1. Introduction
A
A ferroelectric transition is usually associated with the condensation of a soft (or low-frequency) mode of lattice motion at the Brillouin-zone centre. Structural transitions triggered by zone-centre soft modes are generally termed ferrodistortive, and in this sense ferroelectrics constitute a subgroup of the class of ferrodistortive transitions. This subgroup involves the condensation of a polar or optically active mode whose condensation causes the appearance of a long rage polar order. If the transition is strongly first order then mode softening may not occur to a significant degree, and in this situation, there is also a possibility that the large polarization which sets in discontinuously at T
Although most ferroelectrics are ferrodistortive (common examples being barium titanate, sodium nitrite, and triglycine sulphate) some are not. To understand this it is necessary to recognize that, because of the existence of coupling between modes, it is not a necessary condition for ferroelectricity that a zone centre polar mode should be driving the instability. Sometimes a driving antidistortive mode can couple directly or indirectly to a zone centre polar mode and upon condensation induce a small spontaneous polarization in an indirect fashion. In this case the primary order parameter is antidistortive in character while the spontaneous polarization is said to be a secondary order parameter of the transition. There can of course be only one primary order parameter (at least for a continuous or near continuous transition), but there may be many induced or secondary order parameters resulting from couplings to the primary order parameter. All the known antiferroelectrics (examples: lead zirconate, ammonium dihydrogen phosphate etc.) are intrinsically antidistortive, although one can conceive of a ferrodistortive antiferroelectric as one having an antiparallel arrangement of electric dipoles occurring within a primitive cell of the higher-symmetry phase. Such a phase is characterized by the condensation of an antipolar zone-centre soft mode.
Once the importance of coupling between polar modes and other modes has been recognized it is clear that, via the piezoelectric interaction (or coupling to acoustic modes), a spontaneous strain will be virtually a universal characteristic of ferroelectrics since all ferroelectrics are piezoelectric. If this strain can be switched by application of stress then an obvious parallel in elastic terms exists with ferroelectricity. This property is termed ferroelasticity, and a crystal is said to be ferroelastic when it has two or more orientation states in the absence of mechanical stress (and electric field) and can be shifted from one to another of these states by mechanical stress. Intrinsic ferroelastic transitions are associated with the condensation of long-wavelength acoustic phonons and many are known.
The optical and acoustic phonon modes involved in ferroelectric and ferroelastic phase transitions can be probed with Brillouin light scattering and ultrasonic techniques. When phonon modes soften, the involved elastic constants undergo anomalous variations which get reflected in ultrasound velocity and attenuation. Elaborate reviews on these subjects have appeared in literature (Luthi & Rehwald, 1980; Cummins, 1990). Other popular techniques used to probe modes in ferroelectrics are dielectric spectroscopy (Grigas, 1996) and neutron scattering (Dorner, 1981). A number of books and reviews on these subjects have appeared in literature (Lines & Glass, 1977). Though technique like measurement of thermal conductivity across phase transition can reveal information about the coupling between ferroelectric soft modes and thermal phonons, not many measurements have appeared in literature on this. The few measurements that have appeared in literature have used the well established steady-state methods of measuring thermal conductivity (Dettmer et al., 1989).
There are several ferroelectrics that undergo successive phase transitions with incommensurate phases (I-phase) from a symmetrical paraelectric to an incommensurate phase at Ti and then from the incommensurate phase to a commensurate polar phase at T
where C,
2. Overview of thermal properties across ferroelectric phase transitions
In the few measurements of the variations of thermal conductivity near ferroelectric phase transitions reported in literature, steady state methods have been employed. One of the first measurements was on BaTiO3 by Mante & Volger (1967). Their results show dips in thermal conductivity at temperatures corresponding to phase transition points. The results are explained in terms of mode conversion near the transition points. The low lying temperature dependant optical phonon branches can get zero energy at zero wave-vector, which causes permanent polarization of the crystal. Near the transition temperature the optical branches have energies comparable to those of the acoustic branches which usually transport the heat. This influences the number of scattering processes in which optical phonons participate, resulting in a reduction of the conductivity due to acoustic branches. In case transverse optical phonon branch shows enough dispersion and is not scattered too much, one can expect additional conductivity which might compensate for the effect of decreased conduction by the acoustic phonons.
Thermal conductivities and specific heat capacities of a wide spectrum of ferroelectrics, BaTiO3, PbTiO3, KNbO3, KTaO3, NaNbO3 and Pb(Mg1/3Nb2/3)O3 (PMN) single crystals have been measured from 2 to 390 K (Tachibana et al., 2008). Pronounced jumps are found at structural transitions in BaTiO3 and KNbO3. A low-temperature anomaly from soft optical phonons is observed in KTaO3. For PMN and NaNbO3, glass-like behaviour is observed in both thermal conductivity and heat capacity measurements. The glass-like behaviour in NaNbO3 is associated with the phase separation phenomena which have been reported in earlier studies. Thermal analysis techniques such as differential scanning calorimetry (DSC) have been employed by several researchers to probe ferroelectric phase transitions (Setter & Cross, 1980, Podlojenov et al., 2006).
