Probability of detection (PD) without cluster reporting time under SNR versus number of clusters.
Consequently, the research and development for the 5G systems have already been started. This chapter presents an overview of potential system network architecture and highlights a superallocation technique that could be employed in the 5G cognitive radio network (CRN). A superallocation scheme is proposed to enhance the sensing detection performance by rescheduling the sensing and reporting time slots in the 5G cognitive radio network with a cluster‐based cooperative spectrum sensing (CCSS). In the 4G CCSS scheme, first, all secondary users (SUs) detect the primary user (PU) signal during a rigid sensing time slot to check the availability of the spectrum band. Second, during the SU reporting time slot, the sensing results from the SUs are reported to the corresponding cluster heads (CHs). Finally, during CH reporting time slots, the CHs forward their hard decision to a fusion center (FC) through the common control channels for the global decision. However, the reporting time slots for the SUs and CHs do not contribute to the detection performance. In this chapter, a superallocation scheme that merges the reporting time slots of SUs and CHs by rescheduling the reporting time slots as a nonfixed sensing time slot for SUs to detect the PU signal promptly and more accurately is proposed. In this regard, SUs in each cluster can obtain a nonfixed sensing time slot depending on their reporting time slot order. The effectiveness of the proposed chapter that can achieve better detection performance under –28 to –10 dB environments and thus reduce reporting overhead is shown through simulations.
- software‐defined network
- cognitive radio
- superallocation technique
- cluster head
- fusion center
Around 2020, the promising 5G technology in cognitive radio networks is expected to be developed 5G networks that will have to support advanced services and multimedia applications with a wide variety of requirements, including higher peak and user data rates, reduced latency, enhanced indoor and outdoor coverage, improved energy efficiency, capacity and throughput, network densification, autonomous applications and network management, and Internet of things [1, 2].
Network densification of existing mobile cellular networks (e.g., peer‐to‐peer [P2P], machine‐to‐machine [M2M], device‐to‐device [D2D], and heterogeneous networks);
Full‐duplex (FD) communication (e.g., simultaneous transmission and reception);
Improvement of capacity and throughput (e.g., massive multiple‐input multiple‐output [massive MIMO]);
Improvement of energy efficiency by wireless charging and energy harvesting;
Advanced services and applications by a cloud‐based radio access network (C‐RAN) (e.g., smart city and service‐oriented communication);
Multiple network operators to share common resources by cooperation and network virtualization (e.g., network infrastructure, backhaul, licensed spectrum, core and radio access network, energy/power, etc.).
In this chapter, the main objectives of the beyond 2020 5G cognitive radio network by providing the technical support that needed to address the very challenging requirements foreseen for this time frame are proposed. A 5G system (i) has to be significantly more efficient in terms of energy, cost, and resource utilization (e.g., licensed spectrum utilization) than today's system (e.g., 4G); (ii) has to be significantly more versatile to support a significant diversity of requirements; and (iii) should provide better scalability in terms of the number of connected devices, densely deployed access points, spectrum usage, energy, and cost. In CRN, both higher data volume and higher data rates are required to access more spectrum band. As mentioned before, in 4G, it is clearly expected that more spectrum will be released for licensed wireless mobile communications. This new spectrum lies in the frequency range between 300 MHz and 6 GHz. However, for the future 5G system, these new spectrum opportunities will not be sufficient. Moreover, wireless local area networks operating in the unlicensed bands, such as the ISM and U‐NII bands at 2.4 and 5 GHz, as well as the 60 GHz band, can be more tightly integrated. The present chapter discusses the superallocation and cluster‐based cooperative spectrum sensing in the 5G CRN (e.g., highlights the number (i)) to provide more efficient spectrum utilization.
