Open access

All-Optical Wavelength-Selective Switch by Intensity Control in Cascaded Interferometers

Written By

Hiroki Kishikawa, Nobuo Goto and Kenta Kimiya

Published: 01 February 2010

DOI: 10.5772/39555

From the Edited Volume

Frontiers in Guided Wave Optics and Optoelectronics

Edited by Bishnu Pal

Chapter metrics overview

3,714 Chapter Downloads

View Full Metrics

1. Introduction

Wavelength-division-multiplexing (WDM) technology has been developing in broadband optical networks. The wavelength range used in fiber transmission systems has been increasing by employing various kinds of fiber amplifiers. In order to make it possible to handle signals of multiple wavelengths efficiently in network nodes, wavelength-selective processing in switching, routing and buffering systems will be required. In such processing systems, integrated-optic switches become one of fundamental key devices. In particular, high-speed wavelength-selective switches are required for WDM packet processing.

Wavelength-selective switches are classified from viewpoint of control method into electrically controlled devices and optically controlled ones. The former includes collinear acoustooptic (AO) devices (Goto & Miyazaki, 1990). Although multiple signals at different wavelengths can be independently switched with a single AO switch, it provides a response time only at an order of micro seconds. Optical circuits consisting of arrayed waveguide gratings (AWGs) and wavelength-insensitive switches are also regarded as a device in this class (Goh et al., 2008). The switching response depends on the control mechanizm of the wavelength-insensitive switches. The response time in thermo-optic switches is an order of milli seconds (Suzuki et al., 1998). On the other hand, optically controlled switches include devices using phase shift induced by optical nonlinear Kerr effect (Doran & Wood, 1988) and phase shift in semiconductor optical amplifiers (SOAs) (Nakamura et al., 2000) and in quantum dots (Kitagawa et al., 2009). These switches using phase shifting, in general, cannot provide wavelength-selectivity. Therefore, to realize wavelength-selective switching of the latter class, combination with multiplexers and demultiplexers such as AWGs is required.

As a switch of the latter class, the authors have proposed a new type of wavelength-selective switch where optical amplitudes in waveguide arms of interferometers are controlled by Raman amplifiers (Kishikawa & Goto, 2005; Kishikawa & Goto, 2006; Kishikawa & Goto, 2007a; Kishikawa & Goto, 2007b). In this article, the operation principle of wavelength-selective switching with the proposed devices is described. Computer simulation by finite-difference beam-propagation-method (FD-BPM) is performed to verify the switching operation.

Advertisement

2. Wavelength-selective switching by light control

Optical switching circuits discussed in this article consist of directional couplers, waveguide-type Raman amplifiers and attenuators as shown in Fig. 1. Designing of the switching circuits indicated by the dotted rectangular is theoretically discussed in the next section. In the switching circuits, the signal light intensity is controlled with waveguide-type Raman amplifiers. We consider that WDM optical signals at wavelengths λ 1, λ 2 and λ 3 are incident into the upper waveguide of the circuit, and the two signals at λ 1 and λ 3 are to be switched to OUT B, whereas the signal at λ 2 is to be forwarded to OUT A. To induce this routing operation, optical pumping signals at λ 1' and λ 3' are injected to Raman amplifiers, where λ i ', i=1,2,3, is shorter than λ i by an amount of a Raman shift λ R, that is, λ i '= λ i - λ R. The Raman shift depends on the material of the amplifier, whose typical value is approximately 100 nm. By injecting these pumping signals, the Raman amplifiers amplify wavelength-selectively the signals at λ 1 and λ 3. In some structures of the circuits, control signal λ 2' may be injected to another Raman amplifier placed in the circuits. We will find the structure of switching circuits with the required conditions for the amount of amplification. Since the Raman amplifiers are controlled by pumping light, all-optical switching can be realized.

Figure 1.

Wavelength-selective switching circuit using a combination of optical couplers, optical Raman amplifiers and optical attenuators.