Belov & Jeong (1998) have reported thermal conductivity measurements for two ferroelectric crystals, (NH4)2BeF4 and Rb2ZnCl4, with incommensurate phases. It is found that anomalies exist in the thermal conductivities of these crystals in the I-phases. I-modulation waves cause anomalies in the heat transport processes by scattering of heat carrying phonons rather than by their direct participation as heat carriers. They have employed the steady-state technique for their measurements. Comparatively large samples, of size typically greater than 5 mm3, are needed for these techniques in order to avoid boundary effects. Moreover, comparatively large rises in temperature are often necessary to obtain a reasonably high signal to-noise ratio, which lead to considerable temperature gradients being set up in the sample. These drawbacks make these techniques unsuitable for studying critical thermal conductivity behaviour near phase transitions.
Thermal wave measurements based on a photothermal effect, such as the photothermal deflection technique, photoacoustic method and photopyroelectric measurement do not disturb the thermal equilibrium of the sample during transitions. In these techniques one measures the thermal diffusivity, rather than thermal conductivity. Thermal diffusivity measurements do not suffer from heat losses from the sample during measurements and hence are more accurate than a direct measurement of thermal conductivity by the steady state method. With a proper choice of boundary conditions, photothermal techniques make a simultaneous measurement of thermal diffusivity and thermal effusivity possible, from which the thermal conductivity and specific heat capacity can be extracted. The photopyroelectric technique has been used earlier to measure the variations of thermal conductivity and heat capacity of a few crystalline solids as they undergo phase transitions with temperature (Marinelli et al., 1990; Zammit et al., 1988; Mandelis et al., 1985).
3. The photopyroelectric technique
Complete characterization of the thermal properties of a material requires the determination of the thermal transport properties such as the thermal conductivity as well as the specific heat capacity. Techniques for high resolution measurement of specific heat capacity are well established (Kasting et al., 1980; Thoen et al., 1982). It has been shown that photothermal techniques allow simultaneous measurement of specific heat capacity c
A photothermal technique for the simultaneous determination of the thermal conductivity and specific heat capacity near solid state phase transitions using a pyroelectric detector kept in contact with a thermally thick backing medium has been developed by Menon & Philip (2000). The PPE technique has some distinct advantages, such as its simplicity, good sensitivity and ability to perform nondestructive probing, over other photothermal methods. In this measurement the sample is heated by a modulated light source on one side and the temperature oscillations on the opposite side of the sample are detected with a pyroelectric detector, supported on a thermally thick conductive backing. Since the PPE signal depends on properties of the detector which are also temperature dependent, an accurate temperature calibration of the system must be carried out. The advantage of a thermally thick backing is that there will be sufficient heat exchange between the heated pyroelectric detector and the backing, so that signal fluctuations are reduced to a minimum. This method can, in principle, be adapted to all temperature ranges for all samples and is not limited by the thermal properties of the sample.
The PPE effect is based on the use of a pyroelectric transducer to detect the temperature rise due to periodic heating of a sample by induced light. The temperature variations in the detector give rise to an electrical current, which is proportional to the rate of change of the average heat content, given by (Mandelis & Zver, 1985)
where P is the pyroelectric coefficient of the detector, A is the area of the detector and
is the spatially averaged temperature variation over the thickness of the detector, L
For a thermally thick sample with
where T is the temperature and c
A temperature calibration of the PPE detector is necessary here as all the parameters in equations (Eq. 4.a) and (Eq. 4.b) are temperature dependent. All the thermal parameters can be calculated as functions of the sample temperature, provided that the temperature dependences of the parameters of the pyroelectric detector are known.
4. Experimental methods in PPE measurements
A sample set-up of the type shown in Fig. 1 is generally used for these measurements (Menon & Philip, 2000). A 120 mW He - Cd laser of λ = 442 nm, modulated by a mechanical chopper, has been used as the optical heating source. A 28 μm thick film of PVDF with pyroelectric coefficient P = 0.25 ×10−8 V cm−1 K−1 at room temperature has been used as the pyroelectric detector. The sample is attached to the pyroelectric detector with a thermally very thin layer of a heat sink compound whose contribution to the signal is negligible. The pyroelectric detector attached to the sample is placed on a thermally thick backing medium (copper) which satisfies the boundary condition specified above. The frequency of modulation of the light is kept high enough to ensure that the PVDF film, the sample and the backing medium are all thermally thick. The signal output is measured with a lock-in amplifier. The sample-detector-backing assembly is enclosed in a chamber whose temperature can be varied and controlled as desired. Measurements as a function of temperature have been made at a low heating rate with special care near transition points. A block diagram of the experimental set up is shown in Fig. 2 for illustration.
The experimental set up and procedure should be calibrated and tested to ensure that even minor variations in heat capacity and thermal conductivity do get reflected in the measurements. Practically one measures the PPE amplitude and phase as function of modulation frequency, limiting the frequency to low values so that the sample, detector and backing are all thermally thick. From the amplitude and phase variations one can determine the thermal effusivity and thermal diffusivity following equations (Eq. 4.a) and (Eq. 4.b) respectively. From the values of thermal diffusivity and thermal effusivity, the values of thermal conductivity and specific heat capacity can be determined following equations (Eq. 5.a) and (Eq. 5.b).
