminated soil.It has been reported [28] that tillage improves the removal efficiency of tetrachloroethylene and trichloroethylene in contaminated soil.Fig. 11.Influence of bulking agents on the degradation of TPH from oil-contaminated soil that was (A) left stagnant, (B) tilled once every day

Changing patterns of the oil component with bulking agent
In order to understand the way bulking agents work, extractions of soil samples after degradation for 64 days were analyzed by GC-MS.Table 9 and Figure 12 summarizes the results of the GC-MS.Fig. 12 indicates that the removal efficiency of oil components in the samples with bulking agent were higher than in the blank sample.Comparing the GC-MS spectrum for sample AJ (bulking agent-free) with sample BJ (with bulking agent added), which were left stagnant for 64 days, 32 peaks were shown in the AJ soil sample (bulking agent-free) spectrum while the BJ showed only 14 peaks in the GC-MS.The branched alkanes, alkene, carotane and alkylnaphthalenes in sample BJ (containing bulking agent) were thoroughly degraded.But the removal rate of branched alkanes, alkene, carotene, and alkylnaphthalenes in sample AJ (bulking agent-free) were 57.2%, 67.8%, 68.8%, and 79.7% respectively.The addition of bulking agent promotes the growth rate of the active bacteria because bulking agent keeps water in the soil and aids oxygen transfer.So the removal rate of normal paraffin, hopanes, and steranes could also be promoted under these conditions.
After combined treatment of addition of bulking agent and tillage, 10 peaks in the GC-MS spectrum disappeared and residual branched alkanes, alkene, carotene, alkylnaphthalenes, hopanes, and steranes were also thoroughly degraded.As well as the removal of 99.7% of normal paraffin.Adding bulking agent promotes the interaction between bacteria and TPH.Likewise, the combined treatment with bulking agent and tillage demonstrate improved bioremediation.

Influence tillage times on the degradation of TPH
Figure 13 shows the experimental matrix designed to explore the influence of tillage time and the addition of bulking agent on the degradation of TPH.In the samples evaluated the change of TPH followed the same trend.TPH concentration decreased as a function of time with the removal rate increasing gradually.TPH content in sample F1 (tilled once a day) was the lowest since day 3, followed by samples F2 and F3.The biodegradation level in sample F0 (without tillage) was the worst.The removal efficiency of TPH in F1 was up to 92.64% while the removal efficiency in samples F2, F3, and F0 was 80.46%, 69.14%, and 60.26% after 36 days of biodegradation.Likewise, the removal efficiency of TPH decreased as tillage times decreased.The optimum tillage frequency was once a day every day using a shovel.If economic factors are considered, then a minimum of once tillage each 3 days would be acceptable.Fig. 13.Influence of tillage times on the degradation of TPH in oil-contaminated soil Previous reports, including EPA [29] , indicate that the degradation of oil contaminants by indigenous bacteria follows a first order reaction, that is expressed by the following equation: In equation ( 2), C represents concentration of TPH in the soil in mg‧kg -1 ; K T represents substrate removal constant in d -1 ; and t represents degrading time in days.
A plot of lnC as a function of time results in a linear regression with lnC 0 as the intercept and K T as the slope.Then, the half-life time of the petroleum contaminant in the soil can be calculated as t 1/2 =ln2/K T , as shown in

Discussion
To explain how the removal efficiency of TPH is increased by the addition of bulking agents, pH, electric conductivity, and soil moisture were analyzed.The samples under evaluation had almost the same pH ranging from 6.0 to 6.7 during the evaluation period.Similarly, the electric conductivity in the samples ranged from 200 to 300 s/cm during testing, with the exception of water content, which was different for the samples tested.Figure 14 summarizes the results.Fig. 14.Influence of bulking agents on water content of oil-contaminated soil that was (A) left static, (B) tilled once every day Fig. 14 displays the curves of water content of the oil-contaminated soil sample that was left stagnant and for the samples that were tilled once every day.The experimental observations revealed that although the dose of water was the same for all the samples, the water content in the samples was quite different.The water content of the samples containing bulking agent was kept in 20% while the content of water in the blank sample was only about 15%.The bulking agent or saw dust shows high capacity for water absorption.The water saturation rate in these samples is very fast, with saturation times of just 3 min.The water absorption capacity of saw dust is 4.45 times bigger than its own weight [30] .In the samples containing saw dust, it was observed that the saw dust absorbs the water as soon as it is dosed into the sample.However in the case of the samples free of saw dust, water added would transfuse along the holes in soil.So that the water content in the blank sample (saw dust-free) is lower than in the samples containing saw dust.Furthermore, Figure 14(B) indicates that during the evaluation period, in the tilled samples without saw dust, the content is unstable, which can be explained by the fact that in this sample, tillage accelerates the speed of water evaporation.Saw dust retains the water in the soil, in addition to enhancing the air permeability in the contaminated soil sample which benefits the degradation of TPH by bacteria.

