Abstract
In the last few years, the combination of laser irradiation with atmospheric pressure plasmas, also referred to as laser–plasma hybrid technology, turned out to be a powerful technique for different materials processing tasks. This chapter gives an overview on this novel approach. Two methods, simultaneous and sequential laser-plasma processing, are covered. In the first case, both the plasma and the laser irradiation are applied to the substrate at the same time. Depending on the process gas and the discharge type, the plasma provides a number of species that can contribute to the laser process plasma-physically or plasma-chemically. Sequential plasma-enhanced laser processing is based on a plasma-induced modification of essential material properties, thus improving the coupling of laser energy into the material during subsequent laser ablation. Simultaneous plasma-assisted laser processing allows increasing the efficiency of a number of different laser applications such as cleaning, microstructuring, or annealing processes. Sequential plasma-assisted laser processing is a powerful method for the processing of transparent media due to a reduction in the laser ablation threshold and an increase in the ablation rate at the same time. In this chapter, the possibilities, underlying mechanisms, performance, and limits of the introduced approaches are presented in detail.
Keywords
- Laser-plasma-hybrid techniques
- atmospheric pressure plasma
- cleaning
- microstructuring
- modification
1. Introduction
During the last decades, both lasers and plasmas have become essential integral parts of modern manufacturing technology and surface engineering. The coupling of laser irradiation and plasmas, which can be realized either at low or atmospheric pressure, has turned out to be a powerful combination for a number of different applications. For example, plasma-assisted pulsed laser deposition (PLD), which is performed in vacuum environment, allows the generation of special functional thin films [1,2]. In this context, laser–plasma coupling also offers the possibility of increasing the total efficiency of PLD processes by a reduction of the laser ablation threshold of some target materials such as tungsten due to the plasma perforation of the target surface and a subsequent laser-induced bursting of gas-filled pores [3].
Plasma-enhanced laser materials processing at atmospheric pressure is most commonly known from welding technology. Here, the laser-induced plasma results in the formation of a so-called keyhole, which allows an improved stirring of the molten material as well as a significant increase in welding depth and thus a larger and more homogenous welding seam [4,5]. In this context, laser irradiation can also be added to plasma arc welding processes in order to improve the process performances [6,7]. The plasmas used for this purpose are usually high-energetic arc discharges, driven at several amperes, where the metallic work piece itself acts as counter electrode. However, these techniques are not suitable for the machining of temperature-sensitive materials or for obtaining marginal and locally well-defined material removal as required in the case of cleaning or microstructuring.
For the latter task, the so-called laser-induced plasma-assisted ablation (LIPAA) method represents a promising approach for plasma-enhanced laser materials processing. LIPAA was developed in order to overcome the limits during laser ablation of glasses which are given by the high transparency of such media. Here, a focused laser beam is guided through the glass work piece onto a metallic target which is placed close to the rear side of the glass. As a result, a laser-induced plasma is ignited within the gap between the work piece and the target. Ablation of the transparent glass is then obtained due to a successive deposition of an absorbing metallic layer on its surface and a charge exchange amongst ions and electrons as well as a transfer of kinetic or potential energy, provided by radicals and ions [8,9].
In the last years, the simultaneous or sequential combination of low-energetic atmospheric pressure plasmas, mainly based on dielectric barrier discharges (DBD) and thus featuring low gas temperatures, and laser irradiation has turned out to be a powerful tool for a number of different applications. Such combination is also referred to as laser–plasma hybrid technology and represents another approach for improving laser-based materials processing techniques such as modification, cleaning, drilling, and cutting as well as structuring. In this context, auxiliary plasmas allow to increase the total process and energy efficiency and to improve the machining quality as presented in more detail in this chapter.
2. Laser–plasma coupling
The aim of plasma-enhanced laser materials processing is to benefit from interactions and synergies arising from the particular phenomena provided by laser irradiation and plasmas in order to improve the machining efficiency and quality of different processes. As shown in Figure 1, this technology is based on either simultaneous or subsequent coupling of both energy sources and the resulting impact on any work piece surface.
Especially in the case of simultaneous processing, this approach results in a complex matrix laser-plasma-substrate. Thus, a proper inline process monitoring, for example, laser-induced breakdown spectroscopy (LIBS) or Rayleigh scattering analysis becomes crucial for a description and control of the process. This is of significant importance due to the number of different interacting parameters and mechanisms provided by laser irradiation and plasmas, which are introduced in more detail in the following sections.