Practically one measures the photopyroelectric signal amplitude and phase as function of modulation frequency. One will have inverse frequency dependence for the amplitude and phase beyond the critical frequency when the boundary conditions assumed are satisfied. A fitting of the variations of PPE amplitude and phase with the relations connecting thermal diffusivity and effusivity with phase and amplitude respectively enables one to determine the thermal diffusivity and effusivity. Typical variations of PPE amplitude and phase with modulation frequency obtained during PPE measurements in K2SeO4 are shown in figures 3 a and 3b respectively. The peaks in the curves correspond to characteristic modulation frequency for the sample.
5. Results on specific systems and discussion
The variations in the thermal properties of the ferroelectric crystal Triglycine sulphate (TGS) were reported by Menon & Philip (2000). TGS crystals undergo a para–ferroelectric phase transition at 49.4 °C. This crystal has a monoclinic structure at room temperature. Platelets of the crystal of sub-millimeter thickness were cut with faces normal to a, b and c axes so that the direction of propagation of thermal waves was along one of the axes. A very thin layer of carbon black was coated onto the illuminated surface of the sample to enhance its optical absorption. Measurements were carried out as a function of temperature from room temperature (26 °C) to 55 °C. The thermal thickness of the sample in these experiments was verified by plotting the PPE amplitude and phase against modulation frequency at a number of temperatures between room temperature and 55 °C. The variations of the PPE amplitude and phase as functions of temperature were measured keeping the modulation frequency fixed at 40 Hz. From these, the thermal diffusivity (α
Ferroelectric crystals, which exhibit incommensurate phase transitions include ammonium fluroberrylate (Iizumi & Gesi, 1977), potassium selenate (Iizumi et al., 1977), sodium nitrite (Yamada et al., 1963), thiourea (Goldsmith & White, 1959) etc. Thiourea, with the chemical formula SC (NH2)2, undergoes successive phase transitions at 169 K (T1), 176 K (T2), 180 K (T3) and 202 K (T4). Among the five phases (called I, II, III, IV and V) in the order of increasing temperature, two of them (I and III) are ferroelectric and a superlattice structure appears in the II, III and IV phases (Elcombe & Tayler, 1968). The crystal structure in the room temperature phase V above T4 is orthorhombic and belongs to the space group D162
In the three intermediate phases, II, III and IV between T1 and T4, Shiozaki (1971) analyzed X-ray reflection spectra and concluded that the crystal has an in-commensurate structure. According to his analysis, just above T4 the crystal has a superstructure along the c-axis with a period about eight times as large as that of phase IV. The period of the super structure increases as temperature decreases. So in the vicinity of T1, the period is about ten times as large and at T1 the crystal transforms to the ferroelectric phase I, where the period of the unit cell of the prototype is restored. More elaborate descriptions of the properties of thiourea are available in literature (Wada et al., 1978, Moudden et al., 1978, Mc Kenzie, 1975a, Mc Kenzie, 1975b, Delahaigue et al., 1975, Chapelle & Benoit, 1977).
The thermal properties described above during the incommensurate-commensurate phase transition in thiourea were measured employing PPE technique (Menon & Philip, 2003). Measurements have been done along the three principal directions of thiourea and the observed anisotropy in thermal transport is discussed. The crystals were cut with their faces normal to the [100], [010] and [001] directions of the crystallographic a-, b- and c-axes respectively. Measurements were carried out illuminating the three cut sample faces so that the propagation of the thermal wave is along one of the symmetry directions. The variations of thermal conductivity and heat capacity as functions of temperature across the transition temperatures were measured as outlined above.
It was seen that both PPE amplitude and phase clearly reflect the three successive phase transitions in thiourea. The maximum anomaly was at T1, the temperature at which transition to an in-commensurate phase took place. Anomalies were measured along a, b
and c directions at the same temperatures. The maximum variation was seen along the b-direction, the direction in which the crystal possesses spontaneous polarization in the ferroelectric phase. Fig. 5a shows the variations of thermal diffusivity and thermal effusivity with temperature along the b-axis of thiourea single crystal. As can be seen in this figure, thermal diffusivity shows a decrease with temperature, with distinct minima at the three phase transition points at T1 ≈169 K, T3 ≈176K and T4 ≈ 202 K, in agreement with the already reported values of transition temperatures. Thermal effusivity exhibits an inverse behaviour. It increases with temperature, with sharp peaks occurring at the transition temperatures. Taking into account the various uncertainties of the measurement, the overall uncertainty in the values of α and e are estimated to be less than 5%. Similar anomalies with smaller magnitudes have been obtained for the a- and c-directions as well.
