Open access peer-reviewed chapter

Bioavailability of High Molecular Weight Polycyclic Aromatic Hydrocarbons Using Renewable Resources

By Olusola Solomon Amodu, Tunde Victor Ojumu and Seteno Karabo Obed Ntwampe

Submitted: May 23rd 2012Reviewed: October 29th 2012Published: February 7th 2013

DOI: 10.5772/54727

Downloaded: 2007

1. Introduction

Polycyclic aromatic hydrocarbons (PAHs) are the world’s largest class of carcinogens known to date, not only because of their ability to cause gene mutation and cancer, but due to their persistency in the environment. They are particularly recalcitrant due to their molecular weight, hydrophobic nature and thus, accumulate in various matrices in the environment.

PAHs, also known as polyarenes or polynuclear aromatic hydrocarbons, are formed and released into the environment through natural and anthropogenic sources. Natural sources include volcanoes and forest fires while anthropogenic sources include, majorly, incomplete combustion of fossil fuels, wood burning, municipal and industrial waste incineration. PAHs containing two or three fused benzene rings are classified as low molecular weight (LMW) PAHs and are more water soluble while those with four or more benzene rings are referred to as high molecular weight (HMW) PAHs. They tend to adsorb onto soil and sediment thus, making them recalcitrant in the environment. Sixteen of these organic compounds have been identified as priority pollutants due to their hazardous properties, with HMW PAHs being considered as potential human carcinogens, by the United State Environmental Protection Agency [1].

The cost of biodegradation technology and the low bioavailability including mass transfer limitations of PAHs, especially those with high molecular weight, from several matrices into the aqueous phase for effective enzyme-based microbial biodegradation still constitute major challenges. However, current research efforts have focused on the combined use of biosurfactants and enzymes produced from renewable resources such as agricultural by-products and/or agro-industrial waste, through assisted biostimulation and bioaugmentation, for biodegradation of PAHs. Such methods are relatively inexpensive and less invasive as compared to physico-chemical remediation processes [2-4]. The application of crude biosurfactants produced by Pseudomonas ssp., Rhodococcus ssp. and several others, have been observed to achieve a high mobilization rate of PAHs from contaminated environmental matrices [5, 6].

The synergistic effect of biostimulation combined with bioaugmentation using fungal strains of Rhizopus spp., Penicillium spp. and Aspergillus spp., isolated from PAH contaminated soil, significantly improve the overall bioavailability for the biodegradation of PAHs in comparison to biostimulation alone [7]. Additionally, several other renewable resources have been used as sources of both carbon and nitrogen by several microorganisms during the expression of biosurfactants thus enhancing PAH bioavailability and enzymatic biodegradation [8-11]. This review describes the environmental behavior of PAHs, and how it affects bioavailability. It also examines the effectiveness of microorganisms used in the production of crude biosurfactants for the biodegradation of HMW PAHs rather than the direct application of refined extracts, with a view to minimize the cost associated with enzymatic biodegradation. The chapter further discusses the effects of bioavailability on the biodegradation of HMW PAHs; bioavailability kinetics to quantitatively estimate PAHs bioavailability using different microorganisms; and enhanced biodegradation of PAHs using crude biosurfactants from renewable resources.

2. Bioavailability of HMW PAHs

2.1. PAHs bioavailability — Definitions and intrinsic factors

Polycyclic aromatic hydrocarbon mobilization and biodegradation are contingent upon their bioavailability from various matrices. Given the legal and regulatory implications of the bioavailability concept as part of a risk assessment framework, the term must be clearly understood in order to establish the minimum level permissible for contaminants like PAHs in the environment. The understanding of bioavailability is also important to be able to assess and evaluate the overall success of PAHs biodegradation. Researchers, however, differ in their opinion as to what the exact definition of bioavailability should be [12].

The following definitions for bioavailability were compiled in Technical Reports published by the European Centre for Ecotoxicology and Toxicology of Chemicals [13] and the United State National Research Council [14]: (i) “The ability of a substance to interact with the biosystem; (ii) “The fraction of the contaminants in the environment that is potentially available for biological action” [15]; (iii) “The amount/percentage of a compound that is actually taken up by an organism as the outcome of a dynamic equilibrium of organism-bound sorption processes, and soil particle-related exchange processes, all in relation to a dynamic set of environmental conditions” [16]; (iv) “The fraction of a chemical accessible to an organism for absorption, the rate at which a substance is absorbed into a living system, or a measure of the potential to cause a toxic effect”. In pharmacology and toxicology, the term relates to the systemic availability of a xenobiotic after intravenous or oral dosing [17]. Although these concepts are useful, making direct parallels from the pharmacological usage to contaminants in soil and sediment or biota can be problematic. For example, microorganisms do not have a digestive tract, target organs, or a circulatory system [13]. These concepts may also not be appropriate as contaminants in soil or aquatic environments, being controlled by, for example, the rate of desorption and mobilization from solid matrices, are often continuously supplied to organisms gradually rather than at an acute dose. Environmental scientists often consider bioavailability to represent the accessibility of a soil-bound chemical for assimilation and possible toxicity [18, 19] and thus, have tried to adapt the use of bioavailability concept when considering human exposure to soil-borne contaminants. For example, Ruby [20] including Kramer and Ryan [21] suggested that the bioavailable portion is the amount of compound that is removed from soil through desorption processes under physiological conditions. Another view of bioavailability is represented by the contaminant crossing a cell membrane, entering a cell, and becoming available at a site of biological activity. Others might think of bioavailability more specifically in terms of contaminant binding to or release from a solid phase.