Conclusions
1. Adding bulking agent enhances the retention of water and the air transfer in the soil.
Experimental results show that the degradation efficiency of TPH was 76% in 48 days after adding bulking agents and tillage, which was 15% higher than the degradation efficiency in the samples without bulking agent.Likewise, the degradation rate is 2.34 faster in the samples containing bulking agent that in the samples without bulking Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 232 agent.GC-MS analysis indicates that the peaks (concentration) of the pollutants in the GC spectrum decreased from 32 to 14 in 64 days after bioremediation of adding the bulking agent.2. Tillage not only raises the content of oxygen in the soil but also accelerates the speed of transfer of substrates from outside into the biomembrane.The removal rate of TPH in samples that were tilled was 1.2 times higher than in the samples without tillage.Especially the concentration peaks of the pollutant components in the GC spectrum decreased 10 times after 64 days of degradation.Similarly, residual branched alkanes, alkene, carotene, alkylnaphthalenes, hopanes, and steranes were also thoroughly degraded after the application of the combined treatment with bulking agent and tillage.The degradation efficiency of TPH decreased as tillage times was decreased; the optimum tillage frequency is once every day with a shovel.

Summary
The influence of bioaugmentation products dosage and temperature on bioremediation was studied.The results showed that the degradation rate was related positively to the amount of inoculation.When the inoculums dose was increased to 0.6 mg.kg -1 the degradation efficiency of petroleum hydrocarbon (TPH) increased to 87% in 48 days.The results of GC-MS indicated that the petroleum constituents in the oil-contaminated soil were 82.7% nalkane, 16% alkene and the balance corresponded to others hydrocarbons, such as carotane, alkylnaphthalenes, hopanes, and steranes.The concentration peaks in the GC spectrum decreased from 32 to 14 within 40 days of bioremediation.This result indicated that branched alkanes, alkene, and alkylnaphthalenes were thoroughly degraded.However, linear alkanes chains, hopanes, and steranes were still remaining in the soil.In addition, the longer n-alkane chains were degraded with relatively higher rate, leaving the shorter part of the n-alkane as the residual fraction at the end of the bioremediation test.Moreover, it was observed that the concentration of residual n-alkane (short chains) decreased as the inoculation volume increased.This indicates that an increase in the amount of bioaugmentation products into the contaminated soil clearly improves the biodegradation efficiency.It was also determined that temperature has an important on degradation efficiency.For instance it was observed that at 30 o C, the concentration of TPH in the soil sample was reduced by 80%, whereas at a temperature of 20 o C, the removal efficiency of TPH was only 60%, which indicated that higher temperatures favors TPH degradation and accelerates bioremediation.