Cognitive radio (CR) is a new promising technology in the wireless communication era that has changed the policy of spectrum allocation from a static to a more flexible paradigm . Recently, CRs that enable opportunistic access to underutilized licensed bands have been proposed as a promising technology for the improvement of spectrum operations. In an overlay cognitive radio network, an overlay waveform is used to exploit idle spectra and transmit information data within these unused regions. On the other hand, in an underlay cognitive radio network an underlay waveform with low transmit power is used to transmit data without harmful effects on the primary network . In this chapter, we focus on overlay networks where secondary users find the idle channel with spectrum sensing. A precondition of secondary access is that there shall be no interference with the primary system . This means spectrum sensing plays a vital role in the 5G CRN.
There are a number of spectrum sensing techniques, including matched filter detection, cyclostationary detection, and energy detection [6–8]. Matched filter detection is known as the optimum method for detection of the primary users when the transmitted signal is known. The main advantage of matched filtering is that it takes a short time to achieve spectrum sensing below a certain value for the probability of false alarm or the probability of detection compared to the other methods. However, it requires complete knowledge of the primary user's signaling features, such as bandwidth, operating frequency, modulation type and order, pulse shaping, and packet format. Cyclostationary detection is especially appealing because it is capable of differentiating the primary signal from the interference and noise. Due to noise rejection property, it works even in a very low signal‐to‐noise ratio (SNR) region, where the traditional signal detection method such as the energy detection is used. It offers good performance but requires knowledge of the PU cyclic frequencies and also requires a long time to complete sensing. On the other hand, the energy detection senses spectrum holes by determining whether the primary signal is absent or present in a given frequency slot. It operates without the knowledge of the primary signal parameters. Its key parameters, including detection threshold, number of samples, and estimated noise power, determine the detection performance. Also, it is an attractive and suitable method due to its easy implementation and low computation complexity. However, it is vulnerable to the uncertainty of noise power and cannot distinguish between noise and signal. Conversely, its major limitation is that the received signal strength can be dangerously weakened at a particular geographic location due to multipath fading and the shadow effect .
In order to improve the reliability of spectrum sensing, cooperative spectrum sensing was proposed [10–13]. Each SU performs local spectrum sensing independently and then forward the sensing results to the fusion center (FC) through the noise‐free reporting channels between the SUs and the FC. In Zarrin and Lim , basic methods including AND, OR, and k‐out‐of‐N logic are used to take hard decisions for a final decision at the FC. However, the reporting channels are always subject to fading effects in real environments . When reporting channels become very noisy, cooperative sensing offers no advantages [15–16]. To overcome this problem, Sun et al.  and Xia et al.  proposed a cluster‐based cooperative sensing scheme by dividing all the SUs into a number of clusters and selecting the most favorable SU in each cluster as a CH to report the sensing results, which can dramatically reduce the performance deterioration caused by fading of the wireless channels. In these schemes, the SU selected as the CH has to fuse sensing data from all cluster members (the SUs in this cluster). However, in these schemes, each SU's reporting time slot and the CH reporting time slot offer no contribution to spectrum sensing, while SU sensing and reporting times and CH reporting time are in different time slots.
Jin et al.  proposed a superposition‐based cooperative spectrum‐sensing scheme that increases the sensing duration by super positing the SUs’ reporting duration into the sensing duration. However, this scheme adopts various individual reporting durations. In this case, synchronization problems occur at the FC. Moreover, the data processing burden at the FC increases for a large CR network.
In this chapter, we propose a superallocation and cluster‐based cooperative spectrum sensing 5G scheme to provide more efficient spectrum sensing. In this scheme, each SU achieves a nonfixed and longer sensing time for sensing the PU signal bandwidth because both the SUs and the CHs are superallocated to different reporting time slots. On the other hand, both the SU and the CH reporting time slots are of fixed length because the synchronization problem for the FC is relieved. In addition, this proposed scheme decreases the data processing burden of the FC while all the SUs in the CRN are divided into fewer clusters such that each SU reports its local decision to the corresponding CH, which then reports to the FC. Simulation results show that the proposed 5G scheme can improve sensing performance in a low signal‐to‐noise ratio environment (i.e., –28 dB) and also greatly reduces reporting overhead in comparison with cluster‐based cooperative spectrum sensing in 4G CRNs.