2.1. Laser–matter interactions
Only three years after the presentation of the first operable laser source, its suitability for materials processing applications was demonstrated by the fabrication of diaphragms with an inner diameter of some microns [10]. Since that time, the laser has established as a state-of-the-art technology in different fields of materials processing and mainly material removal, commonly referred to as laser ablation. However, laser materials processing involves a number of different mechanisms such as photochemical, optical, and/or thermal processes, namely, ablation, desorption, or melting. Here, the particular process is set by the applied laser parameters.
The main influencing parameter during laser ablation is the wavelength-dependent absorption coefficient
with
It can easily be seen that surface absorption results from high absorption coefficients, whereas bulk absorption occurs in the case of low absorption coefficients. This fact is crucial for the choice of the laser wavelength for machining a given material with specific optical properties.
Another essential parameter for materials processing is the laser pulse duration
the latter results from both thermodynamic material characteristics, expressed by the thermal conductivity
The laser wavelength and its pulse duration further determine the laser fluence
To summarize, a number of different laser parameters have to be controlled in order to realize an optimized and high-quality machining process, depending on specific optical and thermodynamic characteristics of the work piece material. These laser parameters are wavelength, pulse duration, energy, and fluence as well as the repetition rate. In terms of plasma-enhanced laser materials processing, plasma–matter interactions have to be considered additionally.
2.2. Plasma–matter interactions
Similar to lasers, plasma sources have been used in manufacturing for several decades now, for example, for plasma cutting, arc welding, surface activation, or EUV lithography. This wide range of clearly different applications can be addressed, thanks to the versatility of technical plasmas. Plasma effects are generally influenced by the particularly applied operating parameters such as the high-voltage
Within a plasma volume, both neutral and charging electron collision-induced gas phase processes such as dissociation, excitation, ionization, and attachment can take place as visualized in Figure 2.
In terms of materials processing, plasmas thus potentially allow the following:
The chemical reduction or oxidation of the work piece surface or adherents by chemically active plasma species (applicable for both direct and indirect discharges)
An energy transfer to the work piece surface resulting from the de-excitation of metastable plasma species at walls (applicable for both direct and indirect discharges)
A certain plasma heating of the work piece surface (applicable for both direct and indirect discharges)
An acceleration of charge carriers due to a high electrical field strength in the sheath region on the work piece surface (applicable for direct discharges)
The formation of UV radiation (applicable for direct discharges where UV radiation is generated close to the surface)
As listed above, some of these phenomena especially become of importance in direct plasma discharges where the work piece itself represents a component of the discharge geometry. The choice of the discharge type thus plays an essential role for any plasma-based materials processing application.
Plasma treatment is a state-of-the-art method for surface activation, mainly for improving the adhesion of lacquers or glues on synthetic materials by the formation of polar groups on the substrate surface [13,14]. Another established field of application is plasma sterilization [15] or plasma cleaning [16,17]. For the latter application, hydrocarbons (
However, an excitation of a carbon atom can also be achieved by collisions with electrons within the plasma as shown in Figure 3.
The carbon–hydrogen (C-H) bond features an original binding energy of approximately 4.4eV. Relating to laser irradiation, this energy corresponds to a laser wavelength of approximately 282 nm. Once a carbon atom within this bond is excited by such a collision, the energy required for breaking this bond is <4.4eV. The excitation of atoms by plasma thus offers new possibilities for laser processes and especially allows the use of energy- and cost-efficient standard laser sources. In the example given above, a 3rd-harmonic Nd:YAG laser instead of a 4th-harmonic one could be used for material removal, consequently improving the total energy efficiency of such a laser-based process.
Due to the possibility of generating reactive species, plasmas are further suitable for surface etching [18]. For instance, silicon-based materials such as silicon dioxide (SiO2) can be processed using fluorochemical compounds as process gas. According to
etching is achieved by chemical reactions of both fluorine (F) provided by the plasma and silicon dioxide. As a result, gaseous silicon tetrafluoride (SiF4) and gaseous dioxygen (O2) are formed. Such plasma etching is also referred to as reactive atomic plasma technology (RAPT®).