Figure 2.

Wavelength-selective amplification by stimulated Raman scattering with waveguide-type Raman amplifiers.

The wavelength-selective amplification can be performed in wide wavelength range by employing stimulated Raman scattering as shown in Fig. 2. The Raman gain bandwidth Δf R in frequency for a specific pumping wavelength is tens GHz, for example, Δf R =20 GHz with pulse-pumped maximum gain of 20 dB and continuous wave (cw)-pumped gain of 3.7 dB at λ =960 nm in GaP waveguides (Suto et al., 2002). In a Si waveguide, Δf R =75 GHz with cw-pumped gain of 2.3 dB at wavelength 1574 nm (Rong et al., 2004), and pulse-pumped gain of 20 dB at wavelength 1673 nm (Raghunathan et al., 2005) were reported.

We denote the wavelength range available for this device as Δλtotal. Then, the WDM number handled with this switch is expressed as N WDM = Δλtotal / Δλ R = c Δλtotalf R λ 2, where c is the light velocity and Δλ R is the Raman gain bandwidth in wavelength. If Δλtotal is as wide as 40 nm with the center wavelength of λ=1550 nm, N WDM can be as large as 65 with Si Raman amplifiers.

Advertisement

2. Theoretical analysis of switching

2.1. Key elements

Figure 3.

Key elements consisting the proposed wavelength-selective switches.

This section describes theoretical analysis with ideal device models. Key elements consisting the proposed switch are a 3-dB directional coupler and parallel independent waveguides containing amplifiers or attenuators as shown in Fig. 3. In the 3-dB directional coupler shown in (a), the electric field amplitude E out (i), i=1, 2, of the optical output signals are related with E in (i) of the optical input signals from the coupled mode theory, by eliminating the common phase term along the propagation, as

( E o u t ( 1 ) E o u t ( 2 ) ) = ( cos ( π κ / 4 κ 0 ) j sin ( π κ / 4 κ 0 ) j sin ( π κ / 4 κ 0 ) cos ( π κ / 4 κ 0 ) ) ( E i n ( 1 ) E i n ( 2 ) ) E1

where j = 1 κ and κ 0 are the coupling coefficient and the coefficient at a designed wavelength for 3-dB coupling. The value κ depends on the field overlapping of optical individual waveguides. The wavelength dependence of κ therefore depends on the waveguide structure. This wavelength dependence of the 3-dB directional coupler causes the wavelength dependency in the proposed switch. At the designed wavelength for the 3-dB coupling, eq.(1) is simplified by using κ = κ 0, as

( E o u t ( 1 ) E o u t ( 2 ) ) = 1 2 ( 1 j j 1 ) ( E i n ( 1 ) E i n ( 2 ) ) E2

Optical waves propagated along the independent parallel waveguides with amplification coefficient α 1 and α 2 are expressed as

( E o u t ( 1 ) E o u t ( 2 ) ) = ( α 1 0 0 α 2 ) ( E i n ( 1 ) E i n ( 2 ) ) E3

2.2. Switch A

We have proposed two switch architectures. Figure 4 shows the device structure of one of the switch architectures, named as switch A. The switch consists of two cascaded interferometers. In the first interferometer, each arm has a Raman amplifier with amplification coefficient αA and αB for the lower and upper arms, respectively. An attenuator with attenuation coefficient β is placed in the upper arm of the second interferometer. The Raman amplifiers are pumped by backward traveling light coupled with polarization-selective or wavelength-selective couplers.

Figure 4.

Schematic diagram of the proposed wavelength-selective switch A consisting of two cascaded interferometers.