The remainder of this chapter is organized as follows. Section 2 describes the system model. Section 3 offers an overview of energy detection. Section 4 describes the cluster‐based cooperative spectrum sensing in the 4G CRN. The proposed superallocation and cluster‐based cooperative spectrum sensing in the 5G CRN is presented in Section 5 that addresses the spectrum utilization goal of this chapter for the 5G CRN. Some simulations and comparisons are presented in Section 6. We finally present the main conclusion of this chapter in Section 7.
2. Cognitive radio network system model
In CRN, the detection performance of the PU signal might be degraded when the sensing decisions are forwarded to an FC through fading channels. Figure 1 shows the CRN deployment where SUs are grouped into a cluster governed by a CH based on low‐energy adaptive clustering hierarchy‐centralized (LEACH‐C) protocol  and the CHs of the clusters report their decisions to an FC through a common control channel. Here, HDF will be applied to obtain a final decision on the presence of the PU activities. The process of the LEACH‐C protocol is made up of several rounds, and each round consists of two phases: a setup phase when the CHs and clusters are organized and a steady‐state phase when the cluster members begin to send their measurements to CH and CHs send their decision to the FC. In the setup phase, each SU sends information about its current location and SNR of reporting channel to the FC. Based on this information, the FC determines CHs among all CRUs, while the remaining CRUs will act as cluster members. After the CHs are determined, the FC broadcasts a message that contains not only the CH ID for each SU but also the information of time synchronization. If an SU's CH ID matches its own ID, the SU is a CH; otherwise, the SU is a cluster member and goes to sleep. In the steady‐state phase, the SUs start to forward the measurement of the received PU's signal to the CH, and then the CH collects the measurements from the cluster members and makes the cluster decision about the presence of the PU and sends it to the FC during their allocated reporting time slots. Afterward, the FC combines the received clustering decision to make the final decision, then broadcasts it back to all CHs and the CHs send it to their cluster members.
Spectrum sensing can be formulated as a binary hypothesis‐testing problem as follows:
Each SU implements a spectrum sensing process that is called local spectrum sensing to detect the PU's signal. According to the status of the PU, the received signal of an SU can be formulated as follows:
where represents the received signal at the
In addition, we make the following assumptions :
is a binary phase shift keying (BPSK) modulated signal.
and are mutually independent random variables.
The SU has complete knowledge of noise and signal power.
Cluster‐based cooperative spectrum sensing in a 5G CRN is shown in Figure 1 , which contains N SUs,
For sensing duration, first, each SU calculates the energy of its received signal in the frequency band of interest. Local decisions are then transmitted to the corresponding CH through a control channel, which will combine local decisions to make a cluster decision. Second, all cluster decisions will be forwarded to the FC through a control channel. At the FC, all cluster decisions from the CHs will be combined to make a global decision about the presence or the absence of the PU signal.
3. Overview of energy detection
The energy detection method has been demonstrated to be simple, quick, and able to detect primary signals, even if prior knowledge of the signal is unknown [22–25]. A block diagram of the energy detection method in the time domain is shown in Figure 2 . To measure the energy of the signal in the frequency band of interest, a band‐pass filter is first applied to the received signal, which is then converted into discrete samples with an analog‐to‐digital (A/D) converter.
An estimation of the received signal power is given by each SU with the following equation:
where is the
where denotes a Gaussian distribution with mean of and variance of , and represent the mean and variance, respectively, for hypothesis , and and represent the mean and variance for hypothesis .
where that is the SNR of the primary signal at the
From Boyed and Vandenberghe , variance is
For a complex
For the CSCG noise signal , is given as
Substituting the values and into Eq. (7), we obtain
For hypothesis , substituting the value into Eq. (6), mean is expressed as
Again, substituting the value into Eq. (7), variance is expressed as
Then, we can have distributions of a decision statistic under null and alternative hypotheses as in Eq. (5).