Figure 5b shows the variation of heat capacity of thiourea with temperature. As can be seen in this figure, the three transitions get clearly reflected in the temperature variation of heat capacity as clear anomalies at the transition points. These heat capacity values agree with the values reported by earlier workers (Hellwege & Hellwege, 1969). As can be seen, there is no direction dependence for heat capacity. Figure 5c shows the temperature variation of thermal conductivity along the three symmetry directions (a, b and c) of thiourea. The thermal conductivity exhibits significant anisotropy, as is evident from Fig. 5 c. The three transitions get clearly reflected in the thermal conductivity variations as well. The maximum anomaly at the transition temperatures is seen along the b-axis. The maximum thermal conduction occurs in the direction of predominant covalent bonding, which is along the b-axis in thiourea. This is the direction of spontaneous polarization in this crystal.
Dicalcium Lead Propionate (DLP, with chemical formula Ca2Pb (C2H5COO) 6, belonging to the family of double propionates, is ferroelectric below 333K along the c- axis (Nakamura et al 1965). It undergoes a para to ferro electric phase transition at 333K (Tc1), which is a second
order one. Upon decreasing the temperature further, it undergoes another phase transition at 191K (Tc2), which is first order. The transition at Tc1 is associated with the movement of the ethyl group (C2H5) (Nakamura et al., 1978), but the one at Tc2 is still not understood
well. Even below this transition temperature the material continues to remain ferroelectric. Based on the measurement of the hydrostatic pressure dependence of the crystal structure of DLP above and below the respective phase transitions, Gesi & Ozawa (1975) have proposed that the phases above and below Tc2 are isomorphous to each other. However, on the basis of polarizing microscopic observations and dielectric constant measurements, Gesi (1984) has concluded that the two phases above and below Tc2 are not isostructural.
The crystal structure of DLP is tetragonal at room temperature (Ferroni & Orioli, 1959). The lead atoms are located at 4a positions and calcium atoms at 8b positions. Studies on the pyroelectric properties of DLP associated with its phase transitions have led to the conclusion that DLP crystal between Tc1 and Tc2 is tetragonal and polar, the point group in this phase being C
Even though the specific heat of DLP was reported way back in 1965 (Nakamura et al., 1965), other thermal properties such as thermal conductivity were not. Moreover, systematic thermal analysis following thermogravimetry or scanning calorimetry through Tc1 and Tc2 have not been reported. These measurements in DLP through the transition temperatures have been reported by Manjusha & Philip (2008). These authors have reported thermal transport properties of the sample, thermal diffusivity, effusivity, conductivity and specific heat capacity as a function of temperature following PPE technique. The anisotropy in thermal diffusivity/conductivity along the principal axes as well as their variation through these transition temperatures was measured.
The variations of thermal properties, shown in figures 6 a and 6b, clearly indicate that the thermal properties undergo anomalous variations during phase transitions at 191 K and 333 K. In general, the thermal diffusivity and thermal conductivity show an anomalous decrease during transitions, whereas the heat capacity shows a corresponding anomalous increase. Being an electrical insulator crystal, the major contribution to the heat capacity of DLP is from lattice phonons and the electronic contribution to heat capacity is very small. As the phonon modes undergo variations due to mode instability at the transition points, they absorb excess energy giving rise to enhancement in heat capacity. This is found to get reflected in the DSC curve as well. Again, during the transitions, the phonon mean-free path increases, resulting in a decrease in thermal resistance or a corresponding increase in thermal diffusivity and thermal conductivity. The anisotropy in thermal conductivity is not very high for this crystal. The maximum thermal conduction occurs along the c-axis, which is the direction of spontaneous polarization.
Many experimental and theoretical studies have been carried out by different workers to understand the mechanisms of phase transitions in potassium selenate (K2SeO4) single crystals, ever since the discovery of ferroelectricity and successive phase transitions in this crystal (Aiki et al., 1969). With the occurrence of ferroelectric phase, this material undergoes an incommensurate phase (IC phase) transition. Potassium selenate undergoes three successive phase transitions at temperatures T1 = 745 K, T2 = 129.5 K and T3 = 93 K (Aiki et al 1969). The crystal exhibits hexagonal structure in phase I, with space group D
group D16 2h (Pnam) at T1 (Kalman et al 1970). Then, phase II changes into an incommensurate one (phase III) at T2 (Iizumi et al., 1977); this is a second order phase transition. It undergoes an IC phase transition at T3, below which the crystal is commensurate and ferroelectric with a small spontaneous polarization along the c direction.
Many experimental studies such as dielectric measurements (Aiki et al., 1969, Aiki et al., 1970), X-ray and neutron diffraction (Iizumi et al., 1977; Ohama, 1974; Terauchi et al., 1975), ESR (Aiki, 1970), Raman and Brillouin scattering (Wada et al., 1977a; Wada et al., 1977b; Yagi et al., 1979), ultrasound velocity, attenuation and dispersion studies (Hoshizaki et al., 1980; Shiozaki, 1977) etc have been reported near T2 and T3. The variations in specific heat capacity and thermal expansion of K2SeO4 in the low temperature phase have also been reported before (Aiki et al., 1970; Gupta et al., 1979). Thermal expansion along the c-axis exhibits a discontinuity at the incommensurate to commensurate transition. Specific heat measurements show anomalies at T2 and T3, indicating that the transition at T2 is second order and that the one at T3 is first order (Aiki et al., 1970). In spite of all these measurements reported at temperatures T3 and T2, only very few experimental results have been reported near T1 ( Unruh et al., 1979; Inoue et al., 1979; Cho & Yagi, 1980; Gupta et al., 1979) because of the inherent difficulties involved in carrying out precision experiments at high temperatures. The variation of the specific heat capacity across the structural transition at T1 has not been reported so far for this material. More experimental data are still required for a better understanding of the high temperature phase of this material.