3. Plasma-enhanced laser processes
3.1. Simultaneous laser–plasma processing
For simultaneous laser–plasma processing, suitable plasma and laser irradiation are applied to the work piece at the same time in order to generate synergetic effects between both sources of energy. Since plasma-induced chemical reactions require a certain length of time that is typically much longer than the temporal distance between the single pulses of pulsed laser irradiation (e.g., 100 µs for a laser pulse repetition rate of 1 kHz), this approach is rather based on the utilization of plasma-physical effects as also listed in the inlet in Figure 1. Here, the plasma discharge type plays a key role since some of these effects are only existent in either direct discharges or remote plasmas. In addition, plasma-chemical effects such as a constant chemical reduction or oxidation can contribute to the process as for example, in the case of laser–plasma cleaning.
3.1.1. Laser–plasma cleaning
Plasma-enhanced laser processing is suitable for cleaning contaminated and oxidized or corroded surfaces and can also be applied for the removal of coatings or lacquers. In the first case, the actual laser cleaning process, based on desorption or ablation of surface-adherent contaminants, is supported by a modification of such contaminants by suitable plasmas. Depending on the chemical composition of the contaminants, either chemically reducing or oxidizing plasmas are applied. As an example, the reduction of surface-adherent oxides is achieved by the use of nitrogenous or hydrogenous process gases, whereas oxygen plays a key role for the removal of carbon-based layers (compare Eq. 5). Employing both laser and plasma cleaning at the same time allows a significant increase in cleaning efficiency as exemplified in Figure 4.
Here, laser–plasma cleaning of corroded coins was performed by introducing a plasma jet to Nd:YAG laser irradiation with a wavelength of 1064 nm. The plasma process gas was a mixture of argon (95%, carrier gas) and hydrogen (5%), leading to the formation of hydrogen radicals within the plasma [19,20]. Even though a pure plasma treatment features only a marginal cleaning efficiency, the combination of both laser-induced cleaning and plasma-induced reduction is a powerful tool for this task. In addition to an improvement of the cleaning efficiency, this hybrid approach also allows to reduce the laser fluence required for the cleaning process. In the present case shown in Figure 4, the laser fluence for cleaning was 0.6 J/cm² without any plasma and 0.4 J/cm² when applying the plasma simultaneously [19]. Thus, the required laser fluence is reduced by a factor of 1.5, which notably contributes to the overall energy efficiency of such hybrid cleaning processes.
As shown by Eq. 5 and illustrated in more detail in Figure 3, both plasma-chemical and plasma-physical processes can furthermore contribute to the laser removal of carbon-based coating materials such as parylene [21] by the excitation of carbon bonds or the oxidation of hydrocarbons. For this purpose, air can be used as process gas. Based on these effects, laser–plasma cleaning is thus a suitable technique for an efficient removal of graffiti sprays, spray lacquers, acryl paints, and acrylic and alkyd resins [22]. Since laser-based processes can be performed localized with a high accuracy, laser–plasma cleaning is thus of interest for the selective removal of protecting layers, e.g., for electrical contacting, the large-scale removal of bleached and aged lacquers, the restoration of artworks, etc.
3.1.2. Laser–plasma annealing
For the production of thin film transistor (TFT)-based flat screen displays, excimer laser annealing (ELA) represents an established method. Here, large-scale crystallization of amorphous silicon layers on glass substrates is performed by specifically shaped, i.e., laterally homogenously distributed laser beams [23]. The efficiency of this technique is currently limited by the laser energy of available sources. In order to overcome this restriction and to machine a large surface area, several excimer laser sources are coupled in order to achieve energy densities sufficient for large-scale annealing. In this context, adding appropriate plasma sources to the ELA process allows an increase in the process efficiency. Such increase can be achieved by simple plasma-induced heating of the silicon layer, which directly impacts the temperature-dependent bad gap
Here,
Another approach is to add cold, physically active plasmas to an ELA process. For example, direct DBD argon plasmas turned out to be suitable for increasing the crystallization efficiency by a factor of maximum 1.9 [25] as exemplified in Figure 5.
