Polymers, high molecular weight compounds, have most essential position in the materials field today even though have been introduction in meaning full logic more recently. In performance, characteristics, and application predictions, polymers offer novelty and usefulness not to be found in other kinds of materials. The rapidity of the all-round developments in polymer science and technology and the unique pace of application development and developments in the design of products and parts and components of polymer processing equipment necessitate fresh efforts in organizing old and established thoughts, ideas, concepts, and practices and updating them in the light of the latest unfolding polymer. Polymer constitutes a diverse range of light- and energy-efficient materials discovered and developed in a large measure out of the sheer necessity of meeting the growing needs and demands of our higher-profile society. The present level of sophistication, growth, and advancements of our expanding society has been made possible in a large measure through continued imaginative and creative efforts of scientists, engineers, and technologists in the polymer field.
In recent years there is a considerable demand for specialty supplies, and there is an increasing affinity to design “intelligent polymers,” i.e., specialty polymers, which extend the scope of polymeric materials. Natural polymers have been used throughout the ages. From the beginning man has depended upon animal and vegetable matter for nutrition, shelter, warmth, and other requirements and desires. It is utilized in the field of pharmacology, diagnosis, and artificial respiration and in creation of articles of patient care. Commercially accessible synthetic polymeric materials are long lasting and have noble mechanical properties such as tensile strength and abrasion resistance, but because of the lack of functional groups in them, they resist dyeing and resist chemical reactions. The properties can be further improved by introducing various functional groups into their molecules. This ranges the scope of polymeric materials. Efforts have been made to use readily available natural polymers such as cellulose, proteins, gums and rubber, etc., for making polymers better properties. Copolymerization is an important method for the modification of polymers.
Copolymerization is defined as “a process in which two or more structurally different monomers are incorporated into the same polymeric chain.” The properties of polymer produced by copolymerization can be varied over a wide range by adjusting the monomer ratio. Copolymerization involves a chemical reaction between two or more different monomers, which results the formation of following different types of copolymers.
1. Random copolymer
The distribution of the monomer units in the polymer chain does not follow any definite sequence:
This type of copolymer is produced in bulk, aqueous, suspension, or emulsion using free radical initiators of peroxide type or redox systems.
2. Alternate copolymer
In these copolymers the monomers are arranged in an alternate sequence. These monomer units react with a high degree of order forming a polymer chain having a degree of alteration as
Special methods are used for manufacturing alternating copolymers. The reactivity of polar monomers can be enhanced by complexing them with metal halide or organo-aluminum halide. These complexed monomers participate in one electron transfer reaction with either an uncomplexed monomer or another electron donor monomer.
3. Block copolymer
These copolymers are built up of chemically different terminally connected segments. Block copolymers are generally prepared by sequential anionic addition or ring opening or step growth polymerization:
4. Graft copolymer
Graft copolymers are branched molecules where the main chain is made entirely of one repeat unit, while branch chains are made of yet additional repeat unit. The structure of such copolymer may be represented as
Grafting by most of the known methods includes the attachment of only a small number of side chains on the backbone polymer. During grafting there is little agitation, and, therefore, the bulk properties of polymer undergo little changes. The side chains disturb the uniformity of lattice, and the crystalline content of such polymer becomes smaller with an increasing degree of branching. However, the most attractive method of modifying the nature of polymer is graft copolymerization.
Graft copolymers are generally prepared by free radical and anionic or cationic initiation process creating the active centers at polymer backbone. The mode of synthesis was first recommended by Flory  in 1937. The concept of graft copolymerization was first familiarized by Bandel and Alfrey . Thus, graft copolymer is a macromolecule consisting of a block of constitutional units of backbone and blocks of unit grafts attacked to the backbone.
Random and alternating copolymers, ready by polymerizing two kinds of monomers, possess better properties than constituent homopolymer; on the other hand, graft and block copolymers exhibit many properties that are characteristics of each constituent homopolymer. Conditions are usually so chosen as to retain the desirable properties and to eliminate the less desirable properties of the individual block or graft components. By grafting, some new properties allied with the side chains are added without drastically changing the basic properties of the substrate polymer.
The properties such as thermal stability and improvement in metal ion uptake, viscosity, ion exchange capacity, resistance to biodegradation, flocculation, etc. have been achieved on natural and synthetic polymers over graft copolymerization [1, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14]. These modified polymers called as graft copolymers have been found to be useful in oil recovery [15, 16, 17].
Graft copolymer of vinyl monomers bearing (+ve) charge or episulfide groups onto certain fibers has newly been reported to possess antibacterial activity. Synthetic MMA-grafted polysaccharides have been used as a hydrophilic matrix for controlled release forms .
5. Synthesis of graft copolymers
Most of the method of producing graft copolymers involves the use of radical polymerization although ionic graft copolymerizations are also possible. Graft copolymerization can be carried out either in homogeneous or heterogeneous systems depending whether the polymer being grafted and monomer is soluble or insoluble in the solvent being used. Usually grafting can occur by either the “grafting from” or “grafting onto” method as illustrated by the following:
5.1 Grafting from
An active site generated along a polymer backbone starts to propagate monomer and thus produces branches.