Obviously, the different definitions of the term bioavailability by scientists in various disciplines are capable of causing semantic confusion and thus, garner more attention than proffering solution to its challenges. The authors, in this chapter, have compiled these opinions in order to present a simple and workable definition to the term bioavailability as it is important to estimateF; the extent of contaminants desorption from the sorbed phase, the non-aqueous phase residue as against the minimum level required in the environment for such contaminants, and thus assessing the overall success of biodegradation. Considering these opinions about bioavailability, two words are common to almost all, which are; uptake or absorbed and available. Based on this observation, bioavailability can be defined as the amount of available contaminants in the environment that can be absorbed by microorganisms and /or biological products. Other clauses such as the fraction of contaminants taken up or absorbed, the fraction of contaminant that is potentially available, the mobilization or transportation of contaminants from the sorbed phase, the amount desorbed from the soil matrices, etc., which are often included in the definition of bioavailability and thus causing confusion, are intrinsic factors or features of bioavailability. However, these intrinsic factors are influenced by the physico-chemical properties of the contaminants and those of the sorbent.

Hence, studies on bioavailability are very crucial in order to link the quantity of PAHs taken up by microorganism with the actual amounts that are available to cause adverse effects in the environment. Many factors have been known to affect PAH bioavailability, which are [12, 22, 23];

  • Physical and chemical properties of PAHs,

  • Soil properties (soil organic matter, dissolved organic matter, moisture content, etc.),

  • Aging of PAHs in soil and receptor microorganism.

2.2. Effects of physical and chemical properties of PAHs on bioavailability

Bioavailability is influenced by the molecular structure and size of PAHs. LMW PAHs are removed faster by physico-chemical and biological processes due to their higher solubility, volatility and the ability of many microorganisms to use them as sole carbon sources in comparison to the HMW PAHs [24]. Bioavailability changes with time and weathering [25]. Aging is a central part concerning availability and refers to the process of organic compounds in soil becoming less susceptible to degradation, extractability and other related processes in a time dependent manner [26, 18]. Aging increases sorption propensity of soil contaminants making them more recalcitrant to diffusion and mobility which consequently lead to low bioavailability. Both the physico-chemical properties of the contaminant and the soil characteristics influence aging, which may include several steps and processes such as oxidation thus incorporating the contaminant into natural organic matter [27, 28], slow diffusion into small pores and absorption into organic matter, or entrapment due to the formation of semi-rigid films around non-aqueous-phase liquids (NAPL) with a high resistance toward NAPL-water mass transfer [29].

2.3. Effects of soil or sediment and dredging properties on PAHs bioavailability

Soil properties such as organic matter content, soil texture, soil depth, particle size, pH, porosity, intrinsic permeability, liquid limit, and cation exchange capacity, influence PAH bioavailability. Soil properties can vary greatly from one region to another. They can even vary within the same region spatially and with depth [30]. Microorganisms have different levels of tolerance to these factors, which affect their growth and other metabolic activities. Soil structure such as aggregation has been found to decrease PAH availability through physical sequestration of PAHs in the interior of aggregates [31]. For instance, Nam et al. [32] found that PAH bioavailability to phenanthrene degraders declined with time in soils which had more than two percent organic matter. Hundal et al. [33] reported on the retention of large amounts of phenanthrene by smectite clays. Yang et al. [34] investigated the impact of soil organic matter on PAHs distribution in soils and reported that when the soil organic matter was increased from 0.2 to 7.1% the average non-bioavailable amount of acenaphthene, anthracene, fluoranthene, and pyrene were almost tripled from 436.9 to 1205.8 ng/g.