Even though the underlying mechanisms of this approach are not yet fully understood, the increase in crystallization efficiency is most likely due to a plasma-induced additional energy transfer by inelastic collisions of excited argon atoms and metastable argon species at the silicon layer surface as described in more detail in Section 3.1.4. Further, the formation of dipoles within the amorphous silicon layer due to the used direct discharge and the accompanying change in optical properties can contribute to an improved coupling of incoming laser energy into the layer. Even though laser–plasma annealing allows a significant enhancement of an ELA process in terms of its efficiency, it is subject to the restriction that the silicon-coated substrate necessarily has to be brought into a direct DBD plasma. The application of this method on an industrial scale, where typically laser line foci with a width of 1 to 1.5 m are used for ELA, is thus a challenging task to be solved in the future.
3.1.3. Laser–plasma engraving
Laser engraving is applied for the realization of microstructures for micromechanical devices and actuators or for marking print rolls. Here, the most disturbing effect is the formation of burrs and debris, i.e., resolidified material and condensed material vapor close to the ablation area. Typically, such burrs and debris droplets are of the same size as the actual laser-engraved structure and consequently limit the performance of any microstructured functional device. The use of assisting plasmas during laser engraving allows a reduction of these effects. As confirmed by X-ray photoelectron spectroscopic analysis of laser-induced debris on stainless steel, it is chemically reduced when applying appropriate plasma process gases. As a result, the debris features notably lower content of oxygen [26]. The additional (thermal) energy provided by the plasma further gives rise to a higher degree of vaporization of the laser-induced plume and thus inhibits the recondensation of material on the surface as shown by the comparison in Figure 6.
In principle, the formation of debris during laser engraving of different metals and alloys can be reduced by assisting plasmas [26]. However, this effect is strongly dependent on the particular chemical composition of the work piece and the plasma process gas mixture.
3.1.4. Laser–plasma drilling and cutting
Simultaneous plasma-enhanced laser processing can be applied for increasing the ablation rate during laser machining of various materials. As a consequence, the efficiency of laser drilling and cutting can be improved. For this purpose, a direct DBD-based argon plasma beam can be introduced to a focused laser beam, where both the plasma beam and the laser beam are guided coaxially as presented in more detail in [25,27–29]. As shown in Figure 7, this configuration allows increasing the ablation depth during laser drilling of optical glasses by a factor of approximately 2 in comparison to pure laser drilling without any assisting plasma [27].
It can also be applied to metals, where the maximum increase in volume ablation rate was even reported to be by a factor of 9.6 in the case of aluminum [28]. Principally, an increase in ablation rate was also achieved for aluminum oxide [29]. As observed by laser-induced breakdown spectroscopic measurements during both pure laser ablation and simultaneous plasma-assisted laser ablation of aluminum oxide, applying plasma additionally results in an intensification of characteristic spectral lines of aluminum ions (AlII) as shown in Figure 8.
Further, more spectral lines of neutral aluminum (AlI) and aluminum ions (AlII and AlIII) appear. This confirms the increase in material removal by a plasma-induced high-energetic process with respect to pure laser machining. However, this increase cannot be explained by a simple addition of the particular energies of the laser and the plasma. It is rather a synergetic effect, which can be described as follows: In the course of the laser evaporation process, the particles within the arising laser plume feature a considerably large surface for collision processes. Such collision results in a de-excitation of excited plasma species [30] and thus comes along with the disposal of energy, which amounts to 11.55 eV for the 3P2 argon metastable (Arm) state and 11.72 eV for the 3P0 Arm state, respectively. The formation of an ablation plume by the laser is thus of significant importance for energetic laser–plasma synergies that arise from this mechanism.
Since in the above-described setup, the work piece is placed within the discharge gap, the coupling of incoming laser energy can furthermore be supported by local-transient substance changes as, for example, a formation of dipoles and the accompanying modification of near-surface optical properties. Another—although marginal—effect during simultaneous plasma-enhanced laser machining is the influence of the plasma beam on the propagation characteristics of the laser beam. Here, the plasma acts as thermal gradient index lens, thus resulting in a certain focus shift of the passing focused laser beam. However, due to the relatively low gas temperature of DBD plasmas, this focus shift of 2 to 4 mm [31] is usually much lower than the Rayleigh length
For instance,
3.2. Sequential laser–plasma processing
Sequential laser–plasma processing represents a powerful tool for enhancing the laser machining quality and efficiency of transparent media such as glasses. This method is a combination of plasma pretreatment and subsequent laser ablation. Using hydrogenous process gases for plasma pretreatment, the energy coupling of incoming laser irradiation can be significantly improved due to a modification of the optical properties of the work piece. First, the process gas is dissociated as a result of collisions with electrons within the plasma volume. The atomic hydrogen generated in this vein can then induce several reactions at the surface of the work piece. In the case of glasses, the main mechanisms are the chemical reduction of glass network-forming oxides such as silicon dioxide (SiO2) according to
resulting in the formation of a substoichiometric mixed phase at the surface, and the implantation of hydrogen into deeper regions of the glass bulk material. The substoichiometric mixed phase can be referred to as silicon suboxide (SiOx, where 1 <
One has to notice that this increase in absorption is a reversible process. The initial transmission characteristics can nearly be reobtained by tempering the plasma-treated glass and thus removing the implanted hydrogen and reoxidizing the glass network [35].