5.2 Grafting onto
A growing polymer chain P2 attacks another polymer P1.
The preparation of a graft (−ve) copolymer in most cases starts from a homopolymer (A) which is suitably activated, and then the growth of the graft of monomer (B) is initiated. The model must fulfill the following requirements:
The copolymer is of poly (A-g-B) type.
The probability that a graft will grow on a given unit of the backbone is not contingent on the number or size of the other grafts in the molecule or on the size of the backbone to which it is attached.
The efficiency of grafting is dependent upon several competing reactions:
Competition between the various species present in the reaction mixture such as monomer, solvent, and backbone for the growing polymer radical, which means that there is competition between chain growth and various chain transfer steps.
Competition for the initiator radical between monomer and backbone.
Competition among the terminating process such as disproportionation after the polymer radical has formed.
Competition among the terminating process in growing grafted species.
If the termination occurs through recombination of rising polymeric chains, it should lower the grafting efficiency. But even though the efficiency of this process is low, it has received considerable use because the reaction is easily carried out. The other reaction parameters, such as concentration of the initiator monomer, temperature, and the time of reaction, affect the grafting efficiency. The nature of the initiating radicals appears to bear a strong influence on the efficiency of grafting.
The graft copolymer is detached from the homopolymer by the solvent extraction method. Often graft copolymer prepared from water-soluble backbone polymers and water-soluble vinyl monomers is also water-soluble. In such cases graft copolymer is precipitated by using appropriate precipitating agent, and homopolymer is also separated. This method of parting has been successfully applied in many systems [19, 20, 21, 22, 23, 24, 25, 26, 27]. However, if it is not possible to separate the homopolymer from graft copolymer, such products are referred to as composites. Evidence for grafting in such case has been gotten from turbidimetric studies [27, 28].
5.3 Method of grafting
Combination and characterization of graft copolymers have received considerable interest in recent years due to its industrial importance. The chemistry of graft copolymerization essentially involves the generation of active site on the backbone polymer where appropriate monomer can be grafted. Different methods of activation include:
5.3.1 Physical activation
Physical activation contains the application of stress to polymeric backbone swelling it with suitable solvents [7, 29]. Application of stress to polymeric backbone causes segmental motions and molecular flow, which may lead to bond scission and consequent formation of free radicals. Freezing and thawing of the polymer-monomer mixture also make active sites. Free radicals may also be generated by mastication and milling of the backbone polymer. Production of a polymer with pendant basic moieties was performed by grafting dimethylamino-ethyl-methacrylate to linear low-density polyethylene (LDPE) in the melt in a batch-type internal mixer.
5.3.2 Chemical activation
This method of activation includes two different mechanisms:
Free radical mechanism
184.108.40.206 Free radical mechanism
220.127.116.11.1 Radical initiators
In the existence of radical initiators such as benzoyl peroxide (BPO), azobisisobutyronitrile (AIBN), persulfates (), etc., grafting of vinyl monomers onto polymeric backbones involves generation of free radical sites by hydrogen abstraction and chain transfer processes as described below:
The extent of grafting is dependent on various reaction parameters, such as concentrations of initiator and monomer, reaction time, temperature, etc. The nature of initiator and monomer influences the reactivity of initiator and monomer toward grafting. Misra et al. have observed that during grafting of vinyl monomer onto starch, wool, or rubber, conservative free radical initiators show different reactivity toward grafting.
Although this process is not very efficient, it has received considerable importance because it is industrially important. The major drawback of this process is that it produces considerable amount of homopolymer. Therefore, various radical initiators are employed to graft different vinyl monomers on natural and synthetic polymeric backbones so as to minimize the production of homopolymer.
18.104.22.168.2 Redox systems
In redox systems the free radicals, which initiate polymerization, are generated as transient intermediates in the course of redox reaction. Essentially this involves an electron transfer process followed by scission to give free radicals. A wide variety of redox reactions, linking both organic and inorganic components, are used for this purpose. These reactions take place in aqueous media and occur rather rapidly even at relatively low temperatures. The general mechanism of grafting involves an abstraction of the hydrogen atom from the backbone of the polymeric material by the transient radical formed during the redox reaction, thus generating macro radicals onto which the monomer molecules are added to produce graft copolymer.