The thermal diffusivity, thermal conductivity and heat capacity of K2SeO4 as it goes through the IC phase between 129.5 and 93 K have been measured by Philip & Manjusha (2009). The anisotropy in thermal conductivity along the three principal directions of this crystal and its variation with temperature are brought out and discussed by these authors. Differential scanning calorimetric (DSC) measurements across the high temperature phases have been carried out to determine anomalies in enthalpy during transition from phase I to phase II, and the calorimetric ratio method adopted to determine the variation of specific heat capacity with temperature across the high temperature transition point T1. The results from PPE and calorimetric measurements have been combined to plot the variation of specific heat with temperature through all the four phases of K2SeO4, and the results discussed below.
PPE measurements were done at temperatures between 85 and 300 K. Thermal diffusivity and effusivity along the c axis, plotted against temperature are shown in Fig. 7 a. From the diffusivity and effusivity values, the values of the thermal conductivity and specific heat capacity have been computed, and these are plotted in Fig 7 b. Since the values of these thermal parameters for a and b axes are not very different from the corresponding values obtained for the c-axis, they are not reproduced. It can be noticed that the thermal conductivity along the c axis, which is the direction of spontaneous polarization for this crystal, is slightly more than that along a- or b-axis at all temperatures. The anisotropy in thermal conductivity is small and decreases as the temperature is lowered. The variations along the c axis clearly indicate that the thermal properties undergo anomalous variation during phase transitions at 93 and 129.5 K. Thermal conductivity and heat capacity exhibit maxima at the phase transition temperatures 93 and 129.5 K. Moreover, there is an overall enhancement in thermal conductivity in the IC phase of K2SeO4 between 93 and 129.5 K. The maxima in thermal conductivity at the phase transition temperatures can be explained in terms of the increase in phonon mean free path or decrease in phonon–phonon and phonon–defect collision rates. Again, the anomalous variation in specific heat capacity is due to softening of phonon modes and the corresponding enhanced contribution of phonon modes to the specific heat capacity.
The IC phase in K2SeO4 has been observed experimentally as satellite peaks in the x-ray and neutron diffraction patterns (Iizumi et al., 1977). In the IC phase of K2SeO4 at temperatures close to T2, the incommensurate modulation wave is pure harmonic. But as the temperature approaches T3, nonlinear phase modes, which are equally spaced commensurate constant phase domains separated by narrow phase varying regions called phase solitons, emerge. The presence of these modulation waves or phase solitons can influence heat conduction in ferroelectric crystals in two different ways, as outlined below.
The phase solitons can affect the mean free path of thermal phonons via scattering and hence can cause anomalous variation of thermal conductivity in the IC phase. Another possibility is that the modulation waves themselves can act as heat carriers, resulting in an enhancement in thermal conductivity. Whether the thermal conductivity increases or decreases during an IC phase transition depends on which factor dominates in the process. One can isolate thermal conductivity enhancement in the IC phase by computing the value of (λ − λbg) where λ is the total thermal conductivity and λbg is the background thermal conductivity in the absence of occurrence of IC modulation. In general, for an insulating crystal, λbg follows an inverse temperature (T) variation.
The theory of heat conduction in a ferroelectric crystal with a two-component order parameter has been developed by Levanyuk and co-workers (Levanyuk et al., 1992). The theory considers heat conduction along the modulation axis of a system that undergoes IC phase transition. According to this, the thermal conductivity due to phase solitons is given by
where c0 and γ are constants and ρ is the magnitude of the order parameter. One can see that the phase solitons enhance the thermal conductivity of K2SeO4 in the IC phase. It has also been shown that the enhancement in thermal conductivity is related to the excess specific heat ce due to order parameter fluctuation as
This explains the enhancement in specific heat in the modulation phase of the crystal. Even without the effects expressed in equations (Eq. 6) and (Eq. 7), the modulation waves can cause anomalies in (λ − λbg) by strongly scattering the heat carrying phonons. In the IC phase between 93 and 129.5 K, one can note that the background thermal conductivity and the specific heat decrease gradually as the temperature increases. This variation of thermal conductivity is normal for a solid, but the variation of the specific heat is just opposite to the normal behaviour for solids. This can be attributed to the increase in the heat capacity of the modulation waves with decrease in temperature. As the system approaches the low temperature commensurate phase, it becomes more and more ordered, resulting in a decrease in entropy or increase in heat capacity. The modulation waves are so strong in the IC phase that the contribution of modulation waves to the overall heat capacity of the system is much more than the contribution of normal phonon modes to heat capacity. This results in an overall increase in heat capacity as the temperature decreases in the IC phase. The DSC curve during the heating cycle shows a clear peak occurring at 745 K, indicating that the phase transition at this temperature is endothermic. The variation of specific heat capacity with temperature up to a temperature well above 745 K has been determined by the DSC ratio method. These results have been combined with the results shown in figure 7b to plot the variation of heat capacity with temperature encompassing all the four phases of K2SeO4. This is shown in Fig. 8. So figure 8 contain the variation of specific heat of K2SeO4 through all the three transition temperatures T1, T2 and T3 (and through all the four phases). The anomalous variation of heat capacity during transitions can be understood as due to softening of the phonon modes and the corresponding enhanced contribution of phonon modes to the specific heat capacity of the system.
