Open access peer-reviewed chapter

Design and Implementation of UWB CPW-Fed Planar Monopole Antenna with Dual Band Rejection Characteristics

By Woo Chan Kim and Woon Geun Yang

Submitted: October 20th 2010Reviewed: March 20th 2011Published: August 9th 2011

DOI: 10.5772/17246

Downloaded: 2609

1. Introduction

With the development of high-speed switching technology, ultra-wideband (UWB) systems in high-performance wireless technology is receiving more attention. In February 2002, the Federal Communications Commission (FCC) issued a ruling that UWB systems could use an unlicensed frequency band ranging from 3.1 GHz to 10.6 GHz for data commutations, radar, and other applications so long as their radio signals satisfy a set of spectral masks for indoor and outdoor environments(Nie& Chen, 2008; Maeng et al., 2009).

However, the design of antennas for UWB applications faces many challenges. Interference is a serious problem for UWB application systems. The rejection of interference with some existing narrowband wireless services, such as IEEE 802.11a (5.15~5.825GHz) wireless local area network (WLAN) systems and IEEE 802.16 (3.3~3.8GHz) World Interoperability for Microwave Access (WiMAX) systemsare necessary for UWB application systems. One way to suppress these interfering signals is to use a spatial filter such as a frequency selective surface above the antenna. However, this approach requires too much space.

Recently, many UWB antennas have been proposed in an attempt to overcome the interference problem using frequency band rejection design. The most popular approaches for an antenna designwith frequency band rejection are embedding slots(Jyoti et al., 2010; Su et al., 2010; Zhang et al., 2010). However, most of these designs have single band-notched characteristics for the rejection of the WLAN band or WiMAX band. Only a few articles addressed the dual or multi-band rejection designs(Abdollahvand et al., 2010; Hassani et al., 2011; Mei et al., 2010; Wei et al., 2011).

Obtaining highly efficient band-notch characteristics is a challenging issue. The main problem of the frequency band rejection design is the difficulty of controlling the bandwidth of the notch band in a limited space. Furthermore, strong coupling between two adjacent notch bandsis obstacle to achieve efficient dual band-notched UWB antennas. Therefore, an efficient frequency bands rejection of the WLAN band and WiMAX band is difficult to implementfor UWB applications.

In this chapter, we proposean ultra-wideband coplanar waveguide (CPW)-fed planar monopole antenna with dual band rejection characteristics. The proposed antenna consists of a microstrip patch with U-n slot (Yang, 1999, 2002). It can achieve a wide bandwidth of 3.0~11.0GHz for voltage standing wave ratio (VSWR) of less than 2, with dual band rejection of 3.15~3.79GHz and 5.13~5.85GHz. Firstly, we present the basic structure for the proposed antenna in section 2. The simulation and measurement results will be presented in section 3 and the conclusion follows in section 4.

2. Proposed antenna

Fig. 1 shows the geometry of the proposed CPW-fed monopole antenna with dual band rejection characteristics, and the parameters of the proposed antenna are presented in Table 1. The antenna is fabricated on an inexpensive FR4 substrate with a dielectric constant of 4.4 and a thickness of 1.60 mm. A CPW transmission line with W10 = 3.00 mm and a gap distance of W11 = 1.00 mm between the single strip and two planar ground planesare used for feeding the antenna. Two ground planes, which have the same size of W9 = 17.50 mm × L10 = 29.00 mm are symmetrically placed on each side of the CPW line. The proposedantenna has anU-n slot; a n-shaped slot for band rejection with L5 = 1.2 mm, L8 = 6.0 mm, W3 = 18.0 mm, W4 = 16.0 mmand U-shaped slot with L6 = 1.2 mm, L7 = 5.0 mm, W5 = 12.0 mm, W6= 8.0 mm.

The proposed CPW-fed antenna structure is easy to implement with a printed circuit board. The CPW-feeding for the antenna in Fig. 1 is designed for 50 Ω input impedance. The use of U-n slotcan lead to produce an additional surface current path and thus we obtain ultra-wideband operations with dual band rejection characteristics.

Figure 1.

Geometry of the proposed antenna.