Optical WDM signals at wavelength λ i, i=1,..., N, are incident at input port I A. When optical WDM signals at λ k , k { 1, ..., N } , are to be switched to output port O B, pumping WDM lights at λ k ' are coupled to the lower Raman amplifier to amplify the signals with gain coefficient αA. The wavelength λ k ' satisfies the condition λ k '= λ k - λ R. On the contrary, when the WDM signals at λ j are to be switched to output port O A, pumping WDM lights at λ j ' are coupled to the upper Raman amplifier to amplify the signals with gain coefficient αB. Since the Raman amplifiers made of crystalline waveguides can wavelength-selectively amplify optical signals with narrow gain bandwidth ΔλR, multiple WDM signals can be simultaneously and wavelength-selectively switched with this single switch.

Using eqs.(2) and (3), the output fields through the switch are related to the input fields as

( A o u t B o u t ) = ( 1 2 ) 3 ( 1 j j 1 ) ( 1 0 0 β ) ( 1 j j 1 ) ( α A 0 0 α B ) ( 1 j j 1 ) ( A i n B i n ) E4

Since the incident optical signal is coupled into the lower port I A, we assume

( A i n B i n ) = ( E i n 0 ) E5

By substituting eq. (5) into eq. (4), the outputs are obtained as

( A o u t B o u t ) = E i n 2 2 ( α A α B β ( α A + α B ) j [ α A α B + β ( α A + α B ) ] ) E6

It is expected from eq. (6) that B out =0 for some values of αA, αB and β, on the other hand, A out =0 for some other values of these parameters. Since the number of these unknown parameters is three for two equations, the solutions for these parameters cannot be determined. However, by considering physical limitations in these parameters, we obtain the solutions as

( A o u t B o u t ) = { ( E i n 0 ) w h e n { α A = 1 α B = 1 + 2 β = 1 1 + 2 ( 0 E i n ) w h e n { α A = 1 + 2 α B = 1 β = 1 1 + 2 E7

It is found from eq.(7) that the switch operates as a 1x2 spatial switch whose output port is selected by proper amplification and attenuation effects. It is noted that the value β is constant in these two conditions. The incident light is routed to output port O A by amplifying the upper amplifier with α B = 1 + 2 . The amplification is not required in the other amplifier α A. On the contrary, the light is routed to output port O B by amplifying the lower amplifier with α A = 1 + 2 . A drawback of this architecture is that either amplifier has to be activated for an input signal. That is, there is no default single output path without pumping.

2.3. Switch B

Figure 5.

Schematic diagram of the proposed wavelength-selective switch B consisting of three cascaded interferometers.

An alternative architecture of the switch consists of cascaded three interferometers as shown in Fig. 5. Three Raman amplifiers are placed in the lower arms of the three interferometers. The feature of this architecture is that optical incident signals are routed to output port O A without any pumping light for amplification, and are switched to output port O B only when three amplifiers are activated by pumping. Since the three amplifiers are activated to have the same amplification coefficient α, the control for switching is simpler than that in switch A. The output fields through this switch are related to the input fields as

( A o u t B o u t ) = ( 1 2 ) 4 ( 1 j j 1 ) ( α 0 0 1 ) ( 1 j j 1 ) ( α 0 0 1 ) ( 1 j j 1 ) ( α 0 0 1 ) ( 1 j j 1 ) ( A i n B i n ) E8

Since the incident optical signal is coupled into the lower port I A, we assume

( A i n B i n ) = ( E i n 0 ) E9

By substituting eq. (9) into eq. (8), the outputs are obtained as

( A o u t B o u t ) = E i n 4 ( α 3 3 α 2 α 1 j [ α 3 α 2 α + 1 ] ) E10

For no amplification at each Raman amplifier, that is α=1, output electric fields are calculated to be A out = - E in and B out =0. It means that the incident optical wave is routed to output port O A without amplification. In contrast, to switch the wave from output O A to output O B, the output electric fields have to be A out =0 by proper amplification. The condition is given as a solution of an equation α3-3α2-α-1=0. This solution for α can be satisfied with α=3.383. With this value of α, B out is calculated to be –j(α+1)(α-1)2 E in = –j6.222 E in . It means that the incident optical wave is amplified and routed to output O B. This switching operation is summarized as

( A o u t B o u t ) = { ( E i n 0 ) w h e n α = 1 ( 0 j 6.222 E i n ) w h e n α = 3.383 E11

The difference of the output intensity by a factor of (6.222)2 can be compensated by employing an attenuator at output port O B or an amplifier at output port O A.