In order to estimate the quantity of excess heat capacity due to the structural phase transition at 745 K, the contribution of the normal heat capacity shall be subtracted from the measured molar heat capacity. The background lattice heat capacity was approximated by a third-order polynomial. The excess of the molar heat capacity Δ Cp was plotted against (T − Tc) and it is found to have a shape typical for a continuous phase transition. At T = Tc, Δ Cp is found to be 0.112 ± 0.003 J K−1 mol−1. The specific heat critical exponent α was obtained from the slope of log (Δ Cp) versus log (T − Tc). The value of α is found to be −0.0853 ± 0.0002, which is close to zero. This value for α is typical for a mean field model of a phase transition (Strukov & Levanyuk, 1998). The Landau theory gives a simple relation between the excess entropy and the order parameter P
One can acquire more information about the nature of the phase transition from the excess entropy Δ S. The most direct way to determine Δ S is from a measurement of the excess heat capacity as a function of temperature:
The transition entropy has been calculated from the above equation, and is obtained as Δ S = 0.49 ± 0.03 J K−1 mol−1. This is typical of a structural phase transition. However, this is much smaller than the transition entropy predicted by the order-disorder model in the mean field theory. Other mechanisms such as tunnelling may have to be taken into account to reduce this discrepancy with experiment.
6. Conclusions
The results presented in the above section show that a photothermal technique such as the photopyroelectric technique is a convenient and sensitive one to measure thermal conductivity and specific heat capacity of ferroelectric crystals as they undergo phase transitions. Photothermal techniques do not suffer from the disadvantages of steady state techniques. In a photothermal technique one actually measures the thermal diffusivity which is independent of heat losses from the sample. With a careful control of the sample boundary conditions the PPE technique has proven to be a sensitive and convenient one to measure thermal transport properties of solids that undergo ferroelectric phase transitions.
Even though not much attention has been paid to the measurement of thermal properties for probing phase transitions in solids, it is now more and more obvious that thermal transport measurements yield critical information to throw more light on fine features of ferroelectric transitions, particularly those involving incommensurate modulation of the lattice. Measurement of fine features of the variations of thermal conductivity and specific heat capacity with temperature, without disturbing the system, provides valuable information about the interactions involved in the processes.
Acknowledgments
The author thanks University Grants Commission (New Delhi) and Cochin University of Science and Technology for financial support provided for the publication of this article.
References
- 1.
Aiki H. 1970 ESR Study of γ-Irradiated K2SeO4,29 379 88 - 2.
Aiki K. Hukuda K. Koga H. Kobayashi T. 1970 Dielectric and thermal study of K2SeO4 transitions,28 389 94 - 3.
(1969). Ferroelectricity in K2SeO4, J. Phys. Soc. Japan 26, 1064Aiki K. Hukuda K. Matumura O. - 4.
Ashcroft N. W. Mermin N. D. 1976 (Holt, Rinehart and Winston, New York) Chap. 25 - 5.
Badarinath K. V. S. Radhakrishna S. 1984 Studies on the ferroelectric-paraelectric transition of dicalcium lead propionate ,3 575 577 - 6.
Belov A. Jeong Y. H. 1998 Anomalous heat conduction in ferroelectric crystals with incommensurate phases, J. Korean Phys. Society32 452 455 - 7.
Bhat S. V. Dhar V. Srinivasan R. 1981 ESR studies on phase transitions in double propionates , 39, 1167 - 8.
Blinc R. Levanyuk A. P. 1986 1 & 2, (North-Holland, Amsterdam) - 9.
Chapelle J. P. Benoit J. P. 1977 Raman study of external frequencies of thiourea with temperature ,10 145 51 - 10.
Cho M. Yagi T. 1980 Brillouin scattering study of the Hexagonal-Orthorhombic phase transition in K2SeO4 ,49 429 430 - 11.
Cummins H. Z. 1990 Experimental studies of structurally incommensurate crystal phases 5 & 6, 211 - 12.
Delahaigue A. Khelifa B. Jouve P. 1975 Soft mode in thiourea by Raman measurements ,72 585 89 - 13.
Dettmer E. S. Romenesko B. M. Charles Jr H. K. Carkhuff B. G. Mewll D. J. 1989 Steady-state thermal conductivity measurements of AlN and SiC substrate materials , , Hybrids, and Manufacturing Technology,12 543 548 - 14.