Introduction
As the development of the petroleum industry in China increases, soil contamination by petroleum products also increases in both: areal extension and concentration.Common pollutants in the contaminated soil are hydrocarbon compounds such as: benzene, methylbenzene, and dimethylbenzene, which are highly toxic and some of them may be carcinogenic.These hydrocarbons could be difficult to degrade after entering the soil [1] .Furthermore, once these pollutants are established in the soil, they could enter into the surrounded underground water and river basins.Bioremediation of petroleum hydrocarbon contaminated soil is considered a new technology with a broad prospect because of its low-cost and pollution-free characteristics.Previous research has focused on the stimulation of the activity of the indigenous microorganisms by adding nutrient substances such as nitrogen (N) and phosphorous (P) [3] .However, bioremediation would be restricted by the slow-growth rate and limited amount of the indigenous microorganisms, which can be overcome through the addition of active microorganisms that can easily adapt to the contaminated soil environment.Several studies on this issue have been published.For example, a patented technology by the BGI (Baltic General Investment Corporation, USA) promotes the degradation rate of petroleum hydrocarbons by using mixed microorganisms [4] .Wilson (1993) [31] also reported some strains which quickly degrade PAHs.Xiao-Fang (2007) [32] found that exogenous microbes increase the degradation of petroleum contaminated soil.Another research [33] s h o w e d t h a t b y splashing bacteria into the petroleum contaminated soil, with oil content ranging from 5% to 45%, degradation rates reached up to 90% after 150 days of testing.The addition of petroleum-degrading active bacteria and microbial inoculation into petroleum contaminated soil is an in-situ bioremediation technology which has been wildly investigated.Efficient bioremediation have been obtained by the application of microbial inoculation-formulations, which have been recently developed, into actual bioremediation projects [34] .This section of the chapter summarizes the influence of bioaugmentation dosage, dosage sequence, and temperature on the bioremediation of petroleum hydrocarbon contaminated soil and provides a theoretical foundation for practical applications.

Soil samples
The oil contaminated soil samples used in these experiments were collected from areas surrounding producing wells from an oil field located in the northern part of the Shaanxi province In China.The soil samples were free from additional dirt, pulverized, and well mixed before the experiments.

Microbial inoculations
Oil contaminated soil around oil wells was used to isolate bacteria which utilized crude oil as the only carbon source.Bacteria at hand in this oil contaminated soil samples were screened and separated and ranked as highly active petroleum-degrading bacteria [14] .The strain SY 23 , which is commonly reported in the literature [14] was separated under aseptic conditions that was then dried and sterilized at 37 o C for 48 hours.At this stage, the bioaugmentation product was ready for use.

Bioremediation methods
In order to prepare a bacterial-rich suspension, certain amount of the solid bacterial product was added into a bacteria-free buffer.A substrate medium was added into the bulking agent to prepare a mixture.Later, the mixture was sterilized and the bacterial-rich suspension was Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 234 mixed with the bulking agent mixture, which was cultured for 24 hours.The final product was ready for addition into the petroleum contaminated soil.

Analytical methods
The composition of the petroleum hydrocarbon (TPH) was determined by OCMA-350 nondispersive infrared oil analyzer.The concentration of the petroleum components was determined by GC-MS.A CG 7890, Model Trace 2000, was manufactured by Agilent was used and the mass spectrometer 5975, model Voyager, manufactured by Agilent was employed for the analyses.The GC was equipped with a 30m long DB-5 capillary, with a stationary phase of 0.25μm.The range of relative molecular mass was from 30 to 450, and the first 6.10 min corresponded to the solvent peak.The conditions of the GC analysis were: temperature was increased at a rate of 10 o C/min from 100 o C to 200 o C, and then the temperature was increased at rate of 5 o C/min up to 280 o C. The contact temperature between the Ms and GC was 250oC.Conductivity was determined using a conductivity meter and pH was determined using pH test paper.Finally, moisture content was determined by the constant weight method.

Design of experiments
An experimental matrix was designed to evaluate the effect of different inoculation schemes and dosage of bioaugmentation products on the bioremediation of petroleum hydrocarbon contaminated soil.The experiments were carried out in basin ports having a diameter of 15cm and depth of 15cm.In every group, 1000g of soil was used.Table .11summarizes the experimental observations.Each group was conducted by duplicate.Every group was turned over once a day and 20mL of water were added every day [35] .During this set of experiments, the moisture content in the environment was maintained at 18% using a humidifier.Samples were taken at constant time intervals for pH, conductivity, petroleum concentration, and moisture content analyzes.The sampling intervals were increased when the petroleum-degradation rate started to decrease.respectively.Figure 16 indicates that the TPH degradation rate after 8 days of biodegradation for the corresponding bacteria dosage conditions were 2%, 10%, 25%, and 40% respectively.While, the degradation rate of the blank sample without bacteria (CK) was only 3%.The TPH degradation efficiency during 48 days of testing was 47%, 68%, 79%, and 87%; while the degradation efficiency in the blank sample (CK) did not achieve even 20%.