2.4. Effects of mass transfer on bioavailability of HMW PAHs

The overall PAHs biodegradation can be conceptually divided into the following steps: desorption to the eqeuous phase; mass transfer to biologically accessible regions; and biological uptake and transformation [35, 18], as shown in Figure 1. These steps occur sequencially, such that the overall biodegradation rate can be controlled by any of these steps. Given the sequential nature of the process, the impact of desorption rate on overall biodegradation is expected to be greatest in the case where biodegradation rates are higher relative to desorption rates. This occurs when the active microorganisms are capable of high biodegradation rates and either the media is porous thus having a high capacity for the solute, or media has large diffusion distances [36, 37]. Based on this, it is important to examine how the physical morphology of surface and subsurface soils can impact the biodegradation of sorbed organic chemicals. Naturally, soil contains porous particles of different sizes, many of which are smaller than the size of microorganisms. For example, analysis of one of the coarser sand sizes from the Borden aquifer in Ontario (Canada), indicated that, roughly 50% of the intraparticle pore volume resides in pores that are less than 0.1 µm in diameter [38].

Figure 1.

Diffusion of entrapped PAH out of soil micropores into aqueous phase to become available to microorganism.

Pores with diameter larger than 1 µm comprised about 12% of the total pore space, and only about 5% of the pore volume was attributed to pores larger than 2 µm. Considering that most indigenous bacteria found in soil are 0.5 to 1.0 µm in diameter [39], bacteria will be physically excluded from attaching to intraparticle pores of these grains. The mean diameter of intraparticle pores occupied by bacteria has been estimated to be typically larger than 2 µm [40], and this is likely to be larger than intraparticle porespaces of many natural sorbent solids. However, for those pores which are accessible to bacteria, slow mass transfer of contaminants from the pore interior as well as from the pore surface can limit the extent of microbial growth and consequently biodegradation.

3. Kinetic models and assessment of bioavailability of PAHs

3.1. First–order kinetics

Biodegradation rate of PAHs in the aqueous phase and the rate constant (k) can be determined using the reaction rate expression as follows:

-dCdt=kCnE1

C - is the concentration of PAH (mg/l), t the time (days), k the rate constant for chemical disappearance of PAH (days-1) and n, the reaction order, which is unity for first order kinetics [24, 41]. Based on the assumptions that only dissolved forms are available for biodegradation and that the biodegradation rate follows a first order kinetics [42], the logarithm of the ratio of residual PAH concentration to its initial (i.e., logarithm of C/Co) can be plotted as a function of time and hence, the biodegradation rate being the gradient of the plot, can be determined.

3.2. Michaelis-Menten kinetic model

The most commonly assumed relationship for the assessment of bioremediation is done using the biodegradation rate and the concentration (C) of the contaminants in the aqueous phase using the Michaelis-Menten kinetic model or Monod equation:

V=(VmaxS)(Km+ S) E2

where V is the biodegradation rate, Vmax the maximum biodegradation rate, Km the Michaelis-Menten constant, and S the residual contaminant concentration. As depicted in Figure 2, at high S, V becomes independent of S and at low S, the equation is approximated to first order kinetics, i.e., V is directly proportional to S. At all values of S, V is always proportional to the biocatalyst concentration available for the biodegradation process.

Figure 2.

Michaelis-Menten kinetics rate profiles.

At low PAH concentrations, such as when the concentration of the contaminant is in the part per billion ranges usually encountered for underground water contaminations, insufficient energy and carbon source availability can become a limiting factor for microbial growth and maintenance. That is, a threshold may exist below which microbial biomass growth cannot be sustained. Such a minimum concentration for sustainable growth is defined as the concentration at which microbial growth is balanced by decay [36, 43]. Also at such a concentration, the biodegradation rate reverts back to that described by first-order kinetics. However, the application of suitable microorganisms and/or their products can be used to enhance the concentration of PAH in the aqueous phase through increasing the desorption rate and mobilization from the sorbed phase. At such an enhanced concentration, Michaelis–Menten rate kinetics becomes appreciably applicable and from its linearized plot (Figure 3), the maximum PAH degradation rate can easily be determined. The rate equations can also be simplified by making certain assumptions. Particularly, the steady-state approximation which assumes a negligible change in the concentration of the enzyme-substrate complex during the course of the reaction. Furthermore, the Michaelis–Menten reaction mechanism presupposes that catalysis is irreversible and that the enzyme is not subject to any product inhibition. This limits the suitability of using this model to predict biodegradation rates where chemical surfactants have been known to inhibit product formation [44].

Figure 3.

A plot of the linearized form of Michaelis-Menten rate equation.