Advertisement

3. Numerical simulation of switching

3.1. Switch A

The switching characteristics can be analyzed using the equations described in the previous section. Wavelength dependence is also found by using eq. (1) instead of eq.(2) in the similar manner as described above. In this section, on the contrary, we verify the switching operation by numerical simulation to clarify the wave propagation along the waveguides of the switch. We use FD-BPM simulation with seventh-order Pade approximation (Hadley, 1992).

Figure 6.

Two-dimensional model of switch A for FD-BPM simulation.

We consider a two-dimensional slab waveguide model as shown in Fig. 6. The step length and the step width in the lateral direction are Δz=1.0 μm and Δx=0.05 μm, respectively. As the waveguide material, we consider silica waveguides. The core and cladding regions have refractive indices of n c=1.461 and n s=1.450, respectively. The width of the waveguide is W=3.0 μm. The interval and the length of the coupled region are set to be d=3.2 μm and L c=100 μm to realize 3-dB coupling at wavelength 1550 nm. The length of the parallel waveguides corresponding to the Raman amplifiers and the attenuator is L p=50 μm. The branching waveguides have the length of L s=1025 μm. The distance between the two input ports is D=26.5 μm. The total length is L=6.65 mm.

Figure 7.

Distribution of optical fields with two different switching conditions in swith A.

The switching operation at λ=1550 nm is confirmed as shown in Fig.7, where squared electric fields |E|2 are plotted. In this simulation, Raman amplification is equivalently simulated just by increasing the optical electric field by multiplying the gain coefficient αA or αB at a place located at the end of the waveguide region for the amplifier. In a similar manner, the attenuator is modelled by multiplying the optical electric field by β at the beginning of the attenuator.

The wavelength dependence of the output intensity with the switch is plotted in Fig. 8. At the designed wavelength λ=1550 nm, the switching extinction ratio is larger than 35 dB. The wavelength range to achieve an extinction ratio larger than 20 dB is approximately 40 nm, though the 10-dB extinction ration is obtained over 100 nm. This wavelength dependence is caused by the wavelength dependence of the directional couplers.

Figure 8.

Wavelength dependence of switched outputs for the switch A designed at wavelength λ=1550nm.

3.2. Switch B

The switching operation with switch B is also verified by FD-BPM simulation. The model used in the simulation is shown in Fig. 9. The total length of the switch is L=8.85 mm.

Figure 9.

Two-dimensional model of switch B for FD-BPM simulation.

Figure 10.

Distribution of optical fields with two different switching conditions in swith B.

The switching operation at λ=1550 nm is confirmed as shown in Fig. 10. Although the output intensities from output port O A and O B are different, switching is successfully simulated.

The wavelength dependence is shown in Fig. 11. At the designed wavelength λ=1550nm, the switching extinction ratio is larger than 25 dB. The wavelength range to achieve the extinction ratio larger than 20 dB is approximately 30 nm, though the 10-dB extinction ration is obtained over 80 nm.

Figure 11.

Wavelength dependence of switched outputs for the switch B designed at wavelength λ=1550nm.

Advertisement

4. Improvement of wavelength dependency

Waveguide-type Raman amplifiers do not depend on wavelength bands to be used because stimulated Raman scattering which is the base effect of Raman amplification can occur at any wavelength bands. Meanwhile, 3dB couplers have wavelength dependency in general, that is, the function of dividing an incident optical wave into two waves at the rate of 50:50 is available at some particular wavelength bands. The main cause of the wavelength dependency is the wavelength dependence of the coupling coefficient κ in eq.(1). For improving the characteristics of wavelength dependency of the switch and utilizing it at any wavelength bands, wavelength-independent (or wavelength-flattened) optical couplers should be employed. Fiber-type wavelength-independent couplers, that can be used for 50:50 of the dividing rate at wavelength bands such as 1550 nm± 40 nm and 1310 nm ± 40 nm, have already been on the market. However, waveguide-type wavelength-independent couplers have advantage from the viewpoint of integrating the switch elements.