Number
15. Residual TPH concentration in soil as a function of bacteria dosage and time.
16. TPH degradation rate as a function of bacteria dosage and time.
Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 236 Previous research [36] showed that the key problem of bioremediation by adding exogenous bacteria is how to solve the competition between exogenous and indigenous bacteria.Experimental observations show that exogenous bacteria survive well with the indigenous flora.As demonstrated through this experimental study, the TPH degradation rate in soil is positively related to the dosage of bioaugmentation products.The highest degradation rate was achieved when the bioaugmentation products dosage was 0.6 mg•kg -1 .Furthermore, at low dosage (0.01 mg•kg -1 ) of bioaugmentation products did rise significantly the degradation rate after 20 days of testing; due to exogenous bacterial growth.
Previous reports [37] indicate that the degradation of petroleum contaminated soil by bacteria can be described by a first order reaction: lnC=lnC 0 -K T .t A plot of lnC as a function of time renders a straight line with intercept lnC 0 and slope K T .The dynamic equations and the half-life of petroleum contaminants in soil were calculated using the following expression: t 1/2 =ln2/K T .Table 12 shows the half-life of the petroleum contaminants in soil as a function of bacteria dosage.Table 12 also shows that the TPH remediation cycle in soil is 300 days shorter than in the blank or control sample (CK).The substrate removal constant K T indicates that biodegradation increases as the dosage of bacteria increases while the half-life of the petroleum contaminants is reduced.The optimum dosage was 0.6 mg•kg -1 .

Number
Dose (mg To investigate the effect of microbial inoculums on the degradation of hydrocarbons, samples were subjected to extraction after 48 days of degradation.The composition of the extract liquors were analyzed through GC-MS.Fig. 17 shows the GC-MS spectra.The GC-MS spectra confirm that most of the petroleum constituents in soil were degraded by the microbial inoculums.When the dose was increased to 0.6 mg•kg -1 , the peak lines were almost parallel with the base line.Fig. 17 clearly shows that increasing bacteria dose improves TPH degradation and accelerates bioremediation. GC-MS indicated that the dominant petroleum constituents in the oil-contaminated soil were 82.7% n-alkane, 16% alkene, and the balance corresponded to other hydrocarbons, such as carotane, alkylnaphthalenes, hopanes, and steranes.Monocyclic benzene series were not found in the hydrocarbon analyzed, which is in agreement with Xiao-Fang's study (2007) [32] .13 indicates that branched alkanes and alkenes are easier to degrade than linear alkanes.The content of linear alkanes decreases as bacteria dosage increases.The degradation rate of linear alkanes was increased to 97.4% when the dose of bacteria was increased to 0.6mg•kg -1 .The residual components shown in Table 13 were mainly linear alkanes.