Dorner B. 1981 Investigation of structural phase transformations by inelastic neutron scattering in Structural Phase Transitions I (editors: K A Muller & H. Thomas, in23 Springer-Verlag, Berlin) - 15.
Elcombe M. Tayler J. C. 1968 A neutron diffraction determination of the crystal structures of thiourea and deuterated thiourea above and below the ferroelectric transition ,24 410 20 - 16.
Ferroni E. Orioli P. 1959 Zur kristallstruktur von PbCa2 (CH3CH2COO)6, 111, 362 - 17.
Gaffar M. A. Mebed M. M. El -Fadl A. 1987 Thermal Diffusivity of Pure and Doped TGS Crystals , Phys. Status Solidi a104 879 884 - 18.
Gesi K. 1984 Reinvestigation of pressure-Induced II-III transitions in Ferroelectric Ca2Sr (C2H5COO)6 and Ca2Pb(C2H5COO)6, J. Phys. Soc. Japan53 1602 1605 - 19.
Gesi K. Ozawa K. 1975 Effect of Hydrostatic pressure on the phase transitions in Ferroelectric Ca2Sr (C2H5COO)6 and Ca2Pb(C2H5COO)6,39 1026 1031 - 20.
Goldsmith G. J. White J. G. 1959 Ferroelectric behavior of Thiourea, .31 1175 1187 - 21.
Grigas J. 1996 Microwave dielectric spectroscopy of ferroelectrics and related materials (Gordon and Breach Publishers) - 22.
Gupta S. S. Karan S. Gupta S. P. S. 2000 Growth and defect characterization in single crystals of Ferroelectric Ammonium Sulphate, .39 2736 40 - 23.
Hellwege K. H. Hellwege A. M. (editors-Bornstein Landolt. New Series. 1969 3 ed: (Springer- Verlag, New York)477 - 24.
Hoshizaki H. Sawada A. Ishibashi Y. Matsuda T. Hatta I. 1980 Ultrasonic study of K2SeO4 in the temperature range of the incommensurate phase transition 19, L324 26 - 25.
Inoue K. Suzuki K. Sawada A. Ishibashi Y. Takagi Y. 1979 A test of centrosymmetry of the hexagonal phase in K2SeO4 46 608 10 - 26.
Iizumi M. Axe J. D. Shirane G. Shimaoka K. 1977 Structural phase transformation in K2SeO4, 15, 4392 - 27.
Iizumi M. Gesi K. 1977 Incommensurate pháse in (ND4)2BeF4, Solid State Commun22 37 39 - 28.
John P. K. Miranda L. C. M. Rastogi A. C. 1986 Thermal diffusivity measurement using the photopyroelectric effect ,34 4342 4345 - 29.
K´alm´an A. Stephens J. S. Cruickshank D. W. J. 1970 The crystal structure of K2SeO4, B26 1451 54 - 30.
Kasting G. B. Garland C. W. Lushington K. J. 1980 Critical heat capacity of octylcyanobiphenyl (8CB) near the nematic-smectic A transition 41,879 EOF 884 EOF - 31.
Lebedev N. I. Levanyuk A. P. Minyukov S. A. Vallade M. 1992 Elastic anomalies at structural phase transitions: a consistent perturbation theory. II. Two-component order parameter including the case of incommensurate phase, 2 2293 97 - 32.
Levanyuk A. P. Minyukov S. A. Vallade M. 1992 Elastic anomalies at structural phase transitions: a consistent perturbation theory. I. One component order parameter, 2 1949 63 - 33.
Lines M. E. Glass A. M. 1977 Principles and Applications of Ferroelectrics and related Materials (Clarendon Press, Oxford, 1977) - 34.
Luthi B. Rehwald W. 1981 Ultrasonic studies near structural phase transitions, in (ed: K A Muller & H Thomas, in Topics in Current Physics23 Springer-Verlag, Berlin) - 35.
Mandelis A. Care F. Chan K. K. Miranda L. C. M. 1985 Photopyroelectric detection of phase transitions in solids , 38,117 EOF 122 EOF - 36.
Mandelis A. Zver M. M. 1985 Theory of photopyroelectric spectroscopy of solids,57 4421 4430 - 37.
Manjusha M. V. Philip J. 2008 Thermal properties of Dicalcium Lead Propionate across the prominent transition temperatures , Letters35 107 118 - 38.
Mante A. J. H. Volger J. 1967 The thermal conductivity of BaTiO3 in the neighborhood of its ferroelectric transition temperatures, 24A, 139 - 39.
Marinelli M. . Murtas F. Mecozzi M. G. Zammit U. Pizzoferrato R. Scudieri F. Martellucci S. Marinelli M. 1990 Simultaneous determination of specific heat, thermal conductivity and thermal diffusivity at low temperature via the photopyroelectric technique , A51 387 393 - 40.
Mc Kenzie D. R. 1975a Neutron and Raman study of the lattice dynamics of deuterated thiourea 8, 2003 - 41.
Mc Kenzie D. R. 1975b The antiferroelectric transition in thiourea studied by thermal neutron scattering, 8, 1607 - 42.