3.3. Freundlich adsorption isotherm

The Freundlich isotherm is an adsorption isotherm which relates the concentration of a solute on the surface of an adsorbent to the concentration of the solute in the liquid with which it is in contact. The isotherm is mathematically represented as:

Q=xm kC1nE3

For which the linearized form is:

logQ = logk+ NlogC    [ N= 1n]E4

where Q is the sorbed amount of PAH (mg/g soil), x the mass of PAH (mg), m the mass of soil (g), C the equilibrium concentration of PAH in solution (mg/l), k and n are constants for a given PAH and adsorbent, which can be either a solid or a liquid, at a particular temperature and thus define the isotherm’s curvature. The amount of the sorbed PAH can be determined by plotting the isotherms’ linearized form as a function of the equilibrium concentration of the PAH in solution (Figure 4).

Figure 4.

A plot of the linearized form of the Freundlich isotherm.

The isotherm can also be represented in terms of sorbent pore pressure P as:

Q=kP1nE5

At high pressure, the extent of adsorption is independent of pressure (i.e. 1/n = 0), at low pressure, it is dependent on pressure.

In a recent study of biodegradation of phenanthrene and pyrene in a slurry soil system using Phanerochaete chrysosporium, biosorption isotherms were found to fit well with the Freundlich isotherm. The Freundlich n values were approximated to unity, indicating that the biosorption was dominated by partitioning onto fungal biomass and the soils’ organic matter [45, 46]. It also showed that the amount of PAH sorption by the microbial biomass was dependent on the concentration of the PAH present in the contaminated medium. The extent of adsorption varied directly with pressure until saturation pressure is reached. Beyond that point, the rate of adsorption reaches a maximum, even after applying higher pressure [47], thus the Freundlich adsorption isotherm will not be suitable at a higher pressure. Although, Langenfeld et al. [48] has shown that pressure variation has no effect on the supercritical extraction efficiency of PAHs, the use of Freundlich isotherm in biodegradation studies without considering the effects of pore pressure on sorption of HMW PAHs [45] can be problematic.

3.4. Enhanced bioavailability model

Zhang et al. [36] proposed a bioavailability model that can be used to quantitatively estimate the impact of sorption on the biodegradation by taking a mass balance for organic compounds in a batch system containing liquid and solids and substituting the expression into the Michaelis-Menten rate equation. The model assumed that only the organic contaminant in the liquid phase is biodegradable. Park et al. [49] extended the model using formulations for reversible and instantaneous sorption–desorption processes with first-order biodegradation reactions in both liquid and solid phases, including the assumption that the liquid-phase degradation rate coefficient is not affected by the presence of solids. Under the sorption–desorption equilibrium assumption, the liquid-phase contaminant disappearance rate can be expressed as:

dCdt= EfBfk1CE6

Using integration, the concentration of PAHs in the aqueous phase at any particular time during the biodegradation process can be determined as:

C= C0exp(EfBfk1t)E7

where, Ef is the enhanced transformation factor (dimensionless);

Ef=1+RslKdfsks/k1E8

Bf is the bioavailability factor;

Bf=1(1+RslKd)E9

Rsl is solid/liquid ratio (mg/l);

Rsl=mV1E10

where C is the liquid-phase concentration of contaminant (mg/l), C0 the initial liquid-phase concentration (mg/l), t time (min), k1 the first-order liquid-phase degradation rate coefficient (min-1) which can be determined from biodegradation assay, Kd the sorption distribution coefficient (dimensionless), fs the fraction of attached biomass in the system (dimensionless), ks the first-order sorbed-phase degradation rate (min-1), m the sorbent mass (g), and Vl is the liquid volume (l).

The bioavailability factor (Bf) range from the above equation is between zero and unity. A Bf approaching unity indicates that the effect of sorption is practically negligible while a Bf tending towards zero shows that biodegradation will be significantly limited by sorption [36]. On the other hand, if there is no sorbed-phase degradation by the attached biomass, Ef is unity and the enhanced bioavailability model reduces to bioavailability model which assumes sorption-desorption and only liquid-phase biodegradation. An Ef > 1 indicates that biodegradation is faster than that expected based on the liquid-phase degradation while Ef < 1 indicates slower rates [49].

3.5. Effects of temperature on bioavailability

Studies have demonstrated that temperature optimization had a positive effect on biodegradation of hydrophobic organic compounds especially for PAHs in a soil historically contaminated with these hydrocarbons. These findings indicated that in-situ remediation processes are accelerated with elevated temperature in a range between mesophilic and thermophilic temperatures. However, at a high temperature, the activity of fungal and bacterial populations is reduced [50]. Temperatures in the thermophilic range (50 to 60°C) are shown to greatly accelerate decomposition of organic matter, in general [51]. Microbial utilization of hydrocarbons can occur at temperatures ranging from -2 to 70°C. Iqbal et al. [52] investigated the ability of indigenous aerobic microorganisms to degrade low and HMW PAHs in sewage sludge fed in continuous bioreactors. It was reported that when the temperature increased from 35 to 45°C and at 55°C, biodegradation of the high molecular weight PAHs was enhanced from 50 to 80%. The results also showed improved kinetic rates with elevated temperature. A reduction in kinetic rates was associated with a decrease in contaminant concentrations over time; however, the kinetic rates were found to be dependent upon the contaminants desorption and environmental factors than concentration; i.e. significant kinetic rates was observed in the ambient and high temperature biodegradation processes.