In terms of laser ablation subsequent to the plasma pretreatment, the increase in absorption allows a notable reduction of the laser ablation threshold up to a factor of 4.6 when using an argon-fluoride excimer laser with an emission wavelength of 193 nm [36]. Due to the accompanying decrease in energy deposition into the glass, a higher contour accuracy and lower roughness of the ablated area is achieved as exemplified in Figure 10.
Thus, the sequential laser–plasma processing of glasses allows both a saving of laser energy and an improvement of the machining quality at the same time [37]. The implanted hydrogen further acts as reaction partner for oxygen within the SiO2 network during multiple pulse laser ablation. This results in the formation of a new substoichiometric layer at the bottom of the ablated area as confirmed by secondary ion mass spectroscopic investigations. As a result of this laser–plasma-induced effect, the absorption for each following laser pulse and consequently the depth ablation rate is constantly increased with respect to pure laser ablation as shown in Figure 11 [38].
In addition to a decrease in ablation threshold, an increase in ablation rate and an improvement of the contour accuracy the above-described plasma treatment allows the use of energy-efficient laser sources. Due to the plasma-induced increase in UV absorption, 4th-harmonic Nd:YAG lasers instead of excimer lasers can be applied for machining fused silica [39]. Even though the highest efficiency of the plasma pretreatment is found in the case of fused silica as substrate material, this approach can also be successfully applied to optical glasses [40] or technical glasses such as photovoltaic cover glasses [41]. However, due to the significantly denser network of multi-component glasses, the implantation of hydrogen and the formation of the above-described related mechanisms that come along with the presence of hydrogen are limited.
The above-described plasma pretreatment strongly influences the surface polarizability
where
4. Summary
The combination of both atmospheric pressure plasmas and laser irradiation allows increasing the total process efficiency and machining quality of a number of laser-based processes such as cleaning, modification and material removal. For this purpose, either plasma-chemical or plasma-physical effects or mechanisms can be employed. Chemical plasma effects involve the reduction, oxidation, or excitation of bonds, which contribute to laser-induced removal of pollutants or layers. Plasma-physical effects such as collision-induced de-excitation of metastables and high electric field strengths at work piece surfaces can be used in order to improve the modification of coatings and to increase the laser ablation rate. Due to the multiplicity of laser and plasma parameters, the partial complexity of the underlying mechanisms and interactions and the wide range of different materials, plasma-enhanced laser materials processing is still at an early stage. However, the suitability of this approach for a number of different applications was shown over the last years as presented in this chapter. In order to implement this technique in an industrial scale where focused laser beams are usually scanned for large-scale treatment, appropriate and adapted plasma sources should be developed. Due to the principle of DBD plasma sources, such upscaling can be realized quite easily. To summarize, it can be stated that the coupling of laser irradiation and atmospheric pressure plasmas facilitates the valorization of a variety of laser processes based on cost- and energy-efficient nanosecond laser sources.