ParameterLength(mm)ParameterLength(mm)
W40.0L52.0
W116.0L11.0
W21.0L24.0
W318.0L39.9
W416.0L41.0
W512.0L51.2
W68.0L62.0
W71.0L75.0
W83.0L86.0
W917.5L91.8
W103.0L1029.0
W111.0L110.8
W120.2L120.2

Table 1.

Design parameters of the proposed antenna.

3. Simulation and measurement results

The electrical characteristics of the proposed antenna were simulated using the High Frequency Structure Simulator(HFSS) of Ansoft. The implementation of the CPW-fed monopole antenna with dual band rejection characteristics is shown in Fig. 2.

Figure 2.

Photograph of the implemented antenna.

The measurements of the electrical characteristics, such as the radiation patterns, VSWR and return loss, of the implemented antenna were conducted in an anechoic chamber equipped with an HP 8510C network analyzer and a far field measurement system. Fig. 3 shows the S11 and VSWR characteristics. The S11 of the design example is shown in Fig. 3(a), which demonstrates that the proposed antenna covers the frequency band of 3.0 ~ 11.0 GHz for VSWR<2, except for its dual rejection bands ranging 3.15~3.79GHz and 5.13~5.85GHz. Fig. 3(b) shows the VSWR of the design example.

Figure 3.

Simulated and measured electrical characteristics. (a) S11, (b) VSWR.

Fig. 4 shows the measured antenna gain. The maximum measured gain of the design example is about 6.13 dBi at 10.6 GHz. The measured co-polarization and cross-polarization radiation patterns of the implemented antenna in the xy-plane and xz-plane at four different frequencies are illustrated in Fig. 5. The radiation patterns show that the antenna has omnidirectional radiation characteristics.

Figure 4.

Measured results for antenna gain of the design example.

Figure 5.

Measured co-polarization and cross-polarization radiation patterns. (a) at 3 GHz, (b) at 6 GHz, (c) at 8 GHz, (d) at 11 GHz

4. Conclusion

We proposed an ultra-wideband CPW-fed planar monopole antenna with dual band rejection consisting ofU-n slot. The CPW-fed planar monopole antenna provides extremely broadband characteristics with a planar compact structure, and the U-n slot has an effect on its band rejection characteristics. The measured results for the proposed antenna show that the frequency band of 3.0~ 11.0GHz is covered for VSWR<2, except for its dual rejection band ranging 3.15~3.79GHz and 5.13~5.85GHz, which is sufficient for UWB communication. The broadband antenna design is simplified by employing a CPW feeding structure and good omnidirectional radiation patterns are obtained. The proposed antenna is suitable for use in UWB systems.

Acknowledgments

This work was supported by the University of Incheon Research Grant in 2010.

© 2011 The Author(s). Licensee IntechOpen. This chapter is distributed under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike-3.0 License, which permits use, distribution and reproduction for non-commercial purposes, provided the original is properly cited and derivative works building on this content are distributed under the same license.

How to cite and reference

Link to this chapter Copy to clipboard

Cite this chapter Copy to clipboard

Woo Chan Kim and Woon Geun Yang (August 9th 2011). Design and Implementation of UWB CPW-Fed Planar Monopole Antenna with Dual Band Rejection Characteristics, Ultra Wideband Communications: Novel Trends - Antennas and Propagation, Mohammad Matin, IntechOpen, DOI: 10.5772/17246. Available from:

chapter statistics

2609total chapter downloads

1Crossref citations

More statistics for editors and authors

Login to your personal dashboard for more detailed statistics on your publications.

Access personal reporting

Related Content

This Book

Next chapter

Design of a CPW-Fed Dual Band-Notched Planar Wideband Antenna for UWB Applications

By Fei Yu and Chunhua Wang

Related Book

First chapter

Overview of Wireless Sensor Network

By M.A. Matin and M.M. Islam

We are IntechOpen, the world's leading publisher of Open Access books. Built by scientists, for scientists. Our readership spans scientists, professors, researchers, librarians, and students, as well as business professionals. We share our knowledge and peer-reveiwed research papers with libraries, scientific and engineering societies, and also work with corporate R&D departments and government entities.

More About Us