Menon C. P. Philip J. 2000 Simultaneous determination of thermal conductivity and heat capacity near solid state phase transitions by a photopyroelectric technique , .11 1744 1749 - 43.
Menon C. P. Philip J. 2003 Thermal properties of Thiourea studied using Photopyroelectric technique ,287 63 70 - 44.
Moudden A. H. . Denoyer F. . Benoit J. P. Fitzgerald W. 1978 Inelastic neutron scattering study of commensurate-incommensurate phase transition in thiourea , 28, 75 - 45.
Nagae Y. . Wada M. . Ishibashi Y. Takagi Y. 1976 Raman Scattering Spectra of Ca2Sr(C2H5CO2)6 and Ca2Pb(C2H5CO2),41 1659 1662 - 46.
Nakamura N. Akamura H. Suga H. Chihara H. Seki S. 1965 Phase transitions in crystalline divalent metal dicalcium propionates I. Calorimetric and dielectric investigations of strontium and lead dicalcium propionates, 8 1779 1787 - 47.
Nakamura N. Suga H. . Chihara H. Seki S. 1978 Phase transitions in crystalline divalent metal dicalcium propionates. II. Proton magnetic resonance investigation ,41 291 296 - 48.
Ohama N. 1974 Superstructure of potassium selenate K2SeO4 ,9 283 88 - 49.
(1975). Pyroelectricity of dicalcium lead propionate associated with its phase transitions, J. Phys. Soc. Jpn. 38, 292Osaka T. Makita Y. Gesi K. - 50.
Philip J. Manjusha M. V. 2009 Thermal transport across incommensurate phases in potassium selenate: Photo-pyroelectric and calorimetric measurements, 21,045901 EOF - 51.
Podlojenov S. Stade J. Burianek M. Mühlberg M. 2006 Study on the ferroelectric phase transition in potassium lithium niobate (KLN) ,41 344 348 - 52.
Setter N. Cross L. E. 1980 The contribution of structural disorder to diffuse phase transitions in ferroelectrics 15 2478 2482 - 53.
Shiozaki Y. 1971 Satellite X-ray scattering and structural modulation of thiourea ,2 245 60 - 54.
Shiozaki S. Sawada A. Ishibashi Y. Takagi Y. 1977 Hexagonal-orthorhombic phase transition and ferroelasticity in K2SO4 and K2SeO4,43 1314 19 - 55.
Standnicka K. Glazer A. M. Bismayer U. 1990 The phase diagram of dicalcium strontium/lead propionate,27 73 80 - 56.
Strukov B. A. Levanyuk A. P. 1998 Ferroelectric Phenomena in Crystals (Springer, Berlin) - 57.
Sunil Misra. K. Jerzak S. 1989 Mn2+ EPR study of phase transitions in dicalcium lead propionate Ca2Pb (C2H5COO)6: Determination of critical exponent below the ferroelectric phase transition and comparison with EPR studies on Ca2Ba(C2H5COO)6 and Ca2Sr(C2H5COO),39 2041 2050 - 58.
Tachibana M. Kolodiazhnyi T. Takayama-Muromachi E. 2008 Thermal conductivity of perovskite ferroelectrics , 93, 092902 - 59.
Takashige M. Hirotsu S. Sawada S. Humano K. 1978 Piezoelectric and elastic properties of Dicalcium lead propionate, J. Phys. Soc . Jpn.45 558 564 - 60.
Terauchi H. Takenaka H. Shimaoka K. 1975 Structural Phase Transition in K2SeO4,39 435 39 - 61.
Thoen T. Marynissen H. Van Dael W. 1982 Temperature dependence of the enthalpy and the heat capacity of the liquid-crystal octylcyanobiphenyl (8CB26 2886 2905 - 62.
Toledano J. Toledano P. 1987 TheLandau theory of phase transitions (World Scienti fic, Singapore), Chapter 5 - 63.
Unruh H. G. Eller W. Kirf G. 1979 Spectroscopic and dielectric investigations of K2SeO4 ,55 173 80 - 64.
Wada M. Sawada A. Ishibashi Y. Takagi Y. 1977 Raman scattering spectra of K2SeO4 ,42 1229 34 - 65.
Wada M. Sawada A. Ishibashi Y. Takagi Y. 1978 Raman scattering spectra of SC (NH2)2,45 1905 10 - 66.
Wada M. Uwe H. Sawada A. Ishibashi Y. Takagi Y. Sakudo T. 1977 The lower frequency soft-mode in the ferroelectric phase of K2SeO4 43,544 EOF 547 EOF - 67.
Yamada Y. Shibuya I. Hoshino S. 1963 Phase transition in NaNO2 ,18 1594 1603 - 68.
Yagi T. Cho M. Hidaka Y. 1979 Brillouin scattering study of the paraelectric-incommensurate phase transition in K2SeO4 ,46 1957 58 - 69.
Zammit U. Marinelli M. Pizzoferrato R. Scudieri F. Martellucci S. 1988 Photoacoustics as a technique for simultaneous measurement of thermal conductivity and heat capacity ,21 935 937