By the definition of a false alarm probability in a hypothesis testing with a decision statistic of depending on , and a decision threshold of , the probability of false alarm for the
where is the Gaussian tail function given by . Form Lemma 1, the probability of false alarm under a CSCG noise is given by
By the definition of a probability of detection in hypothesis testing and Lemma 1, the detection probability for the BPSK‐modulated primary signal under a CSCG noise for the
The last equality is obtained by using Eq. (5).
4. Cluster‐based cooperative spectrum sensing in the 4G CRN
A general frame structure for the cluster‐based cooperative spectrum sensing in the 4G CRN is shown in Figure 3 . With this frame structure, all local decisions are forwarded to the CHs in the scheduled SU reporting time slots and are then forwarded to the FC in the scheduled CH reporting time slots.
to sense the PU's signal with false alarm and detection probabilities of and , respectively. Here, the superscript “con” means the conventional or 4G CRN.
From Eq. (15), the probability of false alarm can be obtained by
Defining the sensing time with the last equation in Eq. (20), i.e., , we can meet the requirement on false alarm and detection probabilities.
Because all SUs in
5. Proposed superallocation and cluster‐based cooperative spectrum sensing in the 5G CRN
In the 4G CRN approach, sensing time slots, reporting time slots of SUs, and reporting time slots of CHs are strictly divided as shown in Figure 3 . Due to this rigid structure in the 4G CRN approach, the reporting time slots of other SUs and CHs are not used for spectrum sensing. However, these reporting time slots can be used in sensing the spectrum by other SUs by scheduling sensing and reporting time slots effectively. To this end, a superallocation and cluster‐based cooperative spectrum sensing in the 5G CRN is proposed by increasing the sensing time slot. In the proposed 5G CRN, each SU can obtain longer sensing time slot because the other SU reporting times and the CH reporting times are merged to the SU sensing time. Therefore, the sensing time slots for SUs in the proposed 5G CRN can be longer than those in the 4G CRN.
Figure 4 shows the proposed scheduling method of sensing and reporting time slots in the superallocation for cluster‐based cooperative spectrum sensing in the 5G CRN. In the figure, SU
In this proposed scheme, the sensing time slot for the first SU in the first cluster, i.e., SU11, is equal to the sensing time slot in the 4G CRN, i.e., . Except for SU11, other SUs can obtain longer sensing time slots by scheduling SU reporting slots followed by the reporting slot for the CH of that cluster. With such a scheduling method, SUs can sense the spectrum during the reporting time slots of other SUs and CHs. For example, the sensing time slot of SU12, is equal to the total duration of sensing time slot and the reporting time slot of the SU11, i.e., . Similarly, becomes the sum of the sensing duration of SU12 and the reporting duration of SU12, i.e., . Obviously, the relationship of the sensing time slot of the SU1 (
When for , the sensing time slot of the
Therefore, in the first cluster is greater than or equal to .
For SU in the other clusters, the reporting time slots of SUs in the previous clusters and that of the previous CH can be used for a sensing time slot of SUs in the current cluster. Thus, is given by
Here, is the duration of the reporting time slot of a CH. Therefore, we can obtain longer sensing time as the index of CH increases.
5.1. Local sensing
As shown in Eq. (16), the detection probability is a function of parameters , , and . For fixed and , is a function of , which can be represented as .
Substituting the values of and into Eq. (16), we have
When the sensing time becomes longer, then obviously the detection probability increases. Hence, we show that
Because for . When then we obtain .
If SU is not included in the first cluster, denotes the probability of detection for the proposed scheme. In this case, the sensing time slot includes the CH reporting time slots. Substituting the value of into Eq. (16), we obtain
Each SU makes a local hard decision as follows.