(%)
A(10 The hydrocarbon degradation rate was monitored when bacteria dosage was 0.2mg•kg -1 .Samples were taken for GC-MS analysis at the following degradation times: 0d, 4d, 8d, 40d, and 48d respectively.Fig. 18 and Table 14 show the experimental observations.Table 14 indicates that the peak values on the GS-MS spectrum are reduced after 4 days of bioremediation, which indicates that hydrocarbon biodegradation is taken place GC-MS analysis shows that 98.5% of alkenes were degraded, followed by 87.9% degradation of Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 238 linear alkanes and 41 % degradation of branched alkanes.The degradation rate of branched alkanes, carotene, and alkylnaphthalenes was increased up to 74.9%, 91.0%, and 100% respectively in 8 days of testing.At the same time the peak of the phytan (Ph, 2, 6, 10, 14tetramethylhexadecane) in the GC-MS spectrum, (shown by the arrows in Figure 18) almost disappeared.The Ph and Pristane (Pr, 2, 6, 10, 14-Tetramethylpentadecane) were not detected after 48 days of bioremediation.Thus, the presence of these components in the contaminated soil sample is taken as an indication of the biodegradation of the petroleum hydrocarbon in the contaminated soil.In Fig. 18, the peak of Ph could be seen in the CK line after 48 days of biodegradation.However, the Ph peak disappeared after inoculating bioaugmentation products.This is strong evidence that bioaugmentation products could degrade petroleum.The concentration peaks from the GC-MS spectra decreased from 32 to 14 after 40 days of bioremediation.This result points out that branched alkanes, alkene, and alkylnaphthalenes were thoroughly degraded.However, linear alkanes, hopanes, and steranes were left in the soil as pollutants.The residual part of the n-alkane corresponds to the short chains because bacteria degraded the longer n-alkane chains, which is in agreement with previous studies [37], which have reported that the degradation rate of nalkanes is reduced as the chain length increases.Previous work [37,38] claims that marine filamentous fungi have higher degradation capacity for eicosane, tetracosane, and hexacosane than bacteria.So, finding bacteria capable of degrading long chains of n-alkane is a key issue in bioremediation of petroleum hydrocarbon pollutants.The strain SY 23 in this experiment is a plesiomonas.Hydrocarbon biodegradation tests have shown that SY 23 bacteria have high capacity for degrading benzene, methylbenzene, phenol, and long chains of n-alkanes.During these experiments it was observed that the color of the raw contaminated soil changes from brown to yellow after the addition of bacteria; which could also indicate that biodegradation of petroleum hydrocarbon is taken place.Bioremediation rate could be increased if inoculation volume is increased.In addition, it was observed in Fig. 18.TIC of TPH concentration in soil during bioremediation this study that hopanes were not degraded during the first 8 days of testing, however it reaches 53% degradation after 40 days.This shows that hopanes are stabilized in the contaminated soil.In general, hopanes are hardly degraded if their concentration in the contaminated soil is too high.In this work, the concentration of hopanes was low (58mg/kg) and 60% of this concentration in the soil was removed.

The Influence of bioaugmentation product injection scheme on the degradation of petroleum hydrocarbon
Samples were divided into two groups A and B. In group A, the bioaugmentation products were injected all at once in one application.In group B, half of the bioaugmentation products were injected at the beginning of the test, and the other half was injected after 20 days of testing.The total bioaugmentation products in the two groups were the same.Three series of experiments were conducted for each group having a different concentration of the bioaugmentation products in each series as follows: 0.2 mg•kg -1 ,0.4 mg•kg -1 , and 0.6 mg•kg -1 respectively.Figure 19 summarizes the GC-MS results after 48 days of degradation.Figure 19 indicates that the value of concentration peak in the GC-MS spectra for group A was lower than for group B. The CG-MS results show that the main residual components were linear alkanes and hopanes.The peak area of the linear alkanes in group A was 170000, while the peak area of the linear alkanes in group B was 261000 when the bioaugmentation products dose was 0.2 mg•kg -1 .The peak area of the linear alkanes in group A was 81000 while the peak area of the linear alkanes in group B was 175000 when the bioaugmentation products dose was 0.4 mg•kg -1 , and finally the peak area of the linear alkanes in group A was 61000 while the peak area of the linear alkanes in group B was 142000 for a dose of 0.6mg•kg -1 .These observations indicate that the best sequence of bioaugmentation products application is to inject all products at once, which is in agreement with previous studies [39] .Thus, the addition of the total amount of bioaugmentation products aids the quick adaptation of the bacteria to the environment, that results in petroleum components removal efficiency.Injecting the bioaugmentation products in only one application degraded about 50% of TPH in the soil after 20 days of testing; while only 30% of TPH were degraded in group B. Degradation rates were 68%, 79%, and 87% when the concentration of the bioaugmentation products were 0.2 mg•kg -1 , 0.4 mg•kg -1 , and 0.6 mg•kg -1 respectively.In Group B, the late injection of the remaining half of the bioaugmentation products after 20 Introduction to Enhanced Oil Recovery (EOR) Processes and Bioremediation of Oil-Contaminated Sites 240 days of testing did not increase the degradation of TPH.Finally, in group A the degradation rates after 48 days of testing were 54%, 63% and 74%.