An alternative for improving wavelength dependence is to replace the directional couplers by asymmetric X-junction couplers (Izutsu et al., 1982; Burns & Milton, 1980; Hiura et al., 2007). The asymmetric X-junction coupler has basically no dependence on wavelength and helps to improve the wavelength dependency of the proposed switch (Kishikawa et al., 2009a; Kishikawa et al., 2009b).

Advertisement

5. Another issue in implementation

Phase shift of the signal pulse experienced in the waveguide-type Raman amplifiers should be discussed because it can impact the operation of the switch. The phase shift is induced from refractive index change caused by self-phase modulation (SPM), cross-phase modulation (XPM), free carriers generated from two-photon absorption (TPA) (Roy et al., 2009), and temperature change. Although the structure of the switch becomes more complex, the effect of SPM and TPA-induced free carriers can be cancelled by installing the same nonlinear waveguides as those of the waveguide-type Raman amplifiers into counter arms of the Mach-Zehnder interferometers of the switch. The influence of XPM and temperature change involved with high power pump injection can also be suppressed by injecting pump waves, having the same power and different wavelengths that do not amplify the signal pulse, into the counterpart nonlinear waveguides.

Advertisement

6. Conclusion

We proposed a novel all-optical wavelength-selective switching having potential of a few tens of picosecond or faster operating speed. We discussed the theory and the simulation results of the switching operation and the characteristics. Moreover, the dynamic range over 25dB was also obtained from the simulation results of the switch. This characteristics can be wavelength-selective switching operation. More detailed analysis and simulation taking the nonlinearity of Raman amplifiers into account are required to confirm the operation with actual devices.

Although the principle and the fundamental verification were performed with the switches consisting of directional couplers, the idea can be similarly applied to switches consisting of other components such as asymmetric X-junction couplers to increase the wavelength range.