Temperature elevation coupled with moisture optimization was also determined to enhance the bioremediation of such contaminated soil. Raising the temperature also decreases adsorption, which makes more organic material available for microorganisms to degrade. With the synergistic effects of elevated temperature and sufficient moisture content, White et al. [53] determined that moisture and slurrying soil containing organic compounds dramatically enhanced bioavailability and the rate of biodegradation. Reports also show that desorption resistant HMW PAHs were more efficiently metabolized in slurried than in unslurried soil suggesting that temperature and moisture optimization needs to be combined with efficient nutrient delivery systems for soils/sediments.

Furthermore, temperature plays a role when nutrients are added for biodegradation. Previous studies indicate that at 10°C, biodegradation rates were not affected by the addition of phosphorus or nitrogen. However, at 20°C, biodegradation was increased by the addition of phosphorus [54]. This suggests that temperature optimization needs to be combined with sufficient and suitable nutrient amendments. Sartoros et al. [55] considered the biodegradation of a mixture of two PAH compounds, pyrene and anthracene, by a developed enrichment culture with the addition of surfactant at a low temperature of 10°C and discovered a negative impact on the biodegradation. It was also observed that the overall extent and the maximum specific rate of PAHs mineralization decreased with the decrease of temperature; the variation of total PAH concentration had negligible effect. However, at 25°C the addition of a surfactant enhanced the mineralization of PAHs. These results have important implications on the use of surfactants for in-situ bioremediation since groundwater temperatures are often at or below 10°C.

In a bioaugmentation system, where allochthonous or genetically engineered microorganisms are added into contaminated soil to aid the operation of indigenous microbes, microbial population can decline rapidly following their introduction into such natural soil, and growth of the engineered populations in microbiologically undisturbed soils is a rare phenomenon due to microbiostasis [56, 57]. Furthermore, temperature variability is one of the principal contributors leading to the decline of microorganisms introduced into a 'hostile' soil microenvironment. In high temperature treatments, the response and survival of the microorganisms will be compromised compared to ambient temperature treatments. The microbial concentration increases under ambient temperature thus significantly increasing remediation activity. Results suggest that the stimulated growth and activity of indigenous microbes with elevated temperature in non-inoculated treatment indicates a positive relationship between optimum temperatures and better biodegradation performance.

4. Enhancing bioavailability of HMW PAHs using biosurfactants from renewable resources

4.1. Effects of biosurfactants on sorbed PAHs

Biosurfactants are surface active agents produced by microorganisms. Table 1 shows some of these microorganisms and the different groups of biosurfactant they produce. All biosurfactants consist of two parts, a polar (hydrophilic) moiety and a non polar (hydrophobic) group. A hydrophilic group consists of mono-, oligo- or polysaccharides, peptides or proteins and a hydrophobic moiety usually contains saturated, unsaturated and hydroxylated fatty acids or fatty alcohols [58]. Due to their amphiphilic structure, biosurfactants show a wide range of properties, including the lowering of surface and interfacial tension of liquids, the ability to form micelles and micro-emulsions between two different phases, the ability to increase the surface area of hydrophobic water-insoluble substances, and thus increase the water bioavailability of such substances. In comparison to their chemically synthesized equivalents they have many advantages; they are environmentally friendly, biodegradable, less toxic and non-hazardous. They have better foaming properties and higher selectivity; they are active at extreme temperatures, pH and salinity, and can be produced from wastes and from various by-products. This feature makes the production of cheap biosurfactants possible and the concomitant effects of utilizing waste substrates and reducing their environmental pollution [59-63]. Biosurfactants increase the bioavailability of PAHs resulting in enhanced growth of the degrading microorganism and the biodegradation of the contaminants.

An important feature of the physico-chemical properties of surfactants is their hydrophilic-lipophilic balance (HLB) [64, 65]. The HLB value indicates whether a surfactant will produce a water-in-oil or oil-in-water emulsion. Emulsifiers with lower HLB values of 3 to 6 are lipophilic and promote water-in-oil emulsification, while emulsifiers with higher HLB values between 10 and 18 are more hydrophilic and promote oil-in-water emulsion formation [5]. A classification based on HLB values has been used to evaluate the suitability of different surfactants for various applications. For example, it has been reported that successful surfactants are those with the ability to promote desorption of contaminants from contaminated soils and are normally those with HLB values above 10 [66].