5.2. Cluster decision
where is the threshold for the cluster decision.
5.3. Global decision
At the FC, all cluster decisions received will be combined to make a global decision about the presence or the absence of the PU signal by using a
where is the threshold for the global decision.
6. Simulation and result analysis
To evaluate the performance of the proposed cluster‐based cooperative spectrum sensing in the 5G CRN, Monte Carlo simulations were carried out under following conditions:
The number of SUs is 12.
The number of clusters is 3.
The number of SUs in each cluster is 4.
The durations of sensing, SU reporting, and CH reporting time slots are 1 ms.
Average SNR of each SU in a cluster is –17 dB.
The PU signal is a BPSK signal.
The noise in SUs is CSCG.
The number of samples is 300.
First, the sensing performance of the proposed 5G and 4G cluster‐based schemes, in terms of receiver operating characteristic (ROC), was evaluated under a CSCG channel. In this simulation, each SU conducts local sensing using equal gain combining (EGC).
Figures 5 and 6 show ROC curves for the proposed 5G cluster‐based schemes without and with cluster reporting time (RT), respectively. The proposed 5G scheme outperforms in the detection of the PU compared with the 4G scheme because the proposed superallocation technique can have longer sensing time than the 4G one. Test statistics (Eq. (25)) was considered for the proposed 5G scheme without reporting time for the cluster decision. In addition, test statistics (Eq. (27)) was considered for the proposed 5G scheme with reporting time for the cluster decision. When the index of the cluster increases from one to three, the detection probability increases ( Figures 7 and 8 ).
From the detection efficiency of cooperative spectrum sensing, the probability of detection is 0.8 and the probability of false alarm is 0.2. However, in the worst environment, we need the probability of detection to be more than 0.9 and the probability of false alarm to be less than 0.1. In the 4G scheme, we can achieve these sensing performances with a longer sensing time slot but the throughput of the 4G cognitive radio network decreases. In the proposed 5G CRN, we can easily achieve more than 0.9 and less than 0.1 for the probabilities of detection and false alarm, respectively, because SU reporting time and CH reporting time merge to sense the PU signal without decreasing system throughput.
Second, the simulation was carried out under conditions whereby the SNRs of the PU's signal at the nodes are from –28 to –10 dB. The ROC curves of the proposed 5G scheme without cluster reporting time and the 4G CRN are illustrated in Figure 9 . For our proposed 5G CRN scheme, it can be seen that the probability of detection increases as sensing time, , increases.
The ROC curves of the proposed 5G CRN scheme with cluster reporting time versus the 4G scheme are shown in Figure 10 . Figures 9 and 10 show that the probability of detection in the proposed 5G scheme with cluster reporting time is better than the proposed 5G scheme without cluster reporting time.
In Tables 1 and 2 , the exact values of detection probabilities in the proposed 5G and 4G CRNs are shown. The gain of sensing performance can be verified with the results. For example, the proposed method with a cluster reporting time can detect the spectrum with nearly 100% detection probability whereas the 4G one detects the PU's signal with 78% of detection probability in –10 dB SNR.
|Proposed 5G Scheme||Cluster 1||0.5073||0.5122||0.5209||0.5421||0.5473||0.5775||0.6290||0.6944||0.7810||0.8776|
|Proposed 5G scheme||Cluster 1||0.5112||0.5170||0.5207||0.5316||0.5517||0.5743||0.6342||0.6993||0.7883||0.8835|
In this chapter, we propose the superallocation and cluster‐based cooperative spectrum sensing in a 5G CRN. The proposed 5G scheme can achieve better sensing performance in comparison with the cluster‐based cooperative spectrum sensing 4G cognitive radio network. By rescheduling the reporting time slots of SUs and CHs, longer sensing durations are guaranteed for SUs depending on the order of reporting times of SU and CH. With simulations, the gain of performance is verified ( Tables 1 and 2 ).