Influence of temperature on the biodegradation of petroleum hydrocarbon
Several studies [30] indicate that temperature is an important variable that determines the efficient degradation of petroleum hydrocarbon in contaminated soil.Two groups of experiments were carried out at two different temperature conditions.In the first group, the   20 presents the residual TPH concentration in the soil as a function of temperature and testing time.These experiments indicatd clearly the effect of temperature on TPH degradation.At 30 o C, the degradation of TPH reached 29.8% after 3days of treatment, whereas at 20 o C, the degradation of TPH reached only 7%.This indicates, that at higher temperatures, bacteria grow faster, which accelerates bioremediation.For the experiments conducted at 20 o C, the degradation rate of TPH increased rapidly after 10 days, which points out that the adaptation of bacteria in the low temperature environment took longer, which resulted in a total TPH degradation of only 60% at the end of the testing period.This overall degradation percentage (at 20 o C) was 20% lower than the total degradation of TPH reached in the experimental group conducted at 30 o C.

Conclusions
1. Exogenous bacteria survive quite well in the presence of indigenous flora.The degradation rate of TPH contained in the soil was related to the dosage of bioaugmentation products.In this work, the highest degradation rate was achieved when the dose of bioaugmentation products was 0.6 mg•kg -1 .2. GC-MS analysis indicates that the dominant petroleum constituents in the oilcontaminated soil were 82.7% n-alkane, 16% alkene, and the balance corresponded to of others hydrocarbons, such as carotane, alkylnaphthalenes, hopanes, and steranes.The height of the GC spectrum peaks decreased from 32 to 14 after 40 days of bioremediation; this indicates that branched alkanes, alkene, and alkylnaphthalenes were thoroughly degraded.However, linear alkanes, hopanes and steranes were left in the soil.Furthermore, long chains of n-alkane were degraded, while short chains of nalkane were left as residual hydrocarbon in the soil.It was determined that increasing inoculation increases the capacity of the bacteria to attack short chains n-alkanes.The application of bioaugmentation products into soil in one dosage significantly improved the biodegradation efficiency rather than the application of bioaugmentation products in several dosages.3. Temperature is the dominant variable that determines the efficiency of bioremediation of petroleum hydrocarbon contaminated soil.At higher temperatures, bacteria grow and metabolize faster.At 20 o C, the degradation of TPH increased rapidly after 10 days of testing, which indicates that the bacteria slowly adapted to the low temperature environment.The total degradation percentage of TPH rate was 60% at 20 o C, which was 20% lower than the degradation percentage of the experimental group tested at a higher temperature (30 o C).

Fig. 3 .
Fig. 3.The degradation rate of TPH by seven strains

Fig. 4 .
Fig. 4. Average degradation rate of cell by seven strains

Fig. 5 .
Fig. 5.The effect of inoculum volume and concentration of TPH in contaminated soil on biodegradation efficiency Fig.10indicates that SY 22 and SY 23 strains could degrade oil at a pH=9.0 with degradation efficiencies of 80% and 69.4%, respectively.Meanwhile, strains SY 24 and SY 42 had the ability of degrading oil at a pH value of 7.0 with degradation efficiencies of 73.1% and 74.9%, respectively.

Fig. 12 .
Fig. 12. TIC of remaining TPH concentration in soil on different treatment condition 230

235 5 . 4 and discussions 5 . 4 . 1 Figure 15 and
Figure15 and Figure16show the residual TPH concentration and the TPH degradation rate in soil as a function of bacteria dosage and time.The initial TPH concentration in soil was 4.3 g•kg -1 .The dosage of bioaugmentation products was 0.01, 0.2, 0.4, and 0.6mg•kg -1 respectively.Figure16indicates that the TPH degradation rate after 8 days of biodegradation for the corresponding bacteria dosage conditions were 2%, 10%, 25%, and 40% respectively.While, the degradation rate of the blank sample without bacteria (CK) was only 3%.The TPH degradation efficiency during 48 days of testing was 47%, 68%, 79%, and 87%; while the degradation efficiency in the blank sample (CK) did not achieve even 20%.

Fig. 19 .
Fig. 19.TIC TPH concentration in the soil at different injection schemes of the bioaugmentation products

Fig. 20 .
Fig. 20.TPH concentration in the soil as a function of temperature and degradation time

Table 1 .
. Characteristics of Oil-Contaminated Soil Samples The culture medium per unit used in this work was: 2 g of NH 4 NO 3 , 1.5 g of K 2 HPO 4 , 3 g of KH 2 PO 4 , 0.1 g of MgSO 4 •7 H 2 O, 0.01 g of anhydrous CaCl 2 , 0.01 g of Na 2 EDTA•2H 2 O, 1 g of crude oil, 1000 mL of distilled water, with a pH ranging from 7.2 to 7.4.