Flory PJ. The mechanism of vinyl polymerizations. Journal of the American Chemical Society. 1937; 59:241
Alfray, Bandel D. Presented at 118th American Chemical Society Meeting, Chicago, Sept. 4 (1950) through H. Mark Res. Chem. Progr. 1951; 12(3):139
Hummel DO. Fluorinated polymers with functional groups. Journal of Polymer Science, Polymer Symposia. 1980; 67:169
Sperling LH, editor. Recent Advances in Polymer Blends, Graft and Blocks. New York: Plenum Press; 1974
David NS. Graft copolymerization of lignocellulosic fibres. ACS Symposium Series. Vol. 187. 1982
Ranby B, Zuchowska D. Mechanical properties of multicomponent polymeripreparation and characterization of interpenetrating network beads of poly(vinyl alcohol)‐grafted‐poly(acrylamide) with sodium alginate and their controlled release characteristics for cypermethrin pesticide. Polymer Journal. 1987; 19(15):623
Sedlaceak B, Overberger CG, Mark HF, editors. Medical polymers chemical problems. In: Proceedings of 17th Prague IUPAC Microsymposium on Macromolecules; Prague, Czechoslovakia; 1977. Journal of Polymer Science: Polymer Symposia. 1979; 66
Sakamoto M, Hasuike H, Itoh M, Ishizuka Y, Yoshida K, Wtamoto H, et al. Modification of polymers by graft copolymerization. Cellulosics: Chemical, Biochemical and Material Aspects. 1993:391-396
Iyer V, Varadaragan PV, Sawakhande KH, Nachave ND. Water‐superabsorbent polymers through gamma radiation‐induced graft‐copolymerization of acrylonitrile on guar gum. Journal of Applied Polymer Science. 1990; 39(11–12):2259
Miyata N, Sakata I. Experimental and theoretical considerations of electrolyte conductivity in glucose alkaline fuel cell. Japanese Kokai Tokkyo Koho. 1988; 6(397):612
Takagi T, Nitta A, Ito H, Nagai K. Inhibitory effects of purified green tea epicatechins on contraction and proliferation of arterial smooth muscle cells. Japanese Kokai Tokkyo Koho. 1988; 1:89, 252, 610
Saito T, Sesaki M, Mafande Y. Antifungal activity of polymer-based copper nanocomposite coatings. Japanese Kokai Tokkyo Koho. 1986; 61:86, 101, 506
Ghosh P, Biswas S, Datta C. Concise polymeric materials encyclopedia. Journal of Materials Science. 1989; 24(1):205
Tripathi M, Karmakar NC, Singh RP. Modification of polymers by graft copolymerization. International Journal of Polymeric Materials. 2000; 46(2):81-93
Yazdani-Pedram M, Retwart. Understanding biomaterial-tissue interface quality: Combined in vitro evaluation. Soc. Symp. Proc. (Biomedical material-drug delivery, implants and tissue engineering). Journal of Materials Research. 1999; 550:29-34
Leansheng Z. European Patent Application. 1990; 356:241
Meister JJ. U.S. 454, 889, 902. 1989
Zhang L-M, Tan Y-B, Li Z-M. Heterogeneous emulsion graft polymerization of glycidyl methacrylate on a wood matrix. Applied Polymer Science. 2001; 77(1):195-201
Castellano I, Goni I, Ferrero MC, Munoz A, Manez-Castellanos R, Gurruchaga M, et al. Selective separation of some heavy metals by poly (vinyl alcohol)-grafted membranes. The Indiana Pharmacist. 1999; 25(12):1249-1257
Behari K, Pandey PK, Kumar R, Taunk K. Graft copolymerization of acrylamide onto xanthan gum. Carbohydrate Polymers. 2001; 46(2):185-189
Behari K, Kumar R. Graft copolymerization of methacrylamide onto guar gum using potassium chromate/malonic acid redox pair. Polymeric Materials: Science and Engineering Division (American Chemical Society). 2001; 85:361
Behari K, Taunk K. Graft copolymerization of acrylic acid onto Guar Gum. Journal of Applied Polymer Science. 2002; 84(13):2380-2385
Behari K, Kumar R, Srivastava A. Studies on aqueous polymerization of 2 acrylamido 2 methyl 1 propane sulphonic acid initiated by peroxydiphosphate/Ag(I)—A kinetic study. Polymer Prepints (ACS). 2003; 44(1):882
Behari K, Kumar R. Polymerization of N,N'methylenebis acrylamide by potassium peroxydiphosphate in presence of Mn II and Ag I. Polymer Materials Science & Engineering. 2003; 88:459
Behari K, Pandey PK, Taunk K, Banerjee J. Synthesis and characterization of xanthan gum‐g‐N‐vinyl formamide with a potassium monopersulfate/Ag(I) system. Journal of Applied Polymer Science. 2003; 89(5):1341
Behari K, Kumar R. Synthesis of carboxymethyl cellulose g acrylamide using ferrous sulphate potassium bromate redox pair. Polymer Preprints (ACS). 2003; 44(1):1251
Kaur I, Misra BN, Barsala R, Singh K. The estimation of mechanical properties of polymers from molecular structure. Journal of Applied Polymer Science. 1993; 47:1165
Kaur I, Misra BN, Chauhan S, Chauhan MS, Gupta A. Phenolphthalein-based cardo poly(arylene ether sulfone): Preparation and application to separation membranes. Journal of Applied Polymer Science. 1996; 59:389
Kaur I, Maheshwari S, Gupta A, Misra BN. Viscometric and conductometric studies of poly(vinyl alcohol)‐g‐polyacrylamide composites. 1941