BiosurfactantMicroorganismApplications in Environmental BiotechnologyReferences
GroupClass
GlycolipidsRhamnolipidsPseudomonas aeruginosa, Pseudomonas spEnhancement of the degradation, dispersion, emulsification of different classes of hydrocarbons and vegetable oils; removal of metals from soil.[69, 71]
TrehalolipidsMycobacterium tuberculosis, Rhodococcus erythropolis, Arthrobacter sp., Nocardia sp., Corynebacterium sp.Enhancement of the bioavailability of hydrocarbons.[72]
SophorolipidsTorulopsis bombicola, Torulopsis petrophilum, Torulopsis apicolaRecovery of hydrocarbons from dregs and muds; removal of heavy metals from sediments; enhancement of oil recovery.[73, 74, 69]
Fatty acids, phospholipids and neutral lipidsCorynomycolic acidCorynebacterium lepusEnhancement of bitumen recovery.[75]
Spiculisporic acidPenicillium spiculisporumRemoval of metal ions from aqueous solution; dispersion action for hydrophilic pigments; preparation of emulsion-type organogels, microencapsulation[76]
Phosphati-dylethanolamineAcinetobacter sp., Rhodococcus erythropolisIncreasing the tolerance of bacteria to heavy metals.[77]
LipopeptidesSurfactinBacillus subtilisEnhancement of the biodegradation of hydrocarbons and chlorinated pesticides; removal of heavy metals from a contaminated soil, sediment and water; increasing the effectiveness of phytoextraction.[78]
LichenysinBacillus licheniformisEnhancement of oil recovery[79]
Polymeric biosurfactantsEmulsanAcinetobacter calcoaceticus RAG-1Stabilization of the hydrocarbon-in-water emulsions.[80]
AlasanAcinetobacter radioresistens KA-53[81]
BiodispersanAcinetobacter calcoaceticus A2Dispersion of limestone in water.[82]
LiposanCandida lipolyticaStabilization of hydrocarbon-in-water emulsions.[83]
MannoproteinSaccharomyces cerevisiae[84]

Table 1.

Biosurfactants producing organisms: classification and application in environmental biotechnology.

Source: Pacwa-Płociniczak et al. [85]


Another feature is the Critical Micelle Concentration (CMC); which is the concentration above which the formation of micelles is thermodynamically favored [67]. The mobilization mechanism occurs at concentrations below the biosurfactant CMC. At such concentrations, biosurfactants reduce the surface and interfacial tension between air-water and soil-water systems. Due to the reduction of the interfacial force, contact of biosurfactants with a soil-oil system increases the contact angle and reduces the capillary force holding the oil and soil together. Above the biosurfactant CMC, the solubilization process takes place. At these concentrations, biosurfactant molecules aggregate to form micelles, which dramatically increase the solubility of the oil. The hydrophobic part of the biosurfactant molecules interconnect inside the micelle while the hydrophilic ends are then exposed to the aqueous phase on the exterior. Consequently, the interior of a micelle creates an environment compatible for hydrophobic organic molecules. The process of incorporation of these molecules into a micelle is known as solubilization [68]. The formation of micelles leads to a significant increase in the apparent solubility of hydrophobic organic compounds, even above their water solubility limit, as these compounds can partition into the central core of a micelle. The effects of such a process are the reduction of surface and interfacial tension, enhancement of mobilization and mass transfer of contaminants from soil particles into the aqueous phase, and consequently the bioavailability of the hydrophobic contaminants for microbial attack [69, 70].

4.2. Biosurfactants production using agricultural and industrial wastes

The bioconversion of waste materials is considered to be of importance for the development of sustainable biotechnology processes in the near future because of its favorable economics, low capital and energy cost, reduction in environmental pollution, and their relative ease of operation [86, 10, 87, 88]. Producing usable products from agricultural and industrial waste is therefore a feasible and favorable option [89, 90]. Modern society produces high quantity of waste materials through activities related to industries such as those in the forestry, agriculture and municipal sectors [86, 91].

The use of the alternative substrates such as agro-based industrial wastes is one of the attractive strategies for the economic production of biosurfactants to enhance biodegradation of environmental hydrophobic contaminants. It has been suggested that successful approaches to more economical production technologies of biosurfactants will be a collaborative approach involving process development and sustainable raw material supplies. According to Marchant and Banat [92], emphasis should be on the cost effective management of downstream processing. These inexpensive agro-industrial wastes substrates include olive oil mill effluent, plant oil extracts and waste, distillery and whey wastes, potato process effluent and cassava wastewater [10]. These waste materials are some examples of food industry by-products or waste that can be used as feedstock for biosurfactants production. Similarly, vegetable oil wastes can be used for biosurfactant production as they are lipidic carbon sources and are mostly comprised of saturated or unsaturated fatty acids with 16 to18 carbon atoms chain.