Table 2 .
Growth And Identification of the Isolated Strains Cultivated in Hydrocarbon Medium After 7 Days of Cultivation These strains of petroleum-degrading active bacteria were all gram-negative bacteria.The strains SY 21 , SY 22 , SY 23 , SY 24 , SY 42 , SY 43 , and SY 44 were identified as acinetobacter, neisseria, plesiomonas, xanthomonas, zoogloea, flavobacterium, and pseudomonas, respectively.Previous research has shown that gram-negative bacterium dominate in microbes that can degrade petroleum hydrocarbon

Table 3 .
22 , SY 23 , SY 24 , SY 42 , and SY 43 are capable of degrading more than one hydrocarbon, which makes them potential candidate strains for the bioremediation of petroleum contaminated soil.SY 21 SY 22 SY 23 SY 24 SY 42 SY 43 SY 44 SY 21 SY 22 SY 23 SY 24 SY 42 SY 43 SY 44 C Growth Tendency And Degradation Efficiency of the Seven Isolated Strains in Different Hydrocarbon Medium

Table 4 .
Effect of Petroleum Hydrocarbon Concentration on the Strains Hydrocarbon Degradation Efficiency mg/L.These results indicate that excessive concentration of petroleum hydrocarbon restricted the growth of the strains and consequently reduced the hydrocarbon degradation efficiency.The SY 23 strain showed the highest TPH degradation efficiency at all TPH concentrations, which indicates its endurance to the TPH toxicity.

Table 5 .
Effect of Nitrogen Sources on the Petroleum Hydrocarbon Degradation Efficiency

Table 6 .
Effect of Carbon Sources on the Strains Petroleum Hydrocarbon Degradation Efficiency

Table 7 .
Effect of Metal Ions on the Strains Degradation Efficiency Seven strains were isolated from petroleum contaminated soil.The degradation efficiency of oil after seven days of cultivation ranged from 43.8% to 58.9%, which indicates high strains activity.These strains show a logarithm growth trend after 12 to 13 hours of inoculation with an average growth rate of the respective colonies between 2.49 to 2.4 mm/d.2. The strains SY 21 , SY 22 , SY 23 , SY 24 , SY 42 , SY 43, and SY 44 were categorized as acinetobacter, neisseria, plesiomonas, xanthomonas, zoogloea, flavobacterium and pseudomonas respectively.3.These strains are capable of using normal octane, paraffin wax, benzene, methylbenzene, phenol, and naphthalene as the solo carbon source.Five of these strains: SY 22 , SY 23 , SY 24 , SY 42 and SY 43 show the ability of degrading more than one hydrocarbon, which make them potential candidates for the bioremediation of petroleum contaminated soil.4. A pH value of 7.0 was optimum for the growth of strains SY 21 and SY 42 while a pH value of 9.0 was optimum for the development of strains SY 22 and SY 23 .5. The strains show an optimum degradation of petroleum hydrocarbon when NH 4 NO 3

Table 9 .
GC-MS Analysis of Petroleum Hydrocarbon after Adding Bulking Agents

Table 10 .
These data indicates that the removal rate increases with tillage times.

Table 10 .
Half-life of the Petroleum Contaminant in Soil at Different Tillage Times www.intechopen.com

Table 11 .
Experimental Observations www.intechopen.comBioremediation of Crude Oil Contaminated Soil by Petroleum-Degrading Active Bacteria

Table 12 .
Half-life of the Petroleum Contaminants in Soil at Different Dosage Conditions Table 13 presents the (TPH) degradation rate as a function of bacteria dosage for a period of 48 days.Specific charge (m/z) measurement was used to determine chemical structure.The specific charge (m/z) for CH 3 CH 2 CH 2 CH 2 is 57, for 3 CH CH CH 2 is 55.So that, Table

Table 13 .
Peak Area and Removal Rate of Alkane & Alkene in Soil at Different Dosage of Bacteria