5. Nomenclature
αm: molecule polarizability
α(λ): wavelength-dependent absorption coefficient
ε0: vacuum permittivity
λ: wavelength
ρ: density
τ: laser pulse duration
Φ: laser fluence
Acknowledgments
The authors would like to thank all their coworkers who contributed to the findings and results presented in this chapter, namely, S. Brückner, M. Dammann, A. Gredner, J. Heine, J. Hoffmeister, J. Ihlemann, M. Kretschmer, V. Le Meur, A. Luca, N. Mainusch, F. Peters, S. Rösner, S. Roux, A. Schmiedel, C. Schmiedel, K. Schmidt, D. Tasche, and T. Weihs. The works leading to the presented results were supported by the European Regional Development Funds and the Workgroup Innovative Projects of Lower Saxony in the frame of the “Lower Saxony Innovation Network for Plasma Technology” and the research project “Plasma Cleaning of Wall Painting and Architecture Surfaces.” The authors further thank the German Federal Ministry of Economics and Technology for funding in the frame of the research project “PROKLAMO” as well as the German Federal Ministry of Education and Research for the sponsorship in the frame of the research project “SiPlaH.” The support by the Volkswagen Foundation and the Federal State Lower Saxony by the sponsorship of the research professorship for laser–plasma hybrid technology at the University of Applied Sciences and Arts in the frame of the state funding program Niedersächsisches Vorab is additionally gratefully acknowledged.
References
- 1.
Marozau I., Shkabko A., Dinescu G., Döbeli M., Lippert T. Logvinovich D. et al.. RF-plasma assisted pulsed laser deposition of nitrogen-doped SrTiO3 thin films. Applied Physics A. 2008;93:721–727. DOI: 10.1007/s00339-008-4702-0 - 2.
Pak S. W., Suh J., Lee D. U., Kim E. K.. Growth of ZnTe:O thin films by oxygen–plasma-assisted pulsed laser deposition. Japanese Journal of Applied Physics. 2011;51(1s):01AD04. DOI: 10.1143/JJAP.51.01AD04 - 3.
Kajita S., Ohno N., Takamura S., Sakaguchi W., Nishijima D.. Plasma-assisted laser ablation of tungsten: reduction in ablation power threshold due to bursting of holes/bubbles. Applied Physics Letters. 2007;91:261501. DOI: 10.1063/1.2824873 - 4.
Arata Y., Abe N., Oda T.. Fundamental phenomena in high power CO2 laser welding. Transactions of JWRI. 1985;14(1):5–11. - 5.
Bagger C., Olsen F. O.. Review of laser hybrid welding. Journal of Laser Applications. 2005;17(1):2–14. DOI: 10.2351/1.1848532 - 6.
Mahrle A., Schnick M., Rose S., Demuth C., Beyer E., Füssel U.. Process characteristics of fibre-laser-assisted plasma arc welding. Journal of Physics D. 2011;44:345502. DOI: 10.1088/0022-3727/44/34/345502 - 7.
Mahrle A., Rose S., Schnick M., Beyer E., Füssel U.. Laser-assisted plasma arc welding of stainless steel. Journal of Laser Applications. 2013;25(3):032006. DOI: 10.2351/1.4798338 - 8.
Zhang J., Sugioka K., Midorikawa K.. Laser-induced plasma-assisted ablation of fused quartz using the fourth harmonic of a Nd+:YAG laser. Applied Physics A. 1998;67(5):545–549. DOI: 10.1007/s003390050819 - 9.
Hanada Y., Sugioka K., Obata K., Garnov S. V., Miyamoto I, Midorikawa K.. Transient electron excitation in laser-induced plasma-assisted ablation of transparent materials. Journal of Applied Physics. 2006;99:043301. DOI: 10.1063/1.2171769 - 10.
Norton J. F., McMullen J. G.. Laser‐formed apertures for electron beam instruments. Journal of Applied Physics. 1963;34:3640–3641. DOI: 10.1063/1.1729284 - 11.
Matthias E., Reichling M., Siegel J., Käding O. W., Petzoldt S., Skurk H. et al.. The influence of thermal diffusion on laser ablation of metal films. Applied Physics A. 1994;58(2):129–136. DOI: 10.1007/BF00332169 - 12.
Siegel J., Matthias E., Ettrich K., Welsch E.. UV-laser ablation of ductile and brittle metal films. Applied Physics A. 1997;64(2):213–218. DOI: 10.1007/s003390050468 - 13.
Bellmann M., Gerhard C., Haese C., Wieneke S., Viöl, W.. DBD plasma improved spot repair of automotive polymer surfaces. Surface Engineering. 2012;28(10):754–758. DOI: 10.1179/1743294412Y.0000000059 - 14.