Studies involving the application of a variety of vegetable oils for biosurfactants production from canola, corn, sunflower, safflower, olive, rapeseed, grape seed, palm, coconut, fish and soybean oil have been reported. The world production of oils and fats is about 2.5 to 3 million tons, 75% of which are derived from plants and oil seeds [93]. The high content of fats, oils and other nutrients in these wastes make them invaluable cheap raw materials for industries involved in useful metabolite production. Furthermore, from an economical point of view, nutrient rich agricultural residues can be employed for producing useful biological products such as biosurfactants. These materials are among the most abundant organic carbon available on earth [94] and they are the major components of different waste streams from various industries.

In recent times, studies have been focused on the application of agro-industrial wastes or by-products for the production of biosurfactants which are used in crude form or the direct use of surfactants producing strains for biodegradation processes. This is due to the high cost of biosurfactant purification and the stability including sustainability provided by these biosurfactants producing strains in biodegradation processes. The production and properties of a biosurfactant, synthesized by Bacillus subtilis LB5a strain, using cassava wastewater as a substrate was investigated. The microorganism was able to grow and to produce a surfactant on cassava waste, reducing the surface tension of the medium to 26.6 mN/m and giving a crude surfactant concentration of 3.0 g/L after 48 h [95]. The biosurfactant obtained was capable of forming stable emulsions with various hydrocarbons. Panesar et al. [96] investigated the suitability of molasses, the sugar industry by-product, for biosurfactant production using Pseudomonas aeruginosa strain ATCC 2297. An attempt was also made to replace the costly nitrogen sources with agro-industrial by-products to formulate low cost medium for biosurfactants production. The strain was found to displayed maximum emulsification activity on molasses medium after 120 h of incubation under optimized conditions. Biosurfactants production by a strain of Pseudomonas aeruginosa using palm oil as a sole carbon source was also investigated [97]. The P. aeruginosa strain gave emulsification index results of 100% when diesel was used as an oil phase and was able to reduce surface tension of three tested inorganic media to approximately 33 mN/m. Wan-Nawawi et al. [98] also reported the versatility of a bacterial strain isolated from a hydrocarbon-based source at a palm oil mill. The strain showed a high bacterial growth on sludge palm oil with a surface tension of 36.2 mN/m and was therefore proposed for biosurfactant production by liquid state fermentation.

4.3. Application of biosurfactants for enhancing PAHs bioavailability

Only limited numbers of microorganisms are capable of degrading HMW PAHs. Hence their biodegradation is limited by their low bioavailability to the microorganisms, which is due to their hydrophobicity, low aqueous solubility and strong adsorptive capacity in soil [99, 100]. Berg et al. [101] described an emulsifying agent produced by P. aeruginosa UG2 that increased the solubility of hexachlorobiphenyl added to soil slurries, resulting in a 31% recovery of the compound in the aqueous phase. Griffin et al. [102] demonstrated that rhamnolipids from bacteria, in combination with the oleophilic fertilizer Inipol EAp-22, increased the degradation rate of hexadecane, benzene, toluene, o- and p-cresol and naphthalene in aqueous-phase bioreactors and in those containing soil. They also reported increased rates of biodegradation of aliphatic and aromatic hydrocarbons by pure bacterial cultures.

The efficiency of biosurfactants in the remediation of soil contaminated by phenanthrene and polychlorinated biphenyls (PCBs) was also reported [103]. In an investigation of the capacity of PAH-utilizing bacteria to produce biosurfactants using naphthalene and phenanthrene, Deziel et al. [104] quantified biosurfactants production that was responsible for an increase in the aqueous concentration of naphthalene. This indicates a potential role for biosurfactants in increasing the solubility of such compounds. Similarly, Zhang et al. [105] determined the effect of two biosurfactants on the dissolution and bioavailability of phenanthrene and reported increases in both solubility and the degradation rate of phenanthrene. Kanga et al. [106] applied glycolipid biosurfactants produced by Rhodococcus sp. H13A and a synthetic surfactant (Tween 80) for enhanced substrate solubility. Using naphthalene and methyl-substituted derivatives in crude oil as representative of the PAH content, they observed that both surfactants lowered surface tension in solutions from 72 to 30 mN/m. The biosurfactants were efficient in increasing the solubility of the hydrocarbons, particularly the substituted derivative. In a laboratory column study, Noordman et al. [107] applied biosurfactants for the enhanced removal of phenanthrene from phenanthrene-contaminated soil, eluting the contaminant with an electrolyte solution containing rhamnolipid. The enhanced removal of phenanthrene occurred mainly by micellar solubilization.

Microbially produced biosurfactants were studied to enhance crude oil desorption and mobilization in model soil column systems [108]. The results showed that the ability of biosurfactants from Rhodococcus ruber to remove the oil from the soil core was 1.4 to 2.3 times greater than that of a synthetic surfactant (Tween 60), of suitable properties. The biosurfactant was less adsorbed to soil components than synthetic surfactant, thus rapidly penetrating through the soil column and effectively removing 65–82% of the crude oil. Chemical analysis showed that the crude oil removed by the biosurfactant contained a lower proportion of high-molecular-weight paraffins and asphaltenes.

The capability of biosurfactants and biosurfactant-producing microorganisms to enhance organic contaminants’ availability and biodegradation rates was reported by several authors [109, 110, 104]. Kang et al. [111] used sophorolipid in studies on biodegradation of aliphatic and aromatic hydrocarbons and Iranian light crude oil under laboratory conditions. The addition of this biosurfactant to soil increased biodegradation of tested hydrocarbons with the rate of degradation ranging from 85% to 97% of the total amount of hydrocarbons. Their results indicated that sophorolipid may have the potential for facilitating the bioremediation of sites contaminated with hydrocarbons having limited water solubility and increasing the viability of microbial consortia for biodegradation. The solubility and utilization of pyrene as a sole carbon source by the biosurfactant-producing bacterial strains; Bacillus subtilis DM-04, Pseudomonas aeruginosa mucoid (M) and nonmucoid (NM), isolated from a petroleum-contaminated soil were studied [112]. It was reported that the biosurfactants produced by the bacteria under the study were capable of enhancing the solubility of pyrene in aqueous media and can influence the cell surface hydrophobicity of the biosurfactant-producing strains that results in a higher uptake of pyrene.

5. Conclusion

Although environmental biotechnology is regarded as an eco-friendly technology for the clean-up of PAH-contaminated ecosystems, the successful application of this technology is still restricted by the enormous costs of its operation and the limited bioavailability of the contaminants to degradative micro-organisms, especially HMW PAHs, due to sorption and sequestration. Many bacteria, fungi and algae and their products have been applied to degrade a range of LMW PAHs, such as naphthalene, fluorene and phenanthrene; however, their activity towards HMW PAHs containing five or more fused benzene rings, such as Benzo(a)pyrene and Benzo(ghi)perylene, is limited. Application of biosurfactants produced using agricultural and industrial wastes may be promising for reducing the costs of biodegradation technology as well as enhancing bioavailability of HMW PAHs. However, there is a dearth of research on this subject. Bioavailability model could be a vital tool to estimate and assess the success of bioremediation; therefore, more research is needed in this area, considering variations in environmental conditions that could limit field simulation of laboratory results. The synergistic effects of increased temperature and moisture with biosurfactants application have been shown to enhance biodegradation efficiency; however, kinetic investigation is important under these conditions to provide an understanding of biodegradation rate in situation where these conditions cannot be controlled such as in a typical field operation.

© 2013 The Author(s). Licensee IntechOpen. This chapter is distributed under the terms of the Creative Commons Attribution 3.0 License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

How to cite and reference

Link to this chapter Copy to clipboard

Cite this chapter Copy to clipboard

Olusola Solomon Amodu, Tunde Victor Ojumu and Seteno Karabo Obed Ntwampe (February 7th 2013). Bioavailability of High Molecular Weight Polycyclic Aromatic Hydrocarbons Using Renewable Resources, Environmental Biotechnology - New Approaches and Prospective Applications, Marian Petre, IntechOpen, DOI: 10.5772/54727. Available from:

chapter statistics

2007total chapter downloads

1Crossref citations

More statistics for editors and authors

Login to your personal dashboard for more detailed statistics on your publications.

Access personal reporting

Related Content

This Book

Next chapter

Polyhydroxyalkanoate (PHA) Production from Carbon Dioxide by Recombinant Cyanobacteria

By Hitoshi Miyasaka, Hiroshi Okuhata, Satoshi Tanaka, Takuo Onizuka and Hideo Akiyama

Related Book

First chapter

Biotechnology of Agricultural Wastes Recycling Through Controlled Cultivation of Mushrooms

By Marian Petre and Alexandru Teodorescu

We are IntechOpen, the world's leading publisher of Open Access books. Built by scientists, for scientists. Our readership spans scientists, professors, researchers, librarians, and students, as well as business professionals. We share our knowledge and peer-reveiwed research papers with libraries, scientific and engineering societies, and also work with corporate R&D departments and government entities.

More About Us