References

  1. 1. Doran N. J. Wood D. 1988 Nonlinear-Optic Loop Mirror, Optics Lett., 13 1 56 58 , Jan. 1988.
  2. 2. Burns W. K. Milton A. F. 1980 An Analytic Solution for Mode Coupling in Optical Waveguide Branches, IEEE J. Quantum Electron., QE-16 , 4 446 454 , Apr. 1980.
  3. 3. Goh T. Kitoh T. Kohtoku M. Ishii M. Mizuno T. Kaneko A. 2008 Port Scalable PLC-Based Wavelength Selective Switch with Low Extinction Loss for Multi-Degree ROADM/WXC, The Optical Fiber Communication Conference and the National Fiber Optic Engineers Conference (OFC/NFOEC2008), San Diego, OWC6, Mar. 2008.
  4. 4. Goto N. Miyazaki Y. 1990 Integrated Optical Multi-/Demultiplexer Using Acoustooptic Effect for Multiwavelength Optical Communications, IEEE J. on Selected Areas in Commun., 8 6 1160 1168 , Aug. 1990.
  5. 5. Hadley G. R. 1992 Wide-Angle Beam Propagation Using Pade Approximant Operators, Opt. Lett., 17 20 1426 1428 , Oct. 1992.
  6. 6. Hiura H. Narita J. Goto N. 2007 Optical Label Recognition Using Tree-Structure Self-Routing Circuits Consisting of Asymmetric X-junction, IEICE Trans. Commun., E90-C , 12 2270 2277 , Dec. 2007.
  7. 7. Izutsu M. Enokihara A. Sueta T. 1982 Optical-Waveguide Hybrid Coupler, Opt. Lett., 7 11 549 551 , Nov. 1982.
  8. 8. Kishikawa H. Goto N. 2005 Proposal of All-Optical Wavelength-Selective Switching Using Waveguide-Type Raman Amplifiers and 3dB Couplers, J. Lightwave Technol., 23 4 1631 1636 , Apr. 2005.
  9. 9. Kishikawa H. Goto N. 2006 Switching Characteristics of All-Optical Wavelength-Selective Switch Using Waveguide-Type Raman Amplifiers and 3-dB Couplers, IEICE Trans. Electron., E89-C , 7 1108 1111 , July 2006.
  10. 10. Kishikawa H. Goto N. 2007a Optical Switch by Light Intensity Control in Cascaded Coupled Waveguides, IEICE Trans. Electron., E90-C , 2 492 498 , Feb. 2007.
  11. 11. Kishikawa H. Goto N. 2007b Designing of Optical Switch Controlled by Light Intensity in Cascaded Optical Couplers, Optical Engineering, 46 4 pp.044602-1-10, Apr. 2007.
  12. 12. Kishikawa H. Kimiya K. Goto N. Yanagiya S. 2009a All-Optical Wavelength-Selective Switch Controlled by Raman Amplification for Wide Wavelength Range, Optoelectronics and Communications Conf., OECC2009, Hong Kong, TuG3, July 2009.
  13. 13. Kishikawa H. Kimiya K. Goto N. Yanagiya S. 2009b All-Optical Wavelength-Selective Switch by Amplitude Control with a Single Control Light for Wide Wavelength Range", Int. Conf. on Photonics in Switching, PS2009, Pisa, PT-12, Sept. 2009.
  14. 14. Kitagawa Y. Ozaki N. Takata Y. Ikeda N. Watanabe Y. Sugimoto Y. Asakawa K. 2009 Sequential Operations of Quantum Dot/Photonic Crystal All-Optical Switch With High Repetitive Frequency Pumping, J. Lightwave Technol., 27 10 1241 1247 , May 2009.
  15. 15. Nakamura S. Ueno Y. Tajima K. Sasaki J. Sugimoto T. Kato T. Shimoda T. Itoh M. Hatakeyama H. Tamanuki T. Sasaki T. 2000 Demultiplexing of 168-Gb/s Data Pulses with a Hybrid-Integrated Symmetric Mach-Zehnder All-Optical Switch, IEEE Photon. Tech. Lett., 12 4 425 427 , Apr. 2000.
  16. 16. Raghunathan V. Boyraz O. Jalali B. 2005 20dB On-Off Raman Amplifiation in Silicon Waveguides, Conf. Lasers and Electro-Optics (CLEO2005), Baltimore, CMU1, May 2005.
  17. 17. Rong H. Liu A. Nicolaescu R. Paniccia M. Cohen O. Hak D. 2004 Raman Gain and Nonlinear Optical Absorption Measurements in a Low-Loss Silicon Waveguide, Appl. Phys. Lett., 85 12 2196 2198 , Sept. 2004.
  18. 18. Roy S. Bhadra S. K. Agrawal G. P. 2009 Raman Amplification of Optical Pulses in Silicon Waveguides: Effects of Finite Gain Bandwidth, Pulse Width, and Chirp, J. Opt. Soc. Am. B, 26 1 Jan. 2009.
  19. 19. Suto K. Saito T. Kimura T. Nishizawa J. Tanabe T. 2002 Semiconductor Raman Amplifier for Terahertz Bandwidth Optical Communication, J. Lightwave Technol., 20 4 705 711 , Apr. 2002.
  20. 20. Suzuki S. Himeno A. Ishii M. 1998 Integrated Multichannel Optical Wavelength Selective Switches Incorporating an Arrayed-Waveguide Grating Multiplexer and Thermooptic Switches, J. Lightwave Technol., 16 4 650 655 , Apr. 1998.

Written By

Hiroki Kishikawa, Nobuo Goto and Kenta Kimiya

Published: 01 February 2010