Heine J., Damm R., Gerhard C., Wieneke S., Viöl W.. Surface activation of plane and curved automotive polymer surfaces by using a fittable multi-pin DBD plasma source. Plasma Science and Technology. 2014;16(6):593–597. DOI: 10.1088/1009-0630/16/6/10 - 15.
Cheruthazhekatt S., Černák M., Slavíček P., Havel J.. Gas plasmas and plasma modified materials in medicine. Journal of Applied Biomedicine. 2010;8(2):55–66. DOI: 10.2478/v10136-009-0013-9 - 16.
Shun’ko E. V., Belkin V. S.. Cleaning properties of atomic oxygen excited to metastable state 2s22p4(1S0). Journal of Applied Physics. 2007;102(8):083304. DOI: 10.1063/1.2794857 - 17.
Hansen R. W. C., Bissen M., Wallace D., Wolske J., Miller T.. Ultraviolet/ozone cleaning of carbon-contaminated optics. Applied Optics. 1993;32(22):4114–4116. DOI: 10.1364/AO.32.004114 - 18.
Jeong J. Y., Babayan S. E., Tu V. J., Park J., Henins I., Hicks R. F. et al.. Etching materials with an atmospheric-pressure plasma jet. Plasma Sources Science and Technology. 1998;7(3):282–285. DOI: 10.1088/0963-0252/7/3/005 - 19.
Pflugfelder C., Mainusch N., Ihlemann J., Viöl W.. Removal of unwanted material from surfaces of artistic value by means of Nd:YAG laser in combination with cold atmospheric-pressure plasma. In: Castillejo M., Moreno P., Oujja M., Radvan R., Ruiz J., editors. Lasers in the Conservation of Artworks; 17–21 September 2007; Madrid, Spain. Boca Raton: CRC Press Taylor Francis Group; 2008. p. 55–58. - 20.
Pflugfelder C., Mainusch N., Hammer I., Viöl W.. Cleaning of wall paintings and architectural surfaces by plasma. Plasma Processes and Polymers. 2007;4(S1):S516-S521. DOI: 10.1002/ppap.200731218 - 21.
Schmiedel C., Schmiedel A., Viöl W.. Combined plasma laser removal of parylene coatings. In: Proceedings of the 19th International Symposium on Plasma Chemistry (IPCS19); 27–31 July 2009; Bochum, Germany. International Plasma Chemistry Society; 2009. p. 239–243. - 22.
Mainusch N., Pflugfelder C., Ihlemann J., Viöl W.. Plasma jet coupled with Nd:YAG laser: new approach to surface cleaning. Plasma Processes and Polymers. 2007;4(S1):S33-S38. DOI: 10.1002/ppap.200730302 - 23.
Sameshima T., Usui S., Sekiya M.. XeCl excimer laser annealing used in the fabrication of poly-Si TFTs. IEEE Electron Device Letters. 1986;7(5):276–278. DOI: 10.1109/EDL.1986.26372 - 24.
Varshni Y.P.. Temperature dependence of the energy gap in semiconductors. Physica. 1967;34:149–154. DOI: 10.1016/0031-8914(67)90062-6 - 25.
Gredner A., Gerhard C., Wieneke S., Schmidt K., Viöl W.. Increase in generation of poly-crystalline silicon by atmospheric pressure plasma-assisted excimer laser annealing. Journal of Materials Science and Engineering B. 2013;3(6):346–351. - 26.
Le Meur V., Loewenthal L., Gerhard C., Viöl W.. On the debris formation during atmospheric pressure plasma-assisted laser engraving of stainless steel. In: Gerhard C., Wieneke S., Viöl W., editors. Laser Ablation: Fundamentals, Methods and Applications. 1st ed. New York: Nova Science Publishers; 2015. p. 165–177. - 27.
Gerhard C., Roux S., Brückner S., Wieneke S., Viöl W.. Low-temperature atmospheric pressure argon plasma treatment and hybrid laser–plasma ablation of barite crown and heavy flint glass. Applied Optics. 2012;51(17):3847–3852. DOI: 10.1364/AO.51.003847 - 28.
Gerhard C., Roux S., Brückner S., Wieneke S., Viöl W.. Atmospheric pressure argon plasma-assisted enhancement of laser ablation of aluminum. Applied Physics A. 2012;108(1):107–112. DOI: 10.1007/s00339-012-6942-2 - 29.
Gerhard C., Roux S., Peters F., Brückner S., Wieneke S., Viöl W.. Hybrid laser ablation of Al2O3 applying simultaneous argon plasma treatment at atmospheric pressure. Journal of Ceramic Science and Technology. 2013;4(1):19–24. DOI: 10.4416/JCST2012-00034a - 30.
Bogaerts A., Gijbels R.. Comparison of argon and neon as discharge gases in a direct-current glow discharge a mathematical simulation. Spectrochimica Acta Part B. 1997;52(5):553–565. DOI: 10.1016/S0584-8547(96)01658-8 - 31.
Hoffmeister J., Brückner S., Gerhard C., Wieneke S., Viöl W.. Impact of the thermal lens effect in atmospheric pressure DBD-plasma columns on coaxially guided laser beams. Plasma Sources Science and Technology. 14;23:064008. DOI: 10.1088/0963-0252/23/6/064008 - 32.
Gerhard C., Tasche D., Brückner S., Wieneke S., Viöl W.. Near-surface modification of optical properties of fused silica by low-temperature hydrogenous atmospheric pressure plasma. Optics Letters. 2012;37(4):566–568. DOI: 10.1364/OL.37.000566 - 33.
Skuja L.. Optically active oxygen-deficiency-related centers in amorphous silicon dioxide. Journal of Non-Crystalline Solids. 1998;239(1–3):16–48. DOI: 10.1016/S0022-3093(98)00720-0 - 34.
Gerhard C., Weihs T., Tasche D., Brückner S., Wieneke S. Viöl W.. Atmospheric pressure plasma treatment of fused silica, related surface and near-surface effects and applications. Plasma Chemistry and Plasma Processing. 2013;33(5):895–905. DOI: 10.1007/s11090-013-9471-7 - 35.
Hoffmeister J., Gerhard C., Brückner S., Ihlemann J., Wieneke S., Viöl W.. Laser micro-structuring of fused silica subsequent to plasma-induced silicon suboxide generation and hydrogen implantation. In: Schmidt M., Vollertsen F., Geiger M., editors. Laser Assisted Net Shape Engineering 7 (LANE 2012); 12–15 November 2012; Fürth, Germany. Elsevier; 2012. p. 613–620. DOI: 10.1016/j.phpro.2012.10.080 - 36.
Brückner S., Hoffmeister J., Ihlemann J., Gerhard C., Wieneke S., Viöl W.. Hybrid laser–plasma micro-structuring of fused silica based on surface reduction by a low-temperature atmospheric pressure plasma. Journal of Laser Micro/Nanoengineering. 2012;7(1):73–76. DOI: 10.2961/jlmn.2012.01.0014 - 37.
Gerhard C., Brückner S., Wieneke S., Viöl W.. Atmospheric pressure plasma-enhanced laser ablation of glasses. In: Gerhard C., Wieneke S., Viöl W., editors. Laser Ablation: Fundamentals, Methods and Applications. 1st ed. New York: Nova Science Publisher; 2015. p. 151–163. - 38.
Tasche D., Gerhard C., Ihlemann J., Wieneke S., Viöl W.. The impact of O/Si ratio and hydrogen content on ArF excimer laser ablation of fused silica. Journal of the European Optical Society—Rapid Publications. 2014;9:14026. DOI: 10.2971/jeos.2014.14026 - 39.
Gerhard C., Kretschmer M., Viöl W.. Plasma meets glass—Plasma-based modification and ablation of optical glasses. Optik & Photonik. 2012;7(4):35–38. DOI: 10.1002/opph.201290098 - 40.
Gerhard C., Heine J., Brückner S., Wieneke S., Viöl W.. A hybrid laser–plasma ablation method for improved nanosecond laser machining of heavy flint glass. Lasers in Engineering. 2013;24(5–6):391–403. - 41.
Gerhard C., Dammann M., Wieneke S., Viöl W.. Sequential atmospheric pressure plasma-assisted laser ablation of photovoltaic cover glass for improved contour accuracy. Micromachines. 2014;5(3):408–419. DOI: 10.3390/mi5030408 - 42.
Bach H., Krause D.. Analysis of the composition and structure of glass and glass ceramics. 1st ed. Berlin Heidelberg: Springer Verlag; 1999. 528 p. DOI: 10.1007/978-3